INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, deck mounting, the strip-down and lubrication procedure, torques and the BBB and CCC parts lists for the Radial 20.2 PT plain-top winch.

DocumentHarken Radial 20.2 PT Plain-Top Winch Installation & Maintenance Manual
FormatPDF · 16 pages · 1.8 MB
LanguageEnglish
Radial 20.2 PT Plain-Top Winch

Specifications

Speed Power ratio Gear ratio
1st speed 6.95 : 1 1 : 1
2nd speed 19.20 : 1 2.76 : 1

The theoretical power ratio does not take friction into account.

Version Finish Weight
PT BBB / CCC All bronze / all-chrome bronze 3.60 kg
Dimension mm
Base Ø 137
Top Ø 73.5
Height 128
Line entry height 61

Maximum working load (MWL): 550 kg (1213 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five M6 bolts through Ø6.2 mm holes on a Ø110 mm bolt circle (winch outside Ø137 mm).
  • Bolts are not supplied: use A4 stainless (DIN 267 part 11), sized for your deck. No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Bed the holes in marine sealant, clean off the excess and keep the base drainage channels clear.
  • Position the self-tailing arm so the tail leads into the cockpit.

Getting to the Base

  • Unscrew the central screw and lift off the drum with the socket.
  • Bolt down with socket-head (SH) or hex-head (HH) bolts.
  • Tools: medium flat screwdriver.
  • A drilling template is on harken.com.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Keep the holes and drainage channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months. Replace worn parts with original Harken parts only.

Strip-down

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • After the drum: three screws and socket support, central shaft, pin, then the two gears.
  • Shaft screw and washer give access to the pawls.
  • Clean, inspect, grease gears and oil pawls as for all Harken winches; never grease the pawls.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Shaft screw and washer 4 Nm (35 in-lb)

Check each pawl opens and closes easily with a finger before refitting the drum.

Radial 20.2 PT Spare Parts

From the BBB (all bronze) and CCC (all-chrome bronze) parts lists in the manual; drum, plain top and socket differ by finish. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A96874100 1 Assy housing winch 20 Ask us to source it →
S413740085 1 Bushing Ø9ר11×9 Ask us to source it →
S413960085 1 Bushing Ø9ר11×12 View part →
S413720080 1 Bushing Ø55ר62×34 Ask us to source it →
S4137300B2 1 Washer Ø33.5ר58×5.5 View part →
S4137100A7 1 Bushing Ø28ר33×25 View part →
A94136700 2 Assy gear Z18 View part →
S418730080 2 Bushing Ø9ר11×7 Ask us to source it →
S000080003 3 Pawl Ø8 * View part →
S000380001 4 Pawl spring Ø8 * View part →
S413700004 5 Pin View part →
S415660002 6 Central shaft W20 PT Ask us to source it →
S268890080 8 Washer View part →
M0604003 9 Screw M6×12 UNI 5933 View part →
S413620041 10 Gear Z21 View part →
S7027000A0 11 Socket support winch 20 PT Ask us to source it →
S416650043 12 Drum 20 BBB Ask us to source it →
S416690043 12 Drum C W20 (CCC) Ask us to source it →
S281670097 13 Red line View part →
S416670043 14 Plain top W20 BBB Ask us to source it →
S416710043 14 Plain top W20 C (CCC) Ask us to source it →
S678720082 15 Washer Ø56.5ר75×1.5 View part →
M0638803 16 Screw M5×14 UNI 5931 Ask us to source it →
M0601903 17 Screw M6×16 UNI 1207 View part →
S416640046 18 Socket PT BBB Ask us to source it →
S416680046 18 Socket PT C (CCC) Ask us to source it →
S415130085 19 Washer Ø7.7ר25×5.8 View part →
M0614303 20 Screw M8×20 UNI 6109 View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF come in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual