INSTALLATION & MAINTENANCE MANUAL

Ratio, working load, both deck-mounting routes, the strip-down and lubrication procedure, torques and the parts lists for every Radial 20 ST version (STA, STC, STCW, STBBB, STCCC).

DocumentHarken Radial 20 ST Winch Installation & Maintenance Manual
FormatPDF · 23 pages · 3.0 MB
LanguageEnglish
Radial 20 ST Winch

Specifications

Speed Power ratio Gear ratio
1st speed 19.20 : 1 2.76 : 1

The theoretical power ratio does not take friction into account.

Version Drum Weight
STA Anodized aluminium 2.4 kg
STC / STCW Chrome bronze / chrome-white 3.4 kg
STBBB / STCCC All bronze / all-chrome bronze 3.9 kg
Dimension mm
Base Ø 137
Top Ø 73.5
Height 148
Line entry height 61

Maximum working load (MWL): 550 kg (1213 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five M6 bolts through Ø6.2 mm holes on a Ø110 mm bolt circle (winch outside Ø137 mm).
  • Bolts are not supplied: use A4 stainless (DIN 267 part 11), sized for your deck. No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • STA, STC and STCW: an icon on the skirt marks the drive gear position.
  • Bed the holes in marine sealant, clean off the excess and keep the base drainage channels clear.
  • Position the self-tailing arm so the tail leads into the cockpit.

Two Ways In

  • Procedure 1: central screw, socket and cover, three screws, self-tailing arm, drum; bolt through with socket-head bolts (STBBB / STCCC: SH or HH).
  • Procedure 2: lever the skirt off with a screwdriver at the marked point, fit five M6 hex-head bolts, clip the skirt back and press it home. Not for STBBB / STCCC.
  • Make sure the skirt is correctly clipped onto the base.
  • Tools: medium flat screwdriver.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Keep the holes and drainage channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months. Replace worn parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs lightly. Never grease the pawls: excess grease near the pawls compromises safety.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Jaw screws (3) 4 Nm (35 in-lb)
Shaft screw and washer (pawl access) 4 Nm (35 in-lb)

If the jaws come apart, refit the peeler between them with the letters TOP facing up, and align the peeler with the stripper arm.

Radial 20 ST Spare Parts

From the Radial 20 STA parts list in the manual. STC uses drum S413550043; STCW uses white (W-suffix) skirt, jaws and cover; STBBB and STCCC have no skirt and use their own housing, drum, jaws, stripper arm and cover codes: check the PDF for your version. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A94136900 1 Assy housing winch 20 View part →
S413740085 1 Bushing Ø9ר11×9 Ask us to source it →
S413960085 1 Bushing Ø9ר11×12 View part →
S413720080 1 Bushing Ø55ר62×34 Ask us to source it →
S4137300B2 1 Washer Ø33.5ר58×5.5 View part →
S4137100A7 1 Bushing Ø28ר33×25 View part →
A94138600 2 Assy skirt winch 20 View part →
A94136700 3 Assy gear Z18 View part →
S418730080 3 Bushing Ø9ר11×7 Ask us to source it →
S000080003 4 Pawl Ø8 * View part →
S000380001 5 Pawl spring Ø8 * View part →
S413700004 6 Pin View part →
S413630002 7 Shaft winch 20 View part →
S268890080 9 Washer View part →
M0604003 10 Screw M6×12 UNI 5933 View part →
S413620041 11 Gear Z21 View part →
S4129400A0 12 Stripper arm support View part →
S413560053 13 Drum W20 View part →
S281670097 14 Red line View part →
A94136500 15 Assy jaws winch 20 Ask us to source it →
S413610080 15 Peeler W20–40 View part →
S385970001 15 Spring Ask us to source it →
M6009103 16 Screw UNI EN ISO 1207 M5×35 A4 View part →
S413570019 17 Stripper arm winch 20 View part →
M6007103 18 Screw M6×50 UNI 6107 View part →
S4135800A5 19 Cover 1 speed W20 View part →
A94136400 20 Assy socket W20–80 View part →
S415130085 20 Washer Ø7.7ר25×5.8 View part →
M0614303 20 Screw M8×20 UNI 6109 View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF come in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A94136900 Winch Spare for Radial & Performa Size 20 - Housing Assembly
S413960085 Winch Spare for Radial Size 35 to 40 - Bushing (9 x 11 x 12)
S4137300B2 Winch Spare for Radial & Performa Size 20 - Nylon Washer
S4137100A7 Winch Spare for Radial Size 20 - Bushing PTFE (28 x 33 x 35)
A94138600 Winch Spare for Radial & Performa Size 20 - Skirt Assembly
A94136700 Winch Spare for Radial Size 20 - Gear Assembly Z18
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S413700004 Winch Spare for Radial Size 20 - Pin
S413630002 Winch Spare for Radial & Performa Size 20 - Shaft
S268890080 Winch Spare for Radial Size 20 - Washer 32/40st (b26889)
M0604003 Winch Spare for Radial Size 20 - Screw (M6x12 UNI 5933)
S413620041 Winch Spare for Radial Size 20 - Gear Z21
S4129400A0 Winch Spare for Radial, Performa & Unipower Size 15 to 900 - Stripper arm support
S413560053 Winch Spare for Radial Size 20 - Aluminium Drum
S281670097 Winch Spare for Radial Size 15 to 20 - Red Line Ring (15-16-20)
S413610080 Winch Spare for Radial Size 20 to 40 - Peeler
M6009103 Winch Spare for Radial Size 20 - Screw (UNI EN ISO 1207:1996 - M5x35-A4)
S413570019 Winch Spare for Radial Size 15 to 20 - Stripper Arm
M6007103 Winch Spare for Radial Size 20 to 50 - Screw M6x50 UNI 6107
S4135800A5 Winch Spare for Radial & Performa Size 20 - Stripper Arm Cover
A94136400 Winch Spare for Radial Size 15 to 80 - Assembly Socket
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
S413550043 Winch Spare for Radial Size 20 - Chrome Drum
— Self Tailing Winch Radial Size 20 - Chrome / One Speed
— Self Tailing Winch Radial Size 20 - Bronze All / One Speed
— Self Tailing Winch Radial Size 20 - Aluminum Black / One Speed
— Self Tailing Winch Radial Size 20 - Chrome All / One Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual