INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, dimensions, deck mounting, strip-down, torques and the parts list for the Performa 40.2 PT plain-top winch.

DocumentHarken Performa 40.2 PT Plain-Top Winch Installation & Maintenance Manual
FormatPDF · 16 pages · 2.2 MB
LanguageEnglish
Performa 40.2 PT Plain-Top Winch

Specifications

Power ratio Gear ratio
1st speed 13.50 : 1 2.13 : 1
2nd speed 39.90 : 1 6.28 : 1

The theoretical power ratio does not take friction into account.

Version Weight
PT 3.5 kg
Dimension mm
Base Ø 156
Top Ø 80.5
Height 152
Line entry height 82

Maximum working load (MWL): 850 kg (1874 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Mount on a flat area of deck, reinforced if needed to take at least twice the MWL. Bolts are not supplied.
  • Five M6 bolts through Ø6.2 mm holes on a Ø123 mm bolt circle.
  • A4 stainless bolts only (DIN 267 part 11). No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Fill the holes with marine sealant and clear excess from the base drain channels.
  • A drilling template is on harken.com.

Getting the Drum Off

  • Unscrew the central screw.
  • Slide off the hub (27), the cover (25) and the washer (29).
  • Lift off the drum (21), then bolt the base down with socket-head bolts.

Maintenance

Strip-down after the drum is off: unscrew the three screws (24), remove the socket support (20), slide out the central shaft (18), unscrew the six hex screws (15) and remove the drum support (14). Washer (11) may stay inside the drum support. Then the gearing (6) and its pawls (4), gears (2), (13) and (9), and shaft (7). Check the balls in the drum race and push any loose ones back in.

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off the winch, especially anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos and stickers.
  • Keep the holes and drain channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season; full overhaul, clean and lubricate at least every 12 months.
  • Replace worn or damaged parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water; dry with cloths that leave no residue.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Brush Harken grease lightly on gears, gear pins, teeth and moving parts. Excess grease reaching the pawls can compromise safety.
  • Oil the pawls and springs lightly. Never grease the pawls.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Drum support hex screws (15, six) 8 Nm (71 in-lb)

To fit a pawl, seat the spring in its housing, hold it closed and slide the pawl in. Check each pawl opens and closes easily with a finger.

Spare Parts

From the Performa 40.2 PTP parts list. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A96633200 1 Performa Winch 40 base assy View part →
S413020004 2 Gear Z12 View part →
S413030004 3 Pawls carrier Ø8xN2 View part →
S000090004 4 Racing pawl Ø8 * View part →
S000380001 5 Pawl spring Ø8 * View part →
S412830041 6 Gear Z23 View part →
S657380004 7 Performa pin Ø9 × 10 W40 Ask us to source it →
S279090002 8 Washer Ø36 × Ø9.5 × 1 View part →
S412970004 9 Gear Z20 View part →
S657370041 10 Performa pinion Z13 W40 Ask us to source it →
S413120002 11 Washer Ø22.5 × Ø45 × 1 View part →
S413070004 12 Pin Ø9 × Ø12 × 32.5 View part →
A94130500 13 Assy gear Z20 View part →
A94141500 14 Assy housing Winch 40 View part →
M0635103 15 Socket head screw M6 × 16 UNI 5931 (6) View part →
S657280052 16 Performa shim W40 Ask us to source it →
A74136000 17 Bearing Ø56 × Ø68 × 24 (2) View part →
A94151900 18 Assy central shaft W35 Ask us to source it →
S4151400A0 20 Socket support PT View part →
A96572600 21 Performa drum W40 (with bearing ring and 49 balls 3/16") View part →
S657330153 22 Performa plain top W35/40 Ask us to source it →
M0603703 23 Screw M6 × 12 UNI 5931 (4) Ask us to source it →
M0600903 24 Screw M6 × 20 UNI 5931 (3) Ask us to source it →
S415540153 25 Cover W40 PT Ask us to source it →
S415220080 26 PT spacer View part →
A94136400 27 Assembly socket W20-80 View part →
M6033794 28 Bushing XSM-1012-20 Ask us to source it →
S678720082 29 Washer Ø56.5 × Ø75 × 1.5 View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A96633200 Winch Spare for Performa Size 40 - Base Assembly
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S413960085 Winch Spare for Radial Size 35 to 40 - Bushing (9 x 11 x 12)
S413330085 Winch Spare for Radial Size 46 - Bushing (12 x 14 x 11)
S413020004 Winch Spare for Radial Size 35 to 50 - Gear Z12
S413030004 Winch Spare for Radial Size 35 to 70 - Pawls Carrier (8xn2)
S000090004 Winch Spare for Performa Size 35 to 70 - Pawl 8 Dia. 17-4PH (B009)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S412830041 Winch Spare for Radial Size 35 to 46 - Gear Radial Z23
S279090002 Winch Spare for Radial Size 35 to 40 - Washer (36x9
S412970004 Winch Spare for Radial Size 40 - Gear Z20
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S413070004 Winch Spare for Radial Size 35 to 50 - Pin
A94130500 Winch Spare for Radial Size 35 to 40 - Gear Assembly Z20
A94141500 Winch Spare for Radial & Performa Size 40 - Housing Assembly
S414890080 Winch Spare for Radial Size 35 to 40 - Bushing Housing (9 x 11 x 7)
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
M0635103 Winch Spare for Radial Size 35 to 40 - Socket Head Screw M6x16 Uni 5931
A74136000 Winch Spare for Radial & Performa Size 60 to 70 - Needle Roller Bearing (56 x 68 x 24)
S413880002 Winch Spare for Radial Size 35 to 50 - Center Shaft Washer
S4151400A0 Winch Spare for Radial Size 20 to 46 - Socket Support
A96572600 Winch Spare for Performa Size 40 - Drum
S415220080 Winch Spare for Radial Size 46 - Socket Washer/Spacer
A94136400 Winch Spare for Radial Size 15 to 80 - Assembly Socket
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
S678720082 Winch Spare for Radial Size 20 to 40 - Washer
— Plain Top Winch Performa Size 40 - Aluminum Black / Two Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual