INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, dimensions, both deck-mounting procedures, strip-down, torques and the parts list for the Performa 20.2 PT plain-top winch.

DocumentHarken Performa 20.2 PT Plain-Top Winch Installation & Maintenance Manual
FormatPDF · 16 pages · 2.1 MB
LanguageEnglish
Performa 20.2 PT Plain-Top Winch

Specifications

Power ratio Gear ratio
1st speed 6.95 : 1 1 : 1
2nd speed 19.20 : 1 2.76 : 1

The theoretical power ratio does not take friction into account.

Version Weight
PT 2.0 kg
Dimension mm
Base Ø 137
Top Ø 73.5
Height 128
Line entry height 61

Maximum working load (MWL): 550 kg (1213 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Mount on a flat area of deck, reinforced if needed to take at least twice the MWL. Bolts are not supplied.
  • Five M6 bolts through Ø6.2 mm holes on a Ø110 mm bolt circle.
  • A4 stainless bolts only (DIN 267 part 11). No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Fill the holes with marine sealant and clear excess from the base drain channels.
  • The drive gear position is marked by an icon on the skirt. A drilling template is on harken.com.

Two Ways In

  • Procedure 1: unscrew the central screw and lift off the drum (13) with the socket (17) and washer (20); mind the pawls (4) inside the plain top. Use socket-head bolts.
  • Procedure 2: unclip the skirt (2) with a flat screwdriver, fit five M6 hex-head bolts, then press the skirt back until it clips onto the base.

Maintenance

Strip-down after Procedure 1: unscrew the three screws (16), remove the socket support (12), slide out the central shaft (7) and the housing bushing, remove the pin (6), then gears (3) and (11).

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off the winch, especially anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos and stickers.
  • Keep the holes and drain channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season; full overhaul, clean and lubricate at least every 12 months.
  • Replace worn or damaged parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water; dry with cloths that leave no residue.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Brush Harken grease lightly on gears, gear pins, teeth and moving parts. Excess grease reaching the pawls can compromise safety.
  • Oil the pawls and springs lightly. Never grease the pawls.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Screw (10) with washer (9) 4 Nm (35 in-lb)

To fit a pawl, seat the spring in its housing, hold it closed and slide the pawl in. Check each pawl opens and closes easily with a finger.

Spare Parts

From the Performa 20.2 PTP parts list. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A94136900 1 Assy housing Winch 20 View part →
A94138600 2 Assy skirt Winch 20 View part →
A94136700 3 Assy gear Z18 View part →
S000080003 4 Pawl Ø8 * View part →
S000380001 5 Pawl spring Ø8 * View part →
S413700004 6 Pin View part →
S415660002 7 Central shaft W20 PT Ask us to source it →
S268890080 9 Washer View part →
M0604003 10 Screw M6 × 12 UNI 5933 View part →
S413620041 11 Gear Z21 View part →
S4151400A0 12 Socket support PT View part →
S663740053 13 Performa drum W20 View part →
S663730153 14 Performa plain top W20 Ask us to source it →
M0638803 15 Screw M5 × 14 UNI 5931 Ask us to source it →
M0601903 16 Screw M6 × 16 UNI 1207 View part →
S418930152 17 Socket PT A Ask us to source it →
S415130085 18 Washer Ø7.7 × Ø25 × 5.8 View part →
M0614303 19 Screw M8 × 20 UNI 6109 View part →
S678720082 20 Washer Ø56.5 × Ø75 × 1.5 View part →
S678290080 21 W20 drum upper bushing Ask us to source it →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual