INSTALLATION MANUAL

System sizing, every car and track part number, track layout, mast mounting, sailmaker's dimensions, reef setup, troubleshooting and replacement parts for the 26 mm and 32 mm Battcar Switch Systems.

DocumentHarken Battcar Switch System 26 mm, 32 mm Installation Manual
FormatPDF · 24 pages · 3.4 MB
LanguageEnglish
Battcar Switch System 26 mm, 32 mm

System Sizing

System Fits boats Cars pass in the switch at
26 mm 50–80 ft (15.2–24 m) 100 mm (3.94") above switch bottom
32 mm 80–130 ft (24–40 m) 163 mm (6.44") above switch bottom

Cars and headboards

Part no. Description System Note
HC9045 Headboard car assembly 26 mm Needs a 3876 or 3877 headboard View part →
HC7493 Intermediate car 26 mm Quantity per sailmaker View part →
HC7324 Batten car, 12 mm threaded stud 26 mm Batten receptacle sold separately View part →
HC7325 Reef car 26 mm Secures the tack when reefing View part →
HC8125 Tack car 26 mm Use with halyard lock to tension luff View part →
C9494 Trysail car 26 mm Use with trysail switch Ask us to source it →
HC9046 Headboard car assembly 32 mm Needs a 3876 or 3877 headboard View part →
HC7322 Intermediate car 32 mm Quantity per sailmaker View part →
HC8098 Batten car, 12 mm threaded stud 32 mm Batten receptacle sold separately View part →
HC7316 Batten car, 14 mm threaded stud 32 mm Batten receptacle sold separately View part →
HC8076 Reef car 32 mm Secures the tack when reefing View part →
HC8099 Tack car 32 mm Use with halyard lock to tension luff View part →
C9342 Trysail car 32 mm Use with trysail switch Ask us to source it →
3876 Standard web-on headboard 26 / 32 mm See sailmaker's instructions View part →
3877 Square-top web-on headboard 26 / 32 mm See sailmaker's instructions View part →

Switch, Storage and Track

Part no. Description System Length Fasteners Hole spacing
HC8220 Switch 26 mm 641 mm (25 1/4") 6 mm (1/4") — View part →
HC8147 Storage track 26 mm 500 mm 6 mm 50 mm View part →
HC8148 Storage track 26 mm 725 mm 6 mm 50 mm View part →
HC10060 Double storage track 26 mm 725 mm 6 mm 50 mm View part →
HC8221 Gate track 26 mm 300 mm 6 mm 75 mm View part →
HC7466 T-track 26 mm 3 m 6 mm 75 mm View part →
HC8879 High-load T-track 26 mm 2 m 6 mm 50 mm View part →
HC8222 Splice link 26 mm — — — View part →
1522A Endstop 26 mm 55 mm — — Ask us to source it →
3884 Track slug-mounting kit, flat mast groove (M6 × 18 mm) 26 mm — Included — View part →
3885 Endstop kit, flat mast groove (M6 × 35 mm) 26 mm — Included — View part →
3886 Gate track mounting kit, flat mast groove (M6 × 18 mm) 26 mm 300 mm Included — View part →
HC7382 Switch 32 mm 724 mm (28 1/2") 8 mm (5/16") — View part →
HC8149 Storage track 32 mm 800 mm 8 mm 50 mm View part →
HC8150 Storage track 32 mm 1025 mm 8 mm 50 mm View part →
3948 Double storage track 32 mm 300 mm 8 mm 50 mm View part →
3949 Double storage track 32 mm 500 mm 8 mm 50 mm View part →
HC8226 Gate track 32 mm 300 mm 8 mm 75 mm View part →
HC7391 T-track 32 mm 3 m 8 mm 75 mm View part →
HC8880 High-load T-track 32 mm 2 m 8 mm 50 mm View part →
HC8227 Splice link 32 mm — — — View part →
548A Endstop 32 mm 72 mm — — Ask us to source it →

26 mm slug-mount tracks (HC7466, HC8879) work with either drill-and-tap or slugs. With HC8879 high-load track, put slugs every 50 mm at the headboard positions for full hoist and reefs; elsewhere every 100 mm to save weight.

Layout

  • Switch height depends on the number of cars and the storage track length.
  • Track must be longer than the luff to allow for stretch, and must not block the halyard exit.
  • A gate track above the switch lets the storage track run down to the gooseneck.
  • High-load track goes at the headboard positions for full hoist and reefs.
  • Storage tracks: endstop holes at the bottom; if shortening, cut from the upper end.

Mounting to the Mast

  • Switch and storage tracks must sit on the same flat surface; build a platform or use wedges on curved masts.
  • Work to a straight reference line. Drill and tap one hole, fit, align, then a second, then the rest.
  • Use blue Loctite instead of oil to lubricate the tap on aluminium masts.
  • Threadlocker on the switch, storage and top track screws; none on the gate track, which comes off to load cars.
  • Carbon spars: consult the mast builder and use reinforcing plates.

Sailmaker's Instructions

Attachment

  • Headboard: 45 mm (1 3/4") webbing; headboard holes take 416 16 mm cheek blocks for the leech line.
  • Maximum distance between attachment points 1.2–1.35 m (4'–4'6").
  • Adding battens can reduce stack height by eliminating luff cars.
  • Load headboard cars with the pegs on the same side: both cars run through the same side of the switch.

Reefing

  • Space reef points halfway between attachment points.
  • Batten fittings and cars cannot take reef outhaul or downhaul loads: take them to a tack fitting.
  • Cars must never be loaded while in the switch.
  • Spray the track slot of the cars with McLube Sailkote before loading, off the boat.
Headboard Description 26 mm A × B 32 mm A × B
3876 Standard web-on headboard 138 × 58 mm 146 × 66 mm View part →
3877 Square-top web-on headboard 146 × 58 mm 154 × 66 mm View part →
416 16 mm cheek block for the leech line — — View part →

Stop hoisting immediately if anything binds at the switch, especially with an electric halyard winch. Forcing it damages the switch fingers and cars.

Troubleshooting

Problem Probable cause Solution
Cars bind Slider damaged or missing Check and replace the slider
Cars bind Dirt in cars Flush with detergent and fresh water, then high-pressure water; clean the track grooves
Cars bind Stud threaded too tightly into the receptacle Back the threaded stud off two turns
Cars stop at the switch Car loaded upside down, pins on the wrong side Remove the car, flip it and reload
Battcar nut not holding Lock nut reused too many times Fit a new 6 mm lock nut
Cars jam when hoisting Headboard or cars catching on lazy jacks Pull the lazy jacks out to the shrouds
Batten receptacle post bending Reef loads going into the receptacle Take reef loads to the mast or gooseneck

Inspect before long passages: loose nuts, cotter pins and track screws, and wear on toggles and batten studs. Flush with fresh water often; no grease unless the instructions call for it.

Parts in this Manual We Carry

Harken part numbers as printed in the installation manual, matched to the genuine parts in our store.

Harken part no. Our part
HC9045 Headboard Cars - Switch - 1 1/32 in (26.0 mm) - Assembly
3876 Batten Car Headboard - Battcar System C Mainsail Sail Plate (Web-On Design) - 14 mm Hole Dia.
3877 Batten Car Headboard - Battcar System C Mainsail Sail Plate (Flat-Top Web-On) - 14 mm Hole Dia.
HC7493 Batten Car System - Intermediate Car - For Battcar Switch System: 26 mm
HC7324 Batten Car Slider w/ Joint - Switch Battcar System - 12mm Stud (75mm Car Length)
HC7325 Batten Reefing Car - For Battcar Switch System - 26mm Track - Boats up to 80 ft - L: 90mm & SWL: 952 kg
HC8125 Batten Car Sliders - Tack w/ Plastic Slides (Low Friction) - For Battcar Switch System: 1.02 in (26 mm)
HC9046 Headboard Cars - Switch - 1 1/4 in (32.0 mm) - Assembly
HC7322 Batten Car System - Intermediate Car - For Battcar Switch System: 32 mm
HC8098 Batten Car Slider w/ Joint - Switch Battcar System - 12mm Stud (90mm Car Length)
HC7316 Batten Car Slider w/ Joint - Switch Battcar System - 14mm Stud (90mm Car Length)
HC8076 Batten Reefing Car - For Battcar Switch System - 32mm Track - Boats up to 140 ft - L: 115mm & SWL: 2722 kg
HC8099 Batten Car Sliders - Tack w/ Plastic Slides (Low Friction) - For Battcar Switch System: 1.26 in (32 mm)
HC8220 Track - T Track w/ Switch (Aluminum) - For Battcar Switch System - W: 1.02 in (26 mm) & L: 2.1 ft (0.64 m)
HC8147 Track - T Track w/ Switch Storage (Aluminum) - For Battcar Switch System - W: 1.02 in (26 mm) & L: 1.6 ft (0.5 m)
HC8148 Track - T Track w/ Switch Storage (Aluminum) - For Battcar Switch System - W: 1.02 in (26 mm) & L: 2.4 ft (0.73 m)
HC10060 Track - T Track w/ Switch Storage (Double) (Aluminum) - For Battcar Switch System - W: 1.02 in (26 mm) & L: 2.4 ft (0.73 m)
HC8221 Track - T Track w/ Switch Gate (Aluminum) - For Battcar Switch System - W: 1.02 in (26 mm) & L: 0.98 ft (0.3 m)
HC7382 Track - Switch (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 2.4 ft (0.73 m)
HC8149 Track - T Track w/ Switch Storage (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 2.6 ft (0.8 m)
HC8150 Track - T Track w/ Switch Storage (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 3.4 ft (1.02 m)
3948 Track - T Track w/ Switch Storage (Double) (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 0.98 ft (0.3 m)
3949 Track - T Track w/ Switch Storage (Double) (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 1.6 ft (0.5 m)
HC8226 Track - T Track w/ Switch Gate (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 0.98 ft (0.3 m)
HC7466 Track - T Track w/ Switch (Aluminum) - For Battcar Switch System - W: 1.02 in (26 mm) & L: 9.8 ft (3 m)
HC8879 Track - T Track w/ Switch (High Load) (Aluminum) - For Battcar Switch System - W: 1.02 in (26 mm) & L: 6.6 ft (2 m)
HC8222 Batten Car Systems - Splice Links - Switch T-Track - For 1.0 in (26.0 mm) Battcar Switch System
HC7391 Track - T Track w/ Switch (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 9.8 ft (3 m)
HC8880 Track - T Track w/ Switch (High Load) (Aluminum) - For Battcar Switch System - W: 1.26 in (32 mm) & L: 6.6 ft (2 m)
HC8227 Batten Car Systems - Splice Links - Switch T-Track - For 1 1/4 in (32.0 mm) Battcar Switch System
3884 Batten Car Systems - Switch Track Mounting Kit - Mast Grooves (Flat) - For Battcar Switch System
3885 Batten Car End Fitting - 26mm Switch System Track End Stop Kit – Flat Mast Groove
3886 Batten Car Systems - Switch System Gate Track Mounting Kit - Mast Grooves (Flat) - For Battcar Switch System
3852 Headboard Cars - CB - Battcar System B - 1 1/16 in (27.0 mm) - Assembly
HFS203 Cotter Pin (5/32" x 1.25") for Unit 2 ESP Furlers
HFS191 Link Plate Flat Washer (3/8") for ESP Unit 1 Furlers
HFS920 Link Plate Lock Nut (7/16") for ESP Unit 1 Furlers
HFS937 Link Plate Lock Nut (M12) for ESP Unit 2 / Unit 3 Furlers

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual