INSTALLATION & MAINTENANCE MANUAL

Ratio, working load, deck mounting, the strip-down and lubrication procedure, torques and the full parts list for the single-speed Radial 15 ST winch.

DocumentHarken Radial 15 ST Winch Installation & Maintenance Manual
FormatPDF · 15 pages · 2.0 MB
LanguageEnglish
Radial 15 ST Winch

Specifications

Speed Power ratio Gear ratio
1st speed 16.90 : 1 2.43 : 1

The theoretical power ratio does not take friction into account.

Version Drum Weight
ST A Anodized aluminium 2.1 kg
Dimension mm
Base Ø 120
Top Ø 73.5
Height 138
Line entry height 58

Maximum working load (MWL): 450 kg (992 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five M6 bolts, socket-head (SH) or hex-head (HH), through Ø6.5 mm holes on a Ø100 mm bolt circle (winch outside Ø120 mm).
  • Bolts are not supplied: use A4 stainless (DIN 267 part 11), sized for your deck. No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Bed the holes in marine sealant, clean off the excess and keep the base drainage channels clear.
  • Position the self-tailing arm so the tail leads into the cockpit.

Getting to the Base

  • Remove the drum: central screw, socket and cover, three screws, self-tailing arm (rotate and lift), drum.
  • Tools: medium flat screwdriver.
  • A drilling template is available from Harken.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Keep the holes and drainage channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months. Replace worn parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs lightly. Never grease the pawls: excess grease near the pawls compromises safety.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Jaw screws (3) 4 Nm (35 in-lb)
Shaft screw and washer (pawl access) 4 Nm (35 in-lb)

If the jaws come apart, refit the peeler between them with the letters TOP facing up, and align the peeler with the stripper arm.

Radial 15 ST Spare Parts

From the Radial 15 STA parts list in the manual. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A96781600 1 Assy housing winch 15 View part →
S413740085 1 Bushing Ø9ר11×9 Ask us to source it →
S413960085 1 Bushing Ø9ר11×12 View part →
S413720080 1 Bushing Ø55ר62×34 Ask us to source it →
S4137300B2 1 Washer Ø33.5ר58×5.5 View part →
S4137100A7 1 Bushing Ø28ר33×25 View part →
S4129400A0 2 Stripper arm support View part →
S000380001 3 Pawl spring Ø8 * View part →
S000080003 4 Pawl Ø8 * View part →
S678200004 5 Winch 15 pin Ask us to source it →
A96781900 6 Assy gear Z14 Ask us to source it →
S418730080 6 Bushing Ø9ר11×7 Ask us to source it →
S678170053 7 Winch 15 drum Ask us to source it →
S281670097 8 Red line View part →
A96620900 11 Performa W20 jaws assembly View part →
S663760080 11 Performa peeler W20 Ask us to source it →
S385970001 11 Spring Ask us to source it →
S268890080 12 Washer View part →
M0604003 13 Screw M6×12 UNI 5933 View part →
S678180002 14 Winch 15 shaft Ask us to source it →
A94136400 15 Assy socket W20–80 View part →
S415130085 15 Washer Ø7.7ר25×5.8 View part →
M0614303 15 Screw M8×20 UNI 6109 View part →
S413620041 16 Gear Z21 View part →
M6009103 17 Screw M5×35 UNI EN ISO 1207 A4 View part →
S413570019 18 Stripper arm W20 View part →
M6007103 19 Screw M6×50 UNI 6107 View part →
S6782300A5 20 Cover 1 speed winch 15 Ask us to source it →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF come in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual