Mauri Pro Sailing

Shopping Cart

Your cart is currently empty.
Boomkicker w/fittings - Sailboats 14 to 16 ft.

Boomkicker w/fittings - Sailboats 14 to 16 ft.

Code: BOOK0312
Price: $79.05


Boomkicker's Boom Track Fittings are an alternative way for attaching the boom to provide extended travel and more adjustment. The new custom extrusions simplifies the design and lowers the price.

Easier setup and adjustment - The new fitting consists of 2 parts, the track and slider attached to the Boomkicker. The track, designed for flat or round bottom booms, uses 3 screws, the same as the standard fitting. The slider is free to move, with the stop set by a clevis pin through the track. 3 positions for the stop are provided. With the added range and adjustment, setting the boom height for installation is less critical. To adjust the height later whether it's for a change in setup, a different mainsail, a bimini, or just to clear heads is done by moving the stop pin. More stop positions can be added if needed. Adjustment does not affect downward travel which is handled by the flexing spring rods.

Lots more upward travel - When straight the Boomkicker is at the top of it's travel. At that point, the boom should be at it's highest operating position. Although the standard boom fitting allows some further upward travel of the boom, with the new fitting, the sky's the limit. This is great for racers during accidental roundups or cruisers who forget to set the vang when sailing downwind in heavy air.
Product No. Use For Boomicker Model Boat Length Std. Track Length
B0790R K0750 25ft 9"/23cm
B1090R K1000 30ft 11"/28cm
B1590R K1500 38ft 12"/30.5

Product Details

Boomkicker K0312: Includes mast fitting with round luff groove slide, Boomkicker with 5/16" diameter spring rods, webbing sling to support the boom, control line from sling to mast and eyestrap with round luff groove slide.

Fits Boats: 14' to 16'.

Imperial Metric
Initial Pin to Pin 30" 76.2 cm
Minimum Pin to Pin 25" 63.5 cm
Maximum Force * 75 lb 34 kg
Maximum Stroke 1 11" 28 cm
Maximum Stroke 2 ** 6" 15.3 cm
* At Maximum Pin to Pin Length.
1 Maximum stroke at initial Pin to Pin.
2 Maximum stroke at min. Pin to Pin.
** Stroke is travel when flexed. 1" of stroke equates to approximately 7" at the aft end of the boom.

The Boomkicker model K0312 works basically the same as the larger models, but instead of attaching directly to the boom, a webbing sling, suspended between the two spring rods, supports the boom.

Designed for smaller daysailers, these Boomkickers are easy to install with no drilling or tapping required. All parts fit in the luff groove of the mast. For trailering, the design makes rigging and de-rigging a snap, simply remove the boom and fold the Boomkicker up against the mast for storage.

The sling, because it does not attach directly to the boom, allows these models to work with the simplest of goosenecks. Even if the boom just slides onto a pin at the gooseneck, or can roll, the Boomkicker can not push the boom back or restrict it from rolling around its central axis to follow the sail.

Note: Uses webbing sling at boom instead of track fitting.

Part Number: K0312

Installation Manual

Recommended Installation Tools:
Phillips Screwdriver, Fine Tooth Hacksaw.

1. General: The Model K0312 Boomkicker is designed for sailboats under 17' (5m) who's boom, with sail, weighs under 16 lbs. (6.8kg). To the right is a sketch of the Model K0312. The Boomkicker comes fully assembled. Two fiberglass rods provide the force to support the boom. The boom sits in the sling between the rods. The sling is held by the line to the gooseneck stop and controls the initial height of the boom. The mast fitting and stop use slides in the luff groove to avoid drilling. As shown, the Boomkicker works by flexing upward and when straight, it is at the top of its travel. The Boomkicker does not restrict the boom from rising higher.

Model 312 Flexed and Straight

2. Installing Mast Bracket and Gooseneck Stop: The Boomkicker works best if the boom/gooseneck is fixed in one spot on the mast. If the boom/gooseneck can slide, then in the normal sailing position with the sail up, place a mark on the mast, indicating the lowest point of the gooseneck inside the luff groove. Then remove. Using the sail opening in the mast, slide the assembled base with bracket and slide to the vang bail, do not tighten. Next slide the top of the gooseneck stop to the mark and tighten. Reposition the boom against the gooseneck stop. If the boom/gooseneck is fixed to the mast, the slides can be detached, slid past the gooseneck and reassembled in position.

3. Final Positioning: Using the main halyard, lift the aft end of the boom 6"- 8" (15cm - 20cm) above horizontal or the normal sailing level. Orient the Boomkicker so the two screw heads on the base are facing downward or aft, and the sling loop for the line is forward. If the Boomkicker fits in the area above the vang, hold the sling around the underside of the boom and adjust the mast fitting location to make an angle between 40° and 45° with the boom. The sling line should be loose and is adjusted later. If the angle is much lower than 40°, then as the spring rods flex, they lose ability to hold the boom. Tighten the bracket in position. If the Boomkicker is too long or the angle too low, it can be cut down. Shorten the bottom of the rods (loosen two small screws in base to pull the rods out) equal lengths of no more than 5" (13cm). A fine tooth hacksaw works best and frayed ends can be avoided by prewrapping a layer of tape around the rod at the cut.

4. Final Adjustments: With the boom/gooseneck held against the stop, adjust the line between the sling and gooseneck stop so the sling supports the boom. Since some initial stretch can be expected under load, slightly overtighten. Disconnect the halyard from the boom and press the boom down to flex the Boomkicker. It should flex freely upward and have enough support for the boom and mainsail without sagging.

WARRANTY: The following is made in lieu of all warranties, expressed or implied. Seller's and manufacturer only obligation shall be to replace or repair such parts of the product proved to be defective for a period of five years. User shall determine the suitability of the product for its intended use and user assumes all risk and liability whatsoever in connection therewith.

For additional information or support, contact Mauri Pro Sailing Technical Team, your Boomkicker specialist.

Compare Chart

Boat LOA
Pin to Pin
Pin to Pin
Initial / Minimum
K0312 14 - 16' 30" 25" 75 lbs. 11" - 6"
K0400 16 - 19' 34" 26" 150 lbs. 11" - 6"
K0500 16 - 20' 36" 26" 150 lbs. 11" - 6"
K0750 20 - 25' 36" 31" 250 lbs. 11" - 6"
K0800 25 - 27' 45" 35" 300 lbs. 15" - 6"
K1000 27 - 30' 45" 41" 400 lbs. 15" - 6"
K1250 30 - 34' 53" 43" 500 lbs. 16" - 9"
K1500 34 - 38' 53" 49" 600 lbs. 16" - 9"
* At Maximum Pin to Pin Length.
1 Maximum stroke at initial Pin to Pin.
2 Maximum stroke at min. Pin to Pin. ** Stroke is travel when flexed.
1" of stroke equates to approximately 7" at the aft end of the boom.

Copyright © 2017 . Mauri Pro Sailing LLC