Sizing, parts and ball chart, track length and cutting, slug-mount and drill-and-tap installation, car loading, sailmaker's dimensions, operation, maintenance and troubleshooting for the Harken Battcar System B.
Download PDF ▾

System Sizing
| System | Max sail area, monohull | Max sail area, multihull | Max boat length | Headboard | Battcars | Luff car |
|---|---|---|---|---|---|---|
| B | 675 ft² (63 m²) | 550 ft² (51 m²) | 58 ft (17.7 m) | 1793 | 1794, 1826, 1902, 1946, 1978, 1979, 1980 | 1895 |
| B High-Load | 800 ft² (74 m²) | 650 ft² (60 m²) | 60 ft (18.3 m) | 1793HL | 1794HL, 1826HL, 1902HL, 1946HL, 1978HL, 1979HL, 1980HL | 1895HL |
System B track is 1 1/16" (27 mm) wide. Cars are 2 3/4" (70 mm) wide: check they clear the trysail track and any other obstruction the full height of the spar.
Track and hardware
| Part no. | Description | |
|---|---|---|
| 1808 | Track, 6' 9 1/8" (2.06 m) lengths, open backed, mounted on slugs in the mast groove | Ask us to source it → |
| 1535 | Track for drilling and tapping | Ask us to source it → |
| 1616 | Track for drilling and tapping | Ask us to source it → |
| 1602 | Track for drilling and tapping | Ask us to source it → |
| 1538 | Splice for 1535 track | Ask us to source it → |
| 1619 | Splice for 1616 / 1602 track | View part → |
| 1522 | End stop set | View part → |
| HFS322 | Flathead screw M5 × .8 × 16 mm (1946 / 1978 receptacle) | Ask us to source it → |
| HFS340 | Nylock nut M5 × .8 (1946 / 1978 receptacle) | Ask us to source it → |
- Headboard assembly: 2 headboard cars, 1 coupler, 2 headboard plates, 4 × 19 mm rings.
- Mounting kit (one per track): 19 mounting slugs 7/8" (22 mm), 1 connector slug 3" (76 mm), 21 flathead screws 6 mm × 20 mm, 2 tubes blue Loctite.
- End kit (one per system): 2 end stops 1 7/16" (36 mm), 4 flat head screws 6 mm × 20 mm, 2 rubber end stops, 1 tube blue Loctite.
- Luff cars are not required if the battens are close enough to support the sail.
Ball Replacement Chart
| Battcar | Car length | Balls per car | Ball part no. | Balls per bag | Ball Ø |
|---|---|---|---|---|---|
| 1793 | 4 3/8" (111 mm) | 48 | 1526** | 25 | 5/16" (8 mm) |
| 1979 | 3 13/16" (97 mm) | 40 | 1583* / 1526** | 25 | 5/16" (8 mm) |
| 1895 | 2 3/4" (70 mm) | 30 | 1583* / 1526** | 25 | 5/16" (8 mm) |
| 1978, 1946, 1980, 1794, 1826, 1902 | 3 13/16" (97 mm) | 40 | 1583* / 1526** | 25 | 5/16" (8 mm) |
* Delrin balls (changed from white to black in 1979). ** Torlon (brown) for high-load aluminium endcaps; "HL" follows the part number.
Track Length
- Track is longer than the sail luff: it must run at least 8" above the halyard attachment on the headboard. Allow for sail stretch.
- The top of the track must not interfere with the halyard exit. Halyard setback from the aft face of the mast is 3 3/4" (96 mm).
- Leave 1/4" (6 mm) beyond each end of the track for the end stops.
- At the bottom, run the track as close to the gooseneck as possible, ideally below the top of the boom.
- Length is set by the number of 2.06 m sections plus cut top and bottom pieces: 7 sections for 42'4"–47'4" (12.903–14.427 m) up to 12 sections for 74'5"–81'. Full top-track cut chart in the PDF (pages 4–5).
- Bottom track: 18 1/8" (460.5 mm), 19 1/8" (486 mm) or 20 1/8" (511 mm) depending on track length (chart on page 8).
- Cut ends: deburr with a file, round the corners that slide on the mast, drill two 17/64" (6.5 mm) holes centred 5/16" (8 mm) and 1 3/16" (30 mm) from the end.
Slug Mounting (1808 Track)
- First check a slug and screw will tighten in your groove and the screw is long enough.
- Check the 3" (76 mm) connector slug fits the feeder opening and runs the full mast on a halyard with a retrieval line.
- Load slugs from the top: 1 7/16" (36 mm) end stop slug, mounting slugs, connector slug at the bottom. Blue Loctite in every connector slug hole.
- Stack tracks one at a time, sliding them up the groove; 3/4" (20 mm) screws loose until all are in place, then tighten from the masthead down.
- Screws must make three full 360° turns after the threads engage in the slug.
- If the mast has prebend you may need to straighten it somewhat (ease the backstay).
Drilling and Tapping (1535 / 1616 / 1602 Track)
- Never drill and tap through 1808 open-backed track: it needs the support of the slugs.
- Use 1/4" (6 mm) flathead screws, not included: 10 fasteners per metre of track.
- Start at one end and work down, drilling, tapping and screwing hole by hole. Do not drill both ends first.
- Drill perpendicular to the mast face; install screws with blue Loctite.
- Align joints with the 1538 / 1619 splice pieces plus round rods or dowels, held with spring or C clamps.
- Before removing old track, scribe a pencil line down both sides as a guide.
- Bottom track 18–24" (457–609 mm) long, so it comes off easily to load cars.
Do not let tracks drop when stacking them up the mast: severe injury can result if the upper tracks fall.
Loading Cars and Sail
- Load the two headboard cars first (1793 headboard cars have the lug in the centre), then the Battcars with the vertical-shaft housing at the top.
- Hold the car loader firmly against the track until the car is fully on.
- Install the bottom track and lower end stop with blue Loctite. End stop screws must pass through the track or the stop does not work.
- 1793: fit the headboard coupler with the cotter-pin end of the clevis pin toward the middle of the coupler.
- Battcars with Battslide receptacles: a 5/16" (8 mm) washer must go between the plastic shaft bushing and the nut. Tighten the locknut until the shaft starts to bind, then back off 1/8 turn.
- Raise the sail and check it is not too tall; have it shortened if needed.
Operation and Maintenance
- Hold the lazy jacks open with shock cord from the lower spreader tips, long enough for the boom to swing fully out.
- Never just let the halyard go: ease the cars down with a wrap on the winch.
- Unstayed masts: use the vang to stop the upper sail over-rotating and damaging batten receptacles.
- Clean cars at the start of the season or if they bind: detergent and water into the balls, move the cars, rinse. No spray lubricants on cars or track.
- Inspect for loosening locknuts and worn plastic bushings. Replace the 5/16"-18 locknut after two uses.
- To remove cars, use a car loader.
Sailmaker's Instructions
| Part no. | Description | Max batten width / Ø | Max batten thickness | Batten shape | Fastener (E) |
|---|---|---|---|---|---|
| 1793 | Headboard car assembly with headboard | — | — | — | 1/2" (12 mm) |
| 1794 | Battcar with adjustable Battslide for round batten | 3/4" (19 mm) | — | Round | 5/16-18** |
| 1826 | Battcar with 10 mm stud for SDA fitting | 13/16" (21 mm) | — | Round | 1/4" (6 mm) |
| 1895 | Luff car | — | — | — | 1/4" (6 mm) |
| 1902 | Battcar with adjustable flat or round Battslide | 1/2" (12 mm) | 3/8" (10 mm) | Flat or round | 5/16-18** |
| 1946 | Battcar with 50 mm batten receptacle | Flat 2" (51 mm) / round 3/4" (19 mm) | 5/16" (8 mm) | Flat or round | 1/4" (6 mm) |
| 1978 | Battcar with 40 mm batten receptacle | Flat 1 5/8" (41 mm) / round 5/8" (16 mm) | 1/4" (6 mm) | Flat or round | 1/4" (6 mm) |
| 1979 | Battcar to accept Battslide with 3/8" stud* | — | — | — | 5/16-18** |
| 1980 | Universal Battcar* | — | — | — | 1/4" (6 mm) |
* Batten receptacle not included. ** Use locknuts. Hi-load Battcars and headboard cars are required for larger mainsails: add "HL" to the part number. Setback dimensions A–D per car are in the drawing on page 13.
Headboard and Luff
- 1792 headboard plates: narrow corner up; 3/16" aluminium semi-tubular rivets in the 15 smaller holes.
- Close the 19 mm stainless liners with a closing tool (Rutgerson 19 mm, or Howe & Bainbridge C423 / C410 for 7/8" rings).
- Inside of the coupler is about 15 mm: make sure the ring fits.
- Usual distance between attachment points 4'–4'6" (1.2–1.35 m); more is possible with a stiffer luff if the boltrope is pretensioned.
- Luff cars: seize the hourglass spacer to the webbing and the webbing to the sail. Setback 1 5/16" (34 mm) or 7/8" (22 mm) depending on car.
Battens and Reefing
- Space reef points halfway between attachment points.
- Batten fittings cannot take reef outhaul or downhaul loads: take them to a tack fitting such as a reefing hook.
- 1979 with Midi (battens up to 1 5/8" / 41 mm) or Maxi (up to 2" / 51 mm) Battslide: 10-24 screws and barrel nuts with blue Loctite.
- 1794: fits round battens up to 3/4" (19 mm); smaller battens take the 3" (76 mm) sleeves. Cut the batten about 1" (25 mm) aft of the mark; tighten the traveller about 1/4" (6 mm) after contact.
- 1902: flat battens up to 1 5/8" (41 mm) wide and 3/16" (5 mm) thick (3/8" / 9.5 mm if the tabs are filed down); round battens 1/2" (12 mm). Six M5 × 16 mm screws with Nylock nuts.
Troubleshooting
| Problem | Probable cause | Solution |
|---|---|---|
| Tracks do not butt up | Cut end of top or bottom track at a joint | Put the anodized end toward the full-length track |
| Tracks do not butt up | Track weight pulling tracks apart | Loosen the bottom screw and push the tracks up the mast |
| Mounting screws will not tighten / slugs do not fit | Wrong slug size | A different slug is required: contact your dealer |
| Track will not slide up mast | Slugs catching on mast splice, track corners catching, too much prebend, clogged groove | Loosen screws slightly, round the corners, ease the backstay, clean the groove |
| Headboard coupler does not fit | Cars loaded in the wrong order | Remove cars onto car loaders and reload in order |
| Cars do not fit on track | Balls missing, or track and cars not the same size | Reload balls; contact your dealer or Harken |
| Cars bind | Dirt in cars, car or receptacle upside down, balls missing | Flush with detergent then high-pressure water; refit the right way up; reload balls |
| Battcar nut not holding | Locknut used too many times | Fit a new locknut |
| Plastic bushings breaking | Washer not used | Fit the washer under the nut on the vertical post |
| Cars jam when raising sail | Headboard or cars catching on lazy jacks | Pull the lazy jacks out to the shrouds with topping lift or rod vang and shock cord |
| Sail will not go all the way up | Sail too tall or sheave too far forward | Have the sail shortened or move the sheave aft |
| Vertical post or pin bending | Reef loads going into the batten receptacle | Transfer reef loads to the mast or boom gooseneck |
Parts in this Manual We Carry
Harken part numbers as printed in the instructions, matched to the genuine parts in our store.
Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.
Products in this Manual
-

Harken Link Plate Flat Washer (3/8") for ESP Unit 1 Furlers
HARHFS191
$0.99 USDUnit price /Unavailable -

Harken End Stop - Low-Beam - For Tracks: 1 1/16 in (27.0 mm) - Set of 2 - w/ 2 Screws
HAR1522
$40.95 USDUnit price /Unavailable -

Harken Torlon Ball Bearings - Dia: 5/16 in (8.0 mm) - Balls: 25
HAR1526
$29.95 USDUnit price /Unavailable -

Harken Delrin Ball Bearings - Dia: 5/16 in (8.0 mm) - Balls: 25
HAR1583
$9.95 USDUnit price /Unavailable -
