INSTRUCTIONS

Specifications, track compatibility, mounting, 3:1 and 4:1 reeving, how to use windward sheeting, override cleating, the 1637 adapter kit, ball replacement and replacement parts for the Midrange Windward Sheeting Cars.

DocumentHarken Midrange Windward Sheeting Cars Instructions
FormatPDF · 5 pages · 0.8 MB
LanguageEnglish
Midrange Windward Sheeting Cars

Specifications

Car Description Width Length MWL Breaking load
1635 Midrange CB 105 mm (4 1/8") 108 mm (4 1/4") 816 kg (1800 lb) 2268 kg (5000 lb) View part →
1636 Midrange CB / high-load 105 mm (4 1/8") 132 mm (5 3/16") 1043 kg (2300 lb) 2268 kg (5000 lb) View part →

Windward sheeting: mainsheet load on the slider assembly opens the leeward cleat, so the car trims to windward in one step. The 1637 kit fits 1624 / 1625 cars only (not T27 cars), plus old-style endcap cars 1508 and 1509.

Track Width (A) Height (B) Base (C)
1602, R27 27 mm (1 1/16") 14 mm (9/16") 25 mm (1")
R27HB 27 mm (1 1/16") 42 mm (1 5/8") 31 mm (1 7/32")

CB cars ship for CB track, grooved at the waist for the retaining clips, first supplied by Harken in 2003. On older track only CB+ cars can be converted: see the PDF.

Mounting and Reeving

  • Butt the car against the track with the angled sheaves facing forward, toward the bow, and slide it on. Do not remove the ball retaining wires.
  • End controls: a Midrange E2730 or 1631 single-sheave end control at each end of the track, for 3:1 or 4:1.
  • 3:1: 8 mm (5/16") or 10 mm (3/8") line. Deadend to the angled sheaves by reeving downward with a stop knot, then around the end control sheave, around the top sheave on the windward mechanism and out through the cleat.
  • 4:1: same line. Splice or cow-hitch the eye to the deadend eyestrap on the E2730 or the bail on the 1631, reeve down through the angled sheave, around the end sheave, around the top sheave and out through the cleat.
  • Tie stop knots in the line ends so the car is not damaged in an uncontrolled gybe.
  • Splice: loosen one screw, remove the other, rotate the bail to capture the loop; refit with blue Loctite.

Using It

  • Pull the windward control line to position the car; no need to release the leeward cleat.
  • On a tack the car stays put until you pull it to windward.
  • If the car is pulled to windward and dropped back to the centreline before a tack, the leeward line will be slack and the car will drop below the centreline after the tack.
  • If the car releases in slatting conditions (big waves, little wind), mount a Harken 150 cam cleat near each end of the traveler to override the mechanism.
  • Tie the car to one side when motoring or moored, or cleat the lines in the override cleats.

1637 Adapter Kit and Replacement Parts

  1. Remove the screws holding the swivel ears or control blocks on top of the car; keep them.
  2. Position the windward adapter kit with the angled sheaves facing forward.
  3. Refit the screws with a few drops of blue Loctite and tighten firmly.
Part no. Pos. Description
HFS107 1 Trusshead screws 10-32X1.5" (4) Ask us to source it →
201 2 Eyestraps (2) Ask us to source it →
150SP 3 Cam cleats, special (2) View part →
HFS118 4 Cotter pin Ask us to source it →
HCP507 5 Clevis pin Ask us to source it →
HCP218 6 Plastic slide set Ask us to source it →
150BALLS — Cam cleat ball replacement kit View part →
150KIT — Cam rebuild kit (parts and balls) View part →

Ball Replacement

Ball set Car Car length Balls per car Balls per set Ball Ø
1526 1635 Midrange CB 108 mm (4 1/4") 48 Torlon 25 8 mm (5/16") View part →
1526 1636 Midrange CB / high-load 132 mm (5 3/16") 60 Torlon 25 8 mm (5/16") View part →

Car on edge with the retaining clip in place: push one ball at a time in (or out) through the centre of the clip. Do not overfill and never remove the clip. CB+ conversion for track built before 2003 follows the same clip, corner keeper and car loader sequence as the other CB+ cars: see the PDF.

Maintenance

  • Flush cars often with fresh water; periodically squirt a detergent/water solution into the centre openings, roll the car back and forth, then flush the bearings.
  • No spray lubricants: the balls skid instead of rolling. Use 1–2 drops of McLube OneDrop (or light machine oil) on the track ball surfaces, roll the car through it and wipe off the excess. Too much oil attracts dirt.
  • Clean the track with detergent and fresh water.
  • Keep teak cleaners and caustic solutions off: discoloration is not covered by the Harken warranty.

Inspect shackles and control block fittings often for fatigue. Every installation needs Harken track endstops; arrange the control tackle so the car does not hit them under load.

Parts in this Manual We Carry

Harken part numbers as printed in the instructions, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual