INSTALLATION SHEET

Specifications, mounting and control-line setup for the Small Boat CB windward sheeting cars 2744, 2745 and 2746, the 2752 adapter kit, ball replacement and maintenance.

DocumentHarken CB Traveler Cars 4975 Installation Sheet
FormatPDF · 8 pages · 4.1 MB
LanguageEnglish
CB Traveler Cars 4975

Specifications

Car Description Width Length MWL Breaking load
2744 Small Boat CB / low-load 57 mm (2 1/4") 73 mm (2 7/8") 227 kg (500 lb) 1134 kg (2500 lb) Ask us to source it →
2745 Small Boat CB 57 mm (2 1/4") 73 mm (2 7/8") 386 kg (850 lb) 1134 kg (2500 lb) View part →
2746 Small Boat CB / high-load 57 mm (2 1/4") 105 mm (4 1/8") 567 kg (1250 lb) 1134 kg (2500 lb) View part →

Windward sheeting: mainsheet load on the slider opens the leeward cleat, so you can trim the car to windward in one step. Fits Small Boat track 373, 374, 2720, 2721, 2725 and 2751.

CB cars run on CB track (grooved at the waist, supplied since 2002). On older track, CB+ cars can be converted: see the PDF.

Mounting

  • Roll the car onto the track sheave side aft. If it will not roll on easily, check it is CB track.
  • Never remove the ball retaining wires; the car will not roll without them.
  • Do not fit a stand-up spring between the mainsheet block and the car.
  • The 2752 kit converts Small Boat CB cars 2726–2736, 2753 and 2754 to windward sheeting. Use blue Loctite on the screws.

Control Lines

  • 2:1: deadend 6 or 8 mm (1/4 or 5/16") line to a 073 eyestrap at each end of the track.
  • 3:1: a 29 or 40 mm Carbo block or 2740 control at each end; fit the HCP300 becket tube on the car.
  • Always tie stop knots so the car stops before the endstop. The 2746 car jams on endstops without them.
  • Light air and big waves: add Cam-Matic override cleats at the track ends.
  • Tie the car to one side when motoring or moored.

Ball Replacement

Ball set Description For CB cars Balls per car
176 6 mm (1/4") Delrin ball bearings, 21 per set 2726, 2728, 2730 Small Boat 40 View part →
177 6 mm (1/4") Delrin ball bearings, 21 per set 2727, 2729, 2731, 2734 Small Boat high-load 40 View part →
177 6 mm (1/4") ball bearings, 21 per set (the 1250 car takes Torlon balls) 2735, 2736 Small Boat 1250 60 View part →
Part no. Description
2752 Windward sheeting adapter kit for Small Boat CB cars View part →
150KIT 150 Cam-Matic rebuild kit: cam caps and washers, 66 balls, 2 torsion springs View part →

Load and unload balls one at a time through the centre of the retaining clip, car on edge. Do not overfill and do not remove the clip.

Maintenance

  • Flush cars often with fresh water; periodically squirt detergent solution into the centre openings and roll the car back and forth.
  • No spray lubricants: the balls skid instead of rolling. Use 1–2 drops of McLube OneDrop (or light machine oil) on the track ball surfaces.
  • Inspect shackles and control block fittings for fatigue.
  • Every installation needs Harken endstops; rig the controls so the car does not hit them under load.

Parts in this Manual We Carry

Harken part numbers as printed in the installation sheet, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual