Sizing, parts, 1800 and 2720 track length and installation, car loading, sail attachment, Battslide receptacle assembly, sailmaker's dimensions and troubleshooting for the System A Battcar system in manual 4355.

Sizing and Parts
| System | Max. area, monohull | Multihull | Headboard | Battcars | Luff car |
|---|---|---|---|---|---|
| A low load | 33 m² (350 ft²) | 28 m² (300 ft²) | 1807 | 1901, 1944, 1976, 1977 | 1777 |
| A | 39 m² (425 ft²) | 32 m² (350 ft²) | 1792, 1807 | 1825, 1901, 1944, 1976 | 1894 |
| A hi-load | 51 m² (550 ft²) | 475 ft² | 1792HL | 1825HL, 1901HL, 1944HL, 1976HL, 1977HL | 1894HL |
| Part no. | Description | |
|---|---|---|
| 1800 | Slug-mount track, 2.05 m (6'8 3/4") sections, 22 mm (7/8") wide, 12 mm (1/2") high | Ask us to source it → |
| 2720 | Drill-and-tap track; 10-32 (5 mm) screws not included | Ask us to source it → |
| 2724 | Splice piece, drill-and-tap track | View part → |
| 263 | End stop set, drill-and-tap track | View part → |
| 1792 | Headboard assembly: 2 headboard cars, coupler, 2 headboard plates, four 19 mm rings | Ask us to source it → |
| 1807 | Light-duty headboard coupler car assembly | Ask us to source it → |
| 1777 | Plastic luff slider car | View part → |
| 1894 | Luff car | Ask us to source it → |
| 1825 | Battcar, 10 mm stud | Ask us to source it → |
| 1901 | Battcar with adjustable flat or round Battslide | Ask us to source it → |
| 1944 | Battcar with 40 mm batten receptacle | Ask us to source it → |
| 1976 | Battcar with midi, maxi or fixed round Battslide | Ask us to source it → |
| 1977 | Universal Battcar (receptacle not included) | Ask us to source it → |
Mounting kit, one per track: 15 slugs 19 mm (3/4"), 67 mm (2 5/8") connector slug, blue Loctite, 17 flathead screws 5 × 16 mm. End kit, one per system: two 32 mm (1 1/4") end stops, four 5 × 25 mm screws, two rubber end stops, blue Loctite. Hi-load cars and headboard cars are needed for larger mainsails.
1800 Slug-Mount Track
- Track runs at least 8" above the headboard halyard attachment, clear of the halyard exit, and as close to the gooseneck as possible; allow 1/4" (6 mm) at each end for the end stops. Halyard setback from the aft face of the mast 3 3/4" (96 mm).
- Sections: 5 for 8.763–10.262 m (28'9"–33'8"), 6 to 12.319 m, 7 to 14.376 m, 8 to 16.434 m, 9 to 18.466 m, 10 for 18.491–18.898 m (60'8"–62').
- Cut top and bottom tracks from the charts in the PDF; drill two 5.5 mm (13/64") holes centred 8 mm (5/16") and 27 mm (1 1/16") from the cut end. Bottom track 451, 476 or 502 mm (17 3/4, 18 3/4 or 19 3/4").
- Screws need at least three full turns engaged in the slug. Cars are 57 mm (2 1/4") wide: check they clear any trysail track.
- Run the 67 mm connector slug up the groove first; one drop of blue Loctite per slug hole; 5/8" (16 mm) track screws, 1" (25 mm) end stop screws through the rubber stop.
2720 Drill-and-Tap Track
- Scribe both sides of the old track before removing it; string line for the new one.
- Start at one end and work down; drill square to the mast face without the chuck hitting the track; tap and fit screws with blue Loctite.
- #10 (5 mm) flathead screws, 10 per metre, not included.
- Align joints with 2724 splice pieces and rods or dowels clamped outside the track.
- Bottom track 457–609 mm (18–24") long so cars can be loaded and removed.
Loading Cars and Sail
Loading
- Headboard cars first (1792 has a lug in the centre), then Battcars with the vertical shaft housing at the top. Hold the car loader firmly against the track.
- Fit the bottom track and lower end stop with blue Loctite; end stop screws must pass through the track.
- 1792 coupler: cotter pin end of the clevis pin toward the middle of the coupler. 1807 comes pre-assembled.
- Raise the sail and check it is not too tall.
Battslide Receptacles
- Plastic bushing in each end of the car lug; the shaft goes in threaded end up.
- Always fit a 5/16" (8 mm) washer between the plastic bushing and the nut.
- Tighten the locknut until the shaft starts to bind, then back off 1/8 turn. Too tight, or no washer, damages the plastic liner.
- Replace the 5/16-18 locknut after two uses.
- Lower on a wrap round the winch; on unstayed masts use the vang to stop the head over-rotating.
- Clean at the start of the season or if cars bind; inspect locknuts, bushings and receptacle screws. Shock cord from the spreader tips holds the lazy jacks clear.
Sailmaker's Instructions
| Car | Batten | A | B | C boltrope | D | Fastener |
|---|---|---|---|---|---|---|
| 1777 luff slider | — | 51 mm | 28 mm | — | 19 mm | 5 mm |
| 1792 headboard assembly | — | 200 mm | 41 mm | 71 mm | 197 mm | 9.5 mm |
| 1807 light-duty headboard | — | 200 mm | — | 71 mm | — | 9.5 mm |
| 1825 Battcar, 10 mm stud | Round 17 mm or flat 41 mm | 76 mm | 41 mm | 67 mm | — | 5 mm |
| 1894 luff car | — | 54 mm | 41 mm | — | 19 mm | 5 mm |
| 1901 adjustable Battslide | Round 12 mm; flat 41 × 6 mm | 76 mm | 41 mm | 64 mm | 216 mm | 5/16-18 |
| 1944 40 mm receptacle | Round 16 mm; flat or round | 76 mm | 41 mm | 71 mm | 146 mm | 6 mm |
| 1976 midi / maxi / fixed round | 41 / 51 mm flat; 11 mm round; 12 mm thick | 76 mm | 41 mm | 64 mm | 119 mm | 5/16-18 |
| 1977 universal | — | — | — | — | 20 mm | 6 mm |
- 1792 plates: narrow corner up, 3/16" aluminium semi-tubular rivets in the 15 small holes, 19 mm stainless liners closed so the rings fit the 14 mm (.535") coupler.
- 1807: maximum 40 m² (425 ft²) monohull, 33 m² (350 ft²) multihull; plates 1.5 or 3 mm each, plates plus sail 14 mm (9/16") max. Coupler hole 101 mm (4") from the top, about 38 mm (1 1/2") from the boltrope, liner ID at least 12.7 mm (1/2"); halyard hole about 63.5 mm (2 1/2") aft.
- Luff car setback, luff tape to clevis pin: 1777 44 mm (1944 car) or 35 mm (1901 / 1976); 1894 32 mm or 22 mm.
- Battslide midi takes battens to 41 mm (1 5/8") wide, maxi to 51 mm (2"); 1901 takes flat battens to 41 × 5 mm (filed tabs to 9.5 mm) or 12 mm round.
- Usual attachment spacing 1.2–1.35 m (4'–4'6"); reef points halfway between. Batten fittings cannot take reef outhaul or downhaul loads.
Troubleshooting
| Problem | Probable cause | Solution |
|---|---|---|
| Headboard coupler does not fit | Cars loaded in the wrong order | Remove onto car loaders and reload in order |
| Cars do not fit on track | Track and cars different sizes, or balls missing | Check sizes; reload balls with car loaders |
| Cars bind | Car or receptacle upside down, balls missing or dirt | Refit the right way up; reload balls; flush with detergent then high-pressure water |
| Plastic bushings breaking | Washer not used | Fit the washer under the vertical post nut |
| Batten receptacle does not rotate | Nuts too tight | Loosen slightly |
| Cars jam when hoisting | Catching on lazy jacks | Pull the lazy jacks out to the shrouds |
| Sail will not go fully up | Sail too tall or sheave too far forward | Shorten the sail or move the sheave aft |
| Batten receptacle post bending | Reef loads going into the receptacle | Take reef loads to the mast or gooseneck |
Parts in this Manual We Carry
Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.
| Harken part no. | Our part |
|---|---|
| 1777 | Batten Car System - Intermediate Car (Low Load) - For Battcar System A: 22 mm |
| 2724 | Splice Link - For Tracks: 7/8 in (22.0 mm) |
Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.
Products in this Manual
-

Harken Batten Car System - Intermediate Car (Low Load) - For Battcar System A: 22 mm
HAR1777
$34.95 USDUnit price /Unavailable -
