INSTALLATION & MAINTENANCE MANUAL

Three-speed ratios, working load, dimensions, deck mounting, the strip-down procedure, torques and the full parts list for the Performa 50.3 ST winch, with notes on the 55.3 ST.

DocumentHarken Performa 50.3 ST Winch Installation & Maintenance Manual
FormatPDF · 23 pages · 2.2 MB
LanguageEnglish
Performa 50.3 ST Winch

Specifications

50.3 power ratio 50.3 gear ratio 55.3 power ratio 55.3 gear ratio
1st speed 4.3 : 1 1 : 1 4.3 : 1 1 : 1
2nd speed 11.2 : 1 2.4 : 1 11.2 : 1 2.4 : 1
3rd speed 50.8 : 1 10.9 : 1 55.2 : 1 11.8 : 1

The theoretical power ratio does not take friction into account.

Version Weight
50.3 STP 6.9 kg
55.3 STP 6.9 kg
Dimension mm
Base Ø 195
Top Ø 111
Height 220.5
Line entry height 96.3

Maximum working load (MWL) of the 50.3 ST and 55.3 ST: 1450 kg (3197 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Mount on a flat area of deck, reinforced if needed to take at least twice the MWL. Bolts are not supplied.
  • Five M8 socket-head bolts through Ø8.2 mm holes.
  • A4 stainless bolts only (DIN 267 part 11). No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Fill the holes with marine sealant and clear excess from the base drain channels.
  • Place the final pinion so the line with the highest load comes to the winch within the 30° area shown in the PDF drawing.

Getting the Drum Off

  • Unscrew the M8 central screw.
  • Slide off the socket and the covers.
  • Unscrew the three M6 screws and remove the stripper arm.
  • Lift off the drum, then bolt the base down.
  • Position the self-tailing arm so the tail leads into the cockpit.

Maintenance

Strip-down after the drum is off: unscrew the three M6 screws and remove the stripper arm support; unscrew the four M4 screws and remove the flange and central disconnection button; unscrew the two M4 screws and the four M6 screws; slide off the gear with its two pawls and springs, then the supports and the three satellite gears (lever the elastic ring off with a flat screwdriver or punch); gears and pins in sequence, the central shaft, the five M8 screws and the housing; then the central and idler axle gears, the final axle gears and the four pawls. Products: anti-seize, medium threadlocker, Harken grease, Harken pawl oil, Vaseline oil.

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off the winch, especially anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos and stickers.
  • Keep the holes and drain channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season; full overhaul, clean and lubricate at least every 12 months.
  • Replace worn or damaged parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, brush, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water; dry with cloths that leave no residue.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Brush Harken grease lightly on gears, gear pins, teeth and moving parts. Excess grease reaching the pawls can compromise safety.
  • Oil the pawls and springs lightly. Never grease the pawls.
Fastener Torque
M8 central screw 40 Nm
Three M6 screws (installation step 3) 16 Nm
Three M6 screws (disassembly step 1) 4 Nm
Four M6 screws (disassembly step 6) 16 Nm
Five M8 housing screws 20 Nm

When refitting the jaws, the peeler goes between them with the letters TOP facing up, and the stripper arm lines up with the peeler. Check each pawl opens and closes easily with a finger.

Spare Parts

From the Performa 50.3 STP parts list. The 55.3 STP adds A96807500 (Performa drum W50.3), S743640004 (gear Z14), S743650041 (gear Z38) and S743660080 (cover 55.3), with renumbered positions: see the PDF. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A96633400 1 Performa assembly base Winch 50 View part →
S413020004 2 Gear Z12 View part →
S416050004 3 Pin View part →
S278170002 4 Washer Ø12.5 × Ø48 × 1.5 View part →
S412800041 5 Gear Z30 View part →
S414260004 6 Pawls carrier Ø8xN2 View part →
S000090004 7 Pawl Ø8 (6) View part →
S000380001 8 Pawl spring Ø8 (8) View part →
S415590041 9 Gear Z20 View part →
S415610004 10 Pinion Z11 View part →
A72821800 11 Roller bearing Ø14 × Ø20 × 18 (2) View part →
S281340080 12 Spacer roller bearings (2) View part →
S413120002 13 Washer Ø22.5 × Ø45 × 1 View part →
S413070004 14 Pin Ø9 × Ø12 × 32.5 View part →
A94156000 15 Assembly gear Z11 View part →
A96807100 16 Assembly housing Winch 50.3 Ask us to source it →
M0606303 17 Screw M8 × 25 UNI 5931 (5) View part →
A74135100 18 Bearing Ø85 × Ø97 × 26 (2) View part →
A96572400 20 Performa W50 drum View part →
M0619580 20 Ball 3/16" (68) Ask us to source it →
S6573100A3 20 Performa bearing ring W50 Ask us to source it →
A96807900 21 Performa assembly jaws W50.3 Ask us to source it →
S414280080 21 Peeler W46 - 50 View part →
S385970001 21 Spring (4) Ask us to source it →
M0601803 22 Screw UNI EN ISO 1207:1996 M6 × 35 A4 (4) View part →
S680820019 23 Performa black stripper arm W50.3 Ask us to source it →
S6808400A5 24 Cover 50.3 Ask us to source it →
S657320052 25 Performa shim W50 Ask us to source it →
S680750004 26 Ring gear Z=90 Ask us to source it →
S680730052 27 Stripper arm support 50.3 Ask us to source it →
S680760002 28 Pin Ø8 (3) Ask us to source it →
S680740004 29 Gear Z=30 Z=15 (3) Ask us to source it →
M6049294 30 Bushing Ø8 × Ø10 × 12-04 (6) Ask us to source it →
M0635103 31 Socket head screw M6 × 16 UNI 5931 (3) View part →
M0604194 32 Bushing Ø20 × Ø23 × 11 Ask us to source it →
M0624103 33 Screw M4 × 16 UNI 5931 (14) View part →
M0630701 34 Elastic retaining ring shaft Ø50 × 1.57 Ask us to source it →
A73746200 35 Bearing Ø70 × Ø82 × 30 Ask us to source it →
S680870052 36 Flange Ask us to source it →
S4155700A0 37 Stripper arm support Ask us to source it →
M0601903 38 Screw M6 × 16 UNI 1207 (3) View part →
S680830080 39 Cover 50.3 Ask us to source it →
S416520019 40 Socket handle Ask us to source it →
S680720004 41 Central shaft 50.3 Ask us to source it →
S415130085 42 Washer Ø7.7 × Ø25 × 5.8 View part →
M0614303 43 Screw M8 × 20 UNI 6109 View part →
A76808000 44 Assembly clutch 1st direct Winch 50.3 Ask us to source it →
S680810080 45 Button 3 speed Ask us to source it →
S680770004 46 Gear Z=45 Ask us to source it →
M0637394 47 Bushing Ø16 × Ø18 × 17 Ask us to source it →
S680780004 48 Clutch 1st direct W50.3 Ask us to source it →
S377510001 49 Clutch spring Ask us to source it →
S396950004 50 Special pawl Ø8 (2) Ask us to source it →
S680880041 51 Insert (2) Ask us to source it →
M6020494 52 Bushing Ø8 × Ø10 × 12 (3) Ask us to source it →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A96633400 Winch Spare for Performa Size 50 - Base Assembly
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S414890080 Winch Spare for Radial Size 35 to 40 - Bushing Housing (9 x 11 x 7)
S413330085 Winch Spare for Radial Size 46 - Bushing (12 x 14 x 11)
S413020004 Winch Spare for Radial Size 35 to 50 - Gear Z12
S416050004 Winch Spare for Radial Size 50 - Pin
S278170002 Winch Spare for Radial Size 46 to 70 - Washer (12.5 x 48 x 1.5)
S412800041 Winch Spare for Radial Size 50 - Gear Z30
S414260004 Winch Spare for Radial Size 46 to 50 - Pawls Carrier (8 x N2)
S000090004 Winch Spare for Performa Size 35 to 70 - Pawl 8 Dia. 17-4PH (B009)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S415590041 Winch Spare for Radial Size 50 - Gear Z20
S415610004 Winch Spare for Radial Size 50 - Pinion Z11
A72821800 Winch Spare for Radial Size 60 to 80 - Roller Bearing (14x20x18)
S281340080 Winch Spare for Radial Size 50 - Spacer roller bearings
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S413070004 Winch Spare for Radial Size 35 to 50 - Pin
A94156000 Winch Spare for Radial Size 50 - Assy Gear Z11
M0606303 Winch Spare for Radial Size 46 to 70 - Screw (M8x25 UNI 5931)
A74135100 Winch Spare for Radial & Performa Size 50 to 90 - Needle Roller Bearing (85 x 97 x 26)
A96572400 Winch Spare for Performa Size 50 - Drum Assembly
S414280080 Winch Spare for Radial Size 46 to 50 - Peeler
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
M0635103 Winch Spare for Radial Size 35 to 40 - Socket Head Screw M6x16 Uni 5931
M0624103 Winch Spare for Electric Size 46 to 60 - Screw M4 x 16
M0601903 Winch Spare for Radial & Performa Size 60 to 70 - Screw M6x16 UNI1207
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
— Self Tailing Winch Performa Size 50 - Aluminum Black / Three Speed
— Self Tailing Winch Performa Size 50 - Aluminum Black / Two Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual