INSTALLATION & MAINTENANCE MANUAL

Three-speed ratios, working load, deck mounting, the strip-down and lubrication procedure, torques and the full parts list for the Performa 60.3 ST winch.

DocumentHarken Performa 60.3 ST Winch Installation & Maintenance Manual
FormatPDF · 17 pages · 3.9 MB
LanguageEnglish
Performa 60.3 ST Winch

Specifications

Speed Power ratio Gear ratio
1st speed 9.20 : 1 2.20 : 1
2nd speed 20.20 : 1 4.80 : 1
3rd speed 60.70 : 1 14.40 : 1

The theoretical power ratio does not take friction into account.

Version Weight
ST 12.8 kg
Dimension mm
Base Ø 236
Drum Ø 121
Height 253
Line entry height 116

Maximum working load (MWL): 1800 kg (3968 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Six M8 bolts through Ø9 mm holes on a Ø204 mm bolt circle (winch outside Ø236 mm). A drilling template is on harken.com.
  • Bolts are not supplied: use A4 stainless (DIN 267 part 11), sized for your deck. No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Bed the holes in marine sealant, clean off the excess and keep the base drainage channels clear.
  • Position the self-tailing arm so the tail leads into the cockpit.

Getting to the Base

  • Remove the drum and use socket-head (SH) bolts, or strip further and use hex-head (HH) bolts.
  • SH route: central screw, socket and cover, three stripper-arm screws, stripper arm (rotate and lift), drum.
  • HH route: also remove the stripper arm housing, the clutch assembly, the central shaft and the six housing hex screws, then the drum housing.
  • The 3rd-speed gear assembly stays inside the drum housing.
  • Tools: medium flat screwdriver.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Keep the holes and drainage channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months. Replace worn parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 6 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs lightly. Never grease the pawls: excess grease near the pawls compromises safety.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Stripper arm screws (3) 4 Nm (35 in-lb)
Housing hex screws (6) 20 Nm (177 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)

If the jaws come apart, refit the peeler between them with the letters TOP facing up, and align the peeler with the stripper arm.

Performa 60.3 ST Spare Parts

From the Performa 60.3 STP parts list in the manual. Parts marked * come in the Harken service kit. Clutch pin spring: fit it with the pin pointing up, wound anticlockwise from the pin.

Harken code Pos. Description
A96556000 1 Performa assy base W60 Ask us to source it →
S476030004 1 Centering bushing Ø12 Ask us to source it →
S4152300A7 1 Bushing Ø22ר25×9.5 View part →
S415580085 1 Bushing Ø12ר35×9 View part →
S414400004 2 Gear Z14 W60 Ask us to source it →
S413030004 3 Pawls carrier Ø8×N2 View part →
S000090004 4 Racing pawl Ø8 * View part →
S000380001 5 Pawl spring Ø8 * View part →
S414390041 6 Ratchet gear Z21×N2 View part →
S413120002 7 Washer Ø22.5ר45×1 View part →
S278170002 8 Washer Ø12.5ר48×1.5 View part →
S281010004 9 Pin for gear View part →
S414420041 10 Ratchet gear Z26×N4 View part →
S414410004 11 Pawls carrier gear Z13 N4 View part →
A72821800 12 Roller bearing Ø14ר20×18 View part →
S416030004 13 Gear pin Ø12ר18×52.5 View part →
S414480004 14 Idler and pinion Z23/Z13 W60 Ask us to source it →
A74162300 15 Roller bearing Ø24ר18×18 View part →
A94190800 16 Assy housing winch 60.3 Ask us to source it →
S415810081 16 Bushing Ask us to source it →
M0606303 17 Screw M8×25 UNI 5931 View part →
A74145000 18 Roller bearing Ø95ר107×26 View part →
A94143800 19 Assy shaft winch 60 View part →
S413880002 19 Washer Ø17.2ר32×1.5 View part →
S4155700A0 21 Stripper arm housing Ask us to source it →
A96555900 22 Performa assy jaws W60 View part →
S414850080 22 Peeler W60–70 View part →
S683520001 22 Ø7-Ø1-L30 mm spring Ask us to source it →
A96537500 23 Spare kit drum winch 60 ST Performa View part →
M0610280 23 Ball 5/16" Ask us to source it →
M0601803 24 Screw UNI EN ISO 1207 M6×35 A4 View part →
S657410019 25 Performa black stripper arm W60 View part →
M0601903 26 Screw M6×16 UNI 1207 View part →
S4167500B1 27 Cover 3 speed W60 Ask us to source it →
A94154700 28 Assy socket 3 speed Ask us to source it →
S415130085 28 Washer Ø7.7ר25×5.8 View part →
M0614303 28 Screw M8×20 UNI 6109 View part →
S280870041 29 Gear IV Ask us to source it →
S414580081 30 Shim bushing 3 speed Ask us to source it →
S415400004 31 Pawls carrier 3 speed Ask us to source it →
A73129200 32 Roller bearing Ø50ר62×20 Ask us to source it →
S377510001 33 Clutch spring Ask us to source it →
A73422600 34 Bearing Ø45ר55×12 Ask us to source it →
A94158000 35 Assy clutch 3rd speed W60 Ask us to source it →
S415420004 35 Dog clutch 3 speed Ask us to source it →
M6009463 35 Spring loaded ball plunger Ø6 Ask us to source it →
A94145300 36 Assy gear 3rd speed Ask us to source it →
S414530004 36 Idler gear 3 speed Ask us to source it →
S414550081 36 Bushing Ø22ר25×15.5 Ask us to source it →
S414540080 36 Washer 3 speed Ask us to source it →
M0604003 36 Screw M6×12 UNI 5933 View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF come in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S415580085 Winch Spare for Radial Size 60 - Bushing (12 x 35 x 9)
S413030004 Winch Spare for Radial Size 35 to 70 - Pawls Carrier (8xn2)
S000090004 Winch Spare for Performa Size 35 to 70 - Pawl 8 Dia. 17-4PH (B009)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S414390041 Winch Spare for Radial Size 60 to 70 - Ratchet Gear Z21xN2
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S278170002 Winch Spare for Radial Size 46 to 70 - Washer (12.5 x 48 x 1.5)
S281010004 Winch Spare for Radial Size 70 - Pin
S414420041 Winch Spare for Radial Size 60 to 70 - Ratchet Gear Z26xN4
S414410004 Winch Spare for Radial Size 60 to 70 - Pawls Carrier Gear Z13xN4
A72821800 Winch Spare for Radial Size 60 to 80 - Roller Bearing (14x20x18)
S416030004 Winch Spare for Radial Size 70 - Gear Pin (12x18x52.5)
A74162300 Winch Spare for Radial Size 50 to 70 - Roller Bearing 24x18x8
M0606303 Winch Spare for Radial Size 46 to 70 - Screw (M8x25 UNI 5931)
A74145000 Winch Spare for Radial & Performa Size 60 - Needle Roller Bearing (95 x 107 x 26)
A94143800 Winch Spare for Radial & Performa Size 60 - Shaft Assembly
S413880002 Winch Spare for Radial Size 35 to 50 - Center Shaft Washer
A96555900 Winch Spare for Performa Size 60 - Jaw Assembly
S414850080 Winch Spare for Radial Size 60 to 70 - Peeler
A96537500 Winch Spare for Performa Size 60 - Drum
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
S657410019 Winch Spare for Performa Size 60 - Black Stripper Arm
M0601903 Winch Spare for Radial & Performa Size 60 to 70 - Screw M6x16 UNI1207
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
M0604003 Winch Spare for Radial Size 20 - Screw (M6x12 UNI 5933)
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
A96753600 Winch Spare for Electric Size 60 - Shaft Assembly (17-4 PH)
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
M6015697 Winch Spare for Radial Size 60 to 70 - O Ring (5 x 5 x 1 Orm 0055)
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
— Self Tailing Winch Performa Size 60 - Aluminum Black / Two Speed
— Self Tailing Winch Performa Size 60 - Aluminum Black / Three Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual