INSTRUCTIONS

Specifications, mounting dimensions, bolts and backing plates, installation with sealant washers, inspection and replacement parts for the E2750HB and E3250HB Double-Sheave End Controls.

DocumentHarken Double-Sheave End Controls Instructions
FormatPDF · 2 pages · 0.3 MB
LanguageEnglish
Double-Sheave End Controls

Specifications

Part no. Track Sheave Ø Length Width Max line Height above track MWL Breaking load Purchase
E2750HB 27 mm Midrange 40 mm (1 9/16") 108 mm (4 1/4") 40 mm (1 9/16") 10 mm (3/8") 25 mm (1") 272 kg (600 lb) 544 kg (1200 lb) 3:1 / 4:1 View part →
E3250HB 32 mm Big Boat 57 mm (2 1/4") 155 mm (6 1/8") 57 mm (2 1/4") 10 mm (3/8") 25 mm (1") 318 kg (700 lb) 635 kg (1400 lb) 3:1 / 4:1 View part →

Sold as a pair. For high-beam travelers with the control lines led along the cabintop to cleats or clutches.

Do not use with 1849 track risers or other elevated systems: if the control line angles down too much it rubs on the bottom aluminium plate.

Installation

Part no. High-beam track Mounting bolts (not included) Optional backing plate
E2750HB R27HB, 1618 8 mm A4 (316) or A2 (18-8) H-32316A View part →
E3250HB R32HB, 3156 10 mm A4 (316) or A2 (18-8) H-32557A View part →

US imperial equivalent bolts will not fit.

Dimension (bottom view) E2750HB E3250HB
A 88 mm 133 mm
B 33 mm 57 mm
C 11 mm 17 mm
D 33 mm 47 mm
E 32 mm 46.5 mm
F 22 mm 40 mm

Letters refer to the bottom-view drawing in the PDF.

  • The traveler must sit so there is a flat area at each end for the bolt holes (dimension A).
  • Track ends must be anodized: special-order Harken track cut to length with the end control holes drilled.
  • Follow the R27HB or R32HB track instructions for fastener spacing and spanning, then drill the deck holes for the end controls. Bevel the top of each hole slightly so sealant can mass there.
  • Apply sealant and fit the supplied plastic sealant washer between the deck and the bottom of the track to keep the sealant in the hole.
  • Slip the bolts through the end control, capturing sheaves and spacers, and fit large washers or the backing plate under the nuts below deck.

Maintenance

  • Inspect the track and mounting hardware for loosening, cracks or damage; check the endstops are secure and undamaged.
  • Arrange the control tackle so the car does not hit the endstops under load.
  • Flush cars often with fresh water and periodically with a detergent/water solution; no spray lubricants. A few drops of McLube OneDrop on the track ball surfaces, then wipe off the excess.
  • Clean the track with detergent and water; keep teak cleaners and caustics off.

Failure to inspect tracks and stops can result in the track pulling off the deck suddenly under high load.

Replacement Parts

Part no. Fits Description
H-51790 E2750HB ESP sheave (4) Ask us to source it →
H-38984A E3250HB ESP sheave (4) Ask us to source it →
H-51785 E2750HB Sleeve for sheave (4) Ask us to source it →
H-38985A E3250HB Sleeve for sheave (4) Ask us to source it →
H-32512A E2750HB Sealant washer, CB track (4) Ask us to source it →
H-32569A E3250HB Sealant washer, CB track (4) Ask us to source it →
H-51784 E2750HB Becket rod (2) Ask us to source it →
H-51068 E3250HB Becket rod (2) Ask us to source it →
HFS360 E2750HB End cap screw (2) Ask us to source it →
HFS1221 E3250HB End cap screw (2) Ask us to source it →
H-32316A E2750HB Backing plate (2) Ask us to source it →
H-32557A E3250HB Backing plate (2) Ask us to source it →

Parts in this Manual We Carry

Harken part numbers as printed in the instructions, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual