INSTALLATION SHEET
Track compatibility, hole layout, mounting bolts, installation, replacement parts and car and track care for the 1620 and 6088 ESP Double-Sheave End Controls.
DocumentHarken ESP Double-Sheave End Controls Installation Sheet
FormatPDF · 2 pages · 0.1 MB
LanguageEnglish

Specifications
| Part no. | Size | High-beam track | Mounting bolts (not included) | Optional backing plate | Recommended cars | |
|---|---|---|---|---|---|---|
| 1620 | Midrange | 1618 | 8 mm | H-32316A | 11625 / 1641 | Ask us to source it → |
| 6088 | Big Boat | 3156 | 10 mm | H-32557A | 3165 / 3161 | Ask us to source it → |
Use metric bolts: the US imperial equivalent sizes will not fit.
| End control | A | B | C | D | E | F |
|---|---|---|---|---|---|---|
| 1620 MR | 88 mm | 32.6 mm | 10.6 mm | 33 mm | 22 mm | 32 mm |
| 6088 BB | 133 mm | 56.6 mm | 16.6 mm | 46.5 mm | 40 mm | 46.5 mm |
Hole layout dimensions as lettered on the drawing in the PDF. A is the flat deck area needed at each end of the track for the bolt holes.
Before You Start
- For high-beam traveler installations with control lines led along the cabintop to cleats or clutches.
- Not for use with 1849 track risers or other elevated systems; a control line angled down too far rubs on the bottom aluminium plate.
- Track ends must be anodized: order Harken track cut to length with the end control holes drilled.
- Works best with long cars, where the car control blocks are supported and do not overhang.
Mounting
- Follow the 1618 or 3156 track instructions for fastener spacing and spanning.
- Drill the end control holes and bevel the top so sealant can mass there.
- Apply sealant and fit the supplied plastic sealant washer between deck and track bottom to contain it.
- Slip the bolts through the end control, capturing sheaves and spacers; large washers or a backing plate under the nuts.
Replacement Parts
| Description | Qty/set | Midrange 1620 | Big Boat 6088 |
|---|---|---|---|
| ESP sheave | 4 | H-27352A | H-27353A |
| Sleeve for sheave | 4 | H-31991A | H-32567A |
| Sealant washer, CB track | 4 | H-32512A | H-32569A |
| Sealant washer, 560 track | 4 | — | HCP374 |
| Bumper | 4 | H-35566A | H-37498A |
| Becket spacer | 2 | H-32315A | H-32137A |
| Socket head cap screw | 2 | HFS974 | HFS333 |
| Backing plate (optional) | 2 | H-32316A | H-32557A |
Maintenance
- Cars: flush often with fresh water; periodically squirt detergent solution into the centre openings, roll the car back and forth, then flush.
- No spray lubricants: the balls skid instead of rolling. Use one or two drops of McLube OneDrop (or light machine oil) on the track ball surfaces and wipe off the excess.
- Track: clean with detergent and water.
Parts in this Manual We Carry
Harken part numbers as printed in the installation sheet, matched to the genuine parts in our store.
| Harken part no. | Our part |
|---|---|
| 1849 | CB Track - Riser Set - For Tracks: 1 1/16 in (27.0 mm) |
Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.
Products in this Manual
-

Harken CB Track - Riser Set - For Tracks: 1 1/16 in (27.0 mm)
HAR1849
$1,147.95 USDList Price: $1,304.00 USDUnit price /Unavailable
