INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, both deck-mounting routes, the strip-down and lubrication procedure, torques and the parts lists for every Radial 35.2 ST version (STA, STC, STCW, STBBB, STCCC).

DocumentHarken Radial 35.2 ST Winch Installation & Maintenance Manual
FormatPDF · 24 pages · 3.6 MB
LanguageEnglish
Radial 35.2 ST Winch

Specifications

Speed Power ratio Gear ratio
1st speed 13.50 : 1 2.13 : 1
2nd speed 35.90 : 1 5.65 : 1

The theoretical power ratio does not take friction into account.

Version Drum Weight
STA Anodized aluminium 3.6 kg
STC / STCW Chrome bronze / chrome-white 4.8 kg
STBBB / STCCC All bronze / all-chrome bronze 5.5 kg
Dimension mm
Base Ø 149
Top Ø 80.5
Height 170
Line entry height 80

Maximum working load (MWL): 650 kg (1433 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five M6 bolts through Ø6.2 mm holes on a Ø123 mm bolt circle (winch outside Ø149 mm).
  • Bolts are not supplied: use A4 stainless (DIN 267 part 11), sized for your deck. No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • STA, STC and STCW: an icon on the skirt marks the drive gear position.
  • Bed the holes in marine sealant, clean off the excess and keep the base drainage channels clear.
  • Position the self-tailing arm so the tail leads into the cockpit.

Two Ways In

  • Procedure 1: central screw, socket and cover, three screws, self-tailing arm (rotate and lift), drum; bolt through with socket-head bolts.
  • Procedure 2: lever the skirt off with a screwdriver at the marked point, fit five M6 hex-head bolts, clip the skirt back and press it home. Not for STBBB / STCCC.
  • Make sure the skirt is correctly clipped onto the base.
  • Tools: medium flat screwdriver.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Keep the holes and drainage channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months. Replace worn parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs lightly. Never grease the pawls: excess grease near the pawls compromises safety.
  • Washer n°12 may stay inside the drum support.
  • To free the pawls, press the spring against the pawl with a blade.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Drum support hex screws (6) 8 Nm (71 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)

If the jaws come apart, refit the peeler between them with the letters TOP facing up, and align the peeler with the stripper arm.

Radial 35.2 ST Spare Parts

From the Radial 35.2 STA parts list in the manual. STC uses drum S413170043; STCW uses white (W-suffix) skirt, jaws and cover; STBBB and STCCC have no skirt and use base A96633100 plus their own drum, jaws, stripper arm and cover codes: check the PDF for your version. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A94131000 1 Assy base winch 35 View part →
S413350080 1 Roller Ø6×19 Ask us to source it →
S4152300A7 1 Bushing Ø22ר25×9.5 View part →
S413960085 1 Bushing Ø9ר11×12 View part →
S413330085 1 Bushing Ø12ר14×11 View part →
A94131400 2 Assy skirt W35 View part →
S413020004 3 Gear Z12 View part →
S413030004 4 Pawls carrier Ø8×N2 View part →
S000080003 5 Pawl Ø8 * View part →
S000380001 6 Pawl spring Ø8 * View part →
S412830041 7 Gear Z23 View part →
S413000004 8 Pin Ø9×55 View part →
S279090002 9 Washer Ø36ר9.5×1 View part →
S415650004 10 Ratchet gear Z18 View part →
S412850041 11 Pinion Z13 View part →
S413120002 12 Washer Ø22.5ר45×1 View part →
S413070004 13 Pin Ø9ר12×32.5 View part →
A94130500 14 Assy gear Z20 View part →
S414900080 14 Bushing Ø12ר14×8 Ask us to source it →
A94131100 15 Assy housing winch 35 View part →
S414890080 15 Bushing Ø9ר11×7 View part →
S4130900A7 15 Bushing Ø22ר25×8.5 View part →
M0635103 16 Socket head screw M6×16 UNI 5931 View part →
S413150082 17 Washer Ø62ר80×1.5 View part →
A74136000 18 Bearing Ø56ר68×24 View part →
A94139000 19 Assy central shaft W35/40 View part →
S413880002 19 Washer Ø17.2ר32×1.5 View part →
S4129400A0 21 Stripper arm support View part →
S413160053 22 Drum W35 View part →
S281680097 23 Red line View part →
A94131800 24 Assy jaws winch 35 View part →
S413610080 24 Peeler W20–40 View part →
S385970001 24 Spring Ask us to source it →
M0601803 25 Screw UNI EN ISO 1207 M6×35 A4 View part →
S414200019 26 Stripper arm W35/40 View part →
M6007103 27 Screw M6×50 UNI 6107 View part →
A94136400 28 Assy socket W20–80 View part →
S415130085 28 Washer Ø7.7ר25×5.8 View part →
M0614303 28 Screw M8×20 UNI 6109 View part →
S4129500A5 29 Cover 2 speed W35 View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF come in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A94131000 Winch Spare for Radial Size 35 - Base Assembly
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S413960085 Winch Spare for Radial Size 35 to 40 - Bushing (9 x 11 x 12)
S413330085 Winch Spare for Radial Size 46 - Bushing (12 x 14 x 11)
A94131400 Winch Spare for Radial Size 35 - Skirt Assembly
S413020004 Winch Spare for Radial Size 35 to 50 - Gear Z12
S413030004 Winch Spare for Radial Size 35 to 70 - Pawls Carrier (8xn2)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S412830041 Winch Spare for Radial Size 35 to 46 - Gear Radial Z23
S413000004 Winch Spare for Radial Size 35 to 40 - Pin
S279090002 Winch Spare for Radial Size 35 to 40 - Washer (36x9
S415650004 Winch Spare for Radial Size 35 - Ratchet Gear Z18
S412850041 Winch Spare for Radial Size 35 to 40 - Pinion - Z13
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S413070004 Winch Spare for Radial Size 35 to 50 - Pin
A94130500 Winch Spare for Radial Size 35 to 40 - Gear Assembly Z20
A94131100 Winch Spare for Radial & Performa Size 35 - Housing Assembly
S414890080 Winch Spare for Radial Size 35 to 40 - Bushing Housing (9 x 11 x 7)
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
M0635103 Winch Spare for Radial Size 35 to 40 - Socket Head Screw M6x16 Uni 5931
S413150082 Winch Spare for Radial & Performa Size 35 to 40 - Washer (62x80x1.5)
A74136000 Winch Spare for Radial & Performa Size 60 to 70 - Needle Roller Bearing (56 x 68 x 24)
A94139000 Winch Spare for Radial & Performa Size 35 to 40 - Central Shaft Assembly
S413880002 Winch Spare for Radial Size 35 to 50 - Center Shaft Washer
S4129400A0 Winch Spare for Radial, Performa & Unipower Size 15 to 900 - Stripper arm support
S413160053 Winch Spare for Radial Size 35 - Aluminium Drum
S281680097 Winch Spare for Radial Size 35 to 40 - Ring Red Line 32 (B28169)
A94131800 Winch Spare for Radial & Performa Size 40 - Jaw Assembly
S413610080 Winch Spare for Radial Size 20 to 40 - Peeler
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
S414200019 Winch Spare for Radial Size 35 to 40 - Stripper arm
M6007103 Winch Spare for Radial Size 20 to 50 - Screw M6x50 UNI 6107
A94136400 Winch Spare for Radial Size 15 to 80 - Assembly Socket
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
S4129500A5 Winch Spare for Radial & Performa Size 35 - Stripper Arm Cover
S413170043 Winch Spare for Radial Size 35 - Chrome Drum
A94131400W Winch Spare for Radial Size 35 - White Skirt Assembly
A96633100 Winch Spare for Performa Size 35 - Base Assembly
— Self Tailing Winch Radial Size 35 - Bronze All / Two Speed
— Self Tailing Winch Radial Size 35 - Chrome / Two Speed
— Self Tailing Winch Radial Size 35 - Aluminum Black / Two Speed
— Self Tailing Winch Radial Size 35 - Chrome All / Two Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual