Mechanical advantage, loads and dimensions, gear ratio changes, line sizes and lengths, mounting, loading the control lines, use, maintenance, troubleshooting and the drawing parts lists for the Harken Pro-Trim Traveler Control.
Download PDF ▾

Specifications
Pro-Trim is a line-driven power system: a drive sheave turns, via a shaft and gear set, a pair of take-up spools. The drive sheave box gives 2.7:1 from the sheave-to-axle diameter; three gear ratios in the dual spool assembly give an overall 9.7:1 to 17.4:1. Systems are custom designed for each application.
| Part no. | Description | Overall advantage | Sheave / spool Ø | L × W × H | MWL | Breaking load | |
|---|---|---|---|---|---|---|---|
| C12329 | Drive sheave, 1260 g (44 oz) | — | 150 mm (5.91") | 114 x 218 x 217 mm (4.48 x 8.59 x 8.56") | 227 kg (500 lb) | 680 kg (1500 lb) | Ask us to source it → |
| C13519 | Dual spool assembly | 9.7:1 | 48 mm (1.88") | 301 x 140 x 129 mm (11.83 x 5.5 x 5.06") | 680 kg (1500 lb) | 1361 kg (3000 lb) | Ask us to source it → |
| C13525 | Dual spool assembly | 14.1:1 | 48 mm (1.88") | 301 x 140 x 129 mm (11.83 x 5.5 x 5.06") | 680 kg (1500 lb) | 1361 kg (3000 lb) | Ask us to source it → |
| C12328 | Dual spool assembly (C12328.SP1 includes the idler gear to convert to 14.1:1) | 17.4:1 | 48 mm (1.88") | 301 x 140 x 129 mm (11.83 x 5.5 x 5.06") | 680 kg (1500 lb) | 1361 kg (3000 lb) | Ask us to source it → |
| H-50575 | Coupler shaft | — | — | 114 x 17 mm (4.5 x .625") | — | — | Ask us to source it → |
| H-44836 | Universal coupler kit | — | — | — | — | — | Ask us to source it → |
Suggested hardware: high-load thru-deck sheaves at the traveler ends, low-load thru-deck sheaves for the drive sheave, Carbo T2 blocks as fairleads with the shock cord tension system, 57 mm Carbo blocks to turn the drive line on deck each side, 150 Cam-Matic cleats for the drive line, and a coupler drive shaft with universal if the drive sheave and spool assembly are apart.
Changing the Gear Ratio
- Remove the gear box cover (five screws).
- Remove the idler gear and shaft.
- Choose the idler gear for the ratio you want.
- Fit the gear and shaft in the matching hole so the gears mesh.
- Refit the cover with blue Loctite 242.
| Part no. | Ratio / unit | Gear outer Ø | Bushings | |
|---|---|---|---|---|
| H-50348 | 17:1, C12328 | 47.6 mm (1.87") | Two H-43838 | Ask us to source it → |
| H-50350 | 9.67:1, C13519 | 58 mm (2.28") | Two H-43838 | Ask us to source it → |
| H-50349 | 14:1, C13525 | 36 mm (1.42") | Two H-43838 | Ask us to source it → |
As printed on page 3. The drawings at the back of the PDF list H-50348 (9.83 idler gear) in the 9.67:1 unit and H-50350 (17.66 idler gear) in the 17:1 unit: confirm the code with Harken before ordering.
Lines and Fasteners
- Drive sheave: four 6 mm (1/4") round or truss head machine screws, nuts and washers. Dual spool: eight of the same.
- Drive line: 10 mm (3/8") softer line with a core, spliced into a loop after loading it on the sheave and through the deck blocks. The splice must be perfect, smooth and constant diameter: have an experienced rigger do it.
- Drive line length: just enough for the trimmer to hike out and still work it, with enough slack that easing the traveler fully keeps the line inside the boat.
- Spool lines: two lengths of 3/16" or 1/4" (5 mm or 6 mm) high-strength Spectra / Dyneema. Allow 2 to 3 wraps on the spool plus the run through guide blocks and thru-deck sheaves to the car.
- A shock cord tension system is required so line runs off the spool when the traveler is eased.
Mounting
- Direct coupling: join drive sheave and spool assembly with the coupler shaft and the M6x1x55 SHCS (HFS1058). If apart, use a shaft with universal joints to take up misalignment.
- Use the installation plate to align the spool brackets and as a drilling template, then remove it.
- Leads must be direct: the drive loop in line with the thru-deck sheaves; the spool lines perpendicular to the spool axle and leaving from the top of the spool.
- First lead block 3' (1 m) or more from the dual spool assembly.
- Mount the 57 mm Carbo blocks higher than the cleats so pulling from the other side uncleats the line; the 2151 57mm T2 loop block can be lashed to footrests.
Loading the Lines
Spool Lines
- Do not cut the line yet. Run it from one track end along the track, into the thru-deck sheave, through the lead and tensioning blocks, to one side of the take-up spool.
- The spools turn in the same direction as the connecting shaft: wind so the car moves the right way when you pull the drive loop.
- Deadend to the centre plate with 2 to 3 wraps, so the knot never takes shock load when the car hits the track end.
- Car at the opposite end: cut and temporarily knot to the car. Keep tension, turn the spool until the car reaches the other end.
- Lead the second side the same way, wrapped the opposite direction, deadended with 2 or 3 wraps. Check one side winds on as the other pays out.
- Do not splice to the car: eye splice about 6" (152 mm) short and lash it, so it can be adjusted. Tension with the car at one end, centre it and take up the slack with the shock cord below deck.
Drive Line
- Release the pusher sheave bungee by compressing the cord locks in the supports.
- Run the 10 mm (3/8") line between the stripper and guide sheave and around the drive sheave, then out through the deck block and all turning blocks.
- Have a rigger make the end-for-end splice with some slack in the loop.
- Retension the pusher sheave bungee so the splice can pass but the drive sheave does not free-wheel.
Use and Maintenance
- Cleat the car at centre for prestarts and downwind, and cleat the lines when moored or docked, so the car cannot crash side to side.
- In a tack hold the control line: once it unloads you already have the new side in hand. Easing, always keep load on the line so the drive does not free-wheel.
- Maintenance: decouple the drive shaft, remove the gear cover, clean and regrease. Replace worn or damaged line and shock cord.
| Problem | Solution |
|---|---|
| Cannot pull the traveler up, or too much force | Centre the line on the dual spools, at right angles to the spool |
| Line piles up on the leeward side of the spool assembly | Use the shock cord tensioning system |
| Drive sheave free-wheels | Tighten the pusher sheave bungee adjuster |
Parts from the Drawings
Drive sheave unit C12329 (drawing H-68634, 1.26 kg):
| Part no. | Pos. | Description | |
|---|---|---|---|
| H-68879 | 1 | Pin (2) | Ask us to source it → |
| H-68883 | 2 | M5X0.8X30 hex SHCS, titanium (2) | Ask us to source it → |
| MP-3021 | 3 | Fastener isolator (4) | Ask us to source it → |
| H-46372 | 4 | Stripper | Ask us to source it → |
| 265 | 5 | Assembly (2) | View part → |
| H-68636 | 6 | Frame cover | Ask us to source it → |
| HFS1358 | 7 | M5X0.8X16 hex SHCS, titanium (2) | Ask us to source it → |
| H-68640 | 8 | Delrin washer 0.438 X 0.177 X 0.031 (4) | Ask us to source it → |
| HFS1360 | 9 | M4X0.7X6 hex BH, titanium (4) | Ask us to source it → |
| H-68663 | 10 | 5/16 flanged Igus bearing (8) | Ask us to source it → |
| H-68638 | 11 | Aluminium sheave (2) | Ask us to source it → |
| H-68637 | 12 | Carbon arm (4) | Ask us to source it → |
| HFS1359 | 13 | M4X.7X10 hex BH, titanium (4) | Ask us to source it → |
| H-68878 | 14 | 60x radially drilled drive sheave | Ask us to source it → |
| H-68635 | 15 | Primary frame | Ask us to source it → |
| A73165300 | 16 | Plastic cage 480 bearing (2) | Ask us to source it → |
| H-40544A | 17 | Drive shaft washer (2) | Ask us to source it → |
| H-40551A | 18 | Smalley ring DNH-32-S02 (2) | Ask us to source it → |
| HCP2009 | 19 | Smalley WST-87-SO2 retaining ring | Ask us to source it → |
| H-68882 | 20 | 1/4" barrel lock (2) | Ask us to source it → |
| H-68881 | 21 | Drive unit shaft | Ask us to source it → |
| MP-119 | 22 | Ball 0.1563 (60) | Ask us to source it → |
| CV740 | 23 | 1/4" shock cord | Ask us to source it → |
| HCP237 | 24 | Hog ring 1/4IN, stainless (2) | Ask us to source it → |
| HCP443 | 25 | Shrink tubing 1/2IN adhesive (2) | Ask us to source it → |
| H-69446 | 26 | Compression spring (2) | Ask us to source it → |
Dual spool unit C13519, 9.67:1 (drawing H-75538, max line load 680 kg, 1.87 kg). C12328 (17:1) uses the same parts except the idler gear (H-50350) and five H-43838 bushings:
| Part no. | Pos. | Description | |
|---|---|---|---|
| H-50345 | 1 | Bearing race | Ask us to source it → |
| MP-121 | 2 | Ball 0.1875 (62) | Ask us to source it → |
| HBB85ASSY | 3 | Roller assembly (2) | Ask us to source it → |
| HFS1058 | 4 | M6x1x55 SHCS, A4 | View part → |
| H-43838 | 5 | Igus bearing GFI 0607-06 (3) | Ask us to source it → |
| H-50343 | 6 | Base box | Ask us to source it → |
| A73165300 | 7 | Plastic cage 480 bearing | Ask us to source it → |
| HFS1213 | 8 | M6 X 1.0 X 10 SHCS (6) | Ask us to source it → |
| H-68911 | 9 | Secondary bracket | Ask us to source it → |
| H-68909 | 10 | Dual line spool | Ask us to source it → |
| H-68910 | 11 | Primary bracket | Ask us to source it → |
| H-68912 | 12 | Installation plate | Ask us to source it → |
| H-38349A | 13 | Torlon machined roller 0.1875 x 0.365 (4) | Ask us to source it → |
| H-50344 | 14 | Gear box cover | Ask us to source it → |
| HFS747 | 15 | M6 x 1.0 x 16mm SHCS (3) | View part → |
| H-50346 | 16 | Input gear shaft | Ask us to source it → |
| H-40544A | 17 | Drive shaft washer | Ask us to source it → |
| H-40551A | 18 | Smalley ring DNH-32-S02 | Ask us to source it → |
| H-50355 | 19 | Output shaft key (2) | Ask us to source it → |
| HCP1927 | 20 | Smalley ring WS-109-SO2 | Ask us to source it → |
| HFS1215 | 21 | M6x1.0 X 35MM SHCS (2) | Ask us to source it → |
| H-50352 | 22 | Idler shaft | Ask us to source it → |
| H-50348 | 23 | 9.83 idler gear | Ask us to source it → |
| H-50347 | 24 | Output gear | Ask us to source it → |
Spool mounting dimensions are in the drawings (pages 14–15 of the PDF).
Parts in this Manual We Carry
Harken part numbers as printed in the installation manual, matched to the genuine parts in our store.
| Harken part no. | Our part |
|---|---|
| HFS1058 | Link Plate Leg Collar Screw for ESP Unit 0 Furlers |
| 2151 | Block - Carbo T2 Loop 57mm Single |
| HFS747 | Drum Torque Tube Screws for MKIV Unit 2 Furlers |
Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.
Products in this Manual
-
-
-

Harken Link Plate Leg Collar Screw for ESP Unit 0 Furlers
HARHFS1058
$2.88 USDUnit price /Unavailable
