INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, deck mounting, the full strip-down and service procedure, and the parts list for every Radial 40.2 ST version (STA, STC, STCW, STBBB, STCCC).

DocumentHarken Radial 40.2 ST Winch Installation & Maintenance Manual
FormatPDF · 24 pages · 3.7 MB
LanguageEnglish
Radial 40.2 ST Winch

Specifications

1st speed 2nd speed
Gear ratio 2.13 : 1 6.28 : 1
Power ratio 13.50 : 1 39.90 : 1

The theoretical power ratio does not take friction into account.

Version Drum Weight
STA Anodized aluminium 3.8 kg
STC / STCW Chrome bronze / chrome-white 5.4 kg
STBBB / STCCC All bronze / all-chrome bronze 6.2 kg
Dimension mm
Base Ø 156
Top Ø 80.5
Height 175
Line entry height 82

Maximum working load (MWL): 850 kg (1874 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Mount on a flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five M6 bolts through Ø6.2 mm holes on a Ø123 mm bolt circle. Bolts are not supplied.
  • Use A4 stainless bolts only (DIN 267 part 11). Do not use countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Bed the holes in marine sealant and keep the base drain channels clear.

Two Ways In

  • Procedure 1: remove the drum and bolt through with socket-head bolts.
  • Procedure 2: unclip the skirt and use M6 hex-head bolts (not for STBBB / STCCC).
  • Position the self-tailing arm so the tail leads into the cockpit.
  • A drilling template is available from Harken.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, pins and teeth lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Housing hex screws (6) 8 Nm (71 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)

When refitting the jaws, the peeler goes between them with the letters TOP facing up. Check each pawl opens and closes easily with a finger.

Radial 40.2 ST Spare Parts

From the STA / STC parts list in the manual. STCW (white), STBBB and STCCC use different skirt, drum, jaws, stripper arm and cover codes: check the PDF for your version. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A94141300 1 Winch 40 base assembly View part →
A94141400 2 Skirt assembly W40 (STA, STC) View part →
S413020004 3 Gear Z12 View part →
S413030004 4 Pawl carrier Ø8 × N2 View part →
S000080003 5 Pawl Ø8 * View part →
S000380001 6 Pawl spring Ø8 * View part →
S412830041 7 Gear Z23 View part →
S413000004 8 Pin Ø9 × 55 View part →
S279090002 9 Washer Ø36 × Ø9.5 × 1 View part →
S412970004 10 Gear Z20 View part →
S412850041 11 Pinion Z13 View part →
S413120002 12 Washer Ø22.5 × Ø45 × 1 View part →
S413070004 13 Pin Ø9 × Ø12 × 32.5 View part →
A94130500 14 Gear Z20 assembly View part →
A94141500 15 Housing assembly W40 View part →
M0635103 16 Socket head screw M6 × 16 UNI 5931 View part →
S413150082 17 Washer Ø62 × Ø80 × 1.5 View part →
A74136000 18 Bearing Ø56 × Ø68 × 24 View part →
A94139000 19 Central shaft assembly W35/40 View part →
S4129400A0 21 Stripper arm housing View part →
S414170053 22 Drum W40, anodized aluminium (STA) View part →
S414180043 22 Drum W40 C, chrome bronze (STC / STCW) View part →
S281680097 23 Red line View part →
A94131800 24 Jaws assembly W40 View part →
S413610080 24 Peeler W20–40 View part →
S385970001 24 Spring (jaws) Ask us to source it →
M0601803 25 Screw UNI EN ISO 1207 M6 × 35 A4 View part →
S414200019 26 Stripper arm W35/40 View part →
M6007103 27 Screw M6 × 50 UNI 6107 View part →
A94136400 28 Socket assembly W20–80 View part →
S4141900A5 29 Cover 2-speed W40 View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked with an asterisk in the PDF (pawls and pawl springs) are supplied in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A94141300 Winch Spare for Radial Size 40 - Base Assembly
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S413960085 Winch Spare for Radial Size 35 to 40 - Bushing (9 x 11 x 12)
S413330085 Winch Spare for Radial Size 46 - Bushing (12 x 14 x 11)
A94141400 Winch Spare for Radial Size 40 - Skirt
S413020004 Winch Spare for Radial Size 35 to 50 - Gear Z12
S413030004 Winch Spare for Radial Size 35 to 70 - Pawls Carrier (8xn2)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S412830041 Winch Spare for Radial Size 35 to 46 - Gear Radial Z23
S413000004 Winch Spare for Radial Size 35 to 40 - Pin
S279090002 Winch Spare for Radial Size 35 to 40 - Washer (36x9
S412970004 Winch Spare for Radial Size 40 - Gear Z20
S412850041 Winch Spare for Radial Size 35 to 40 - Pinion - Z13
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S413070004 Winch Spare for Radial Size 35 to 50 - Pin
A94130500 Winch Spare for Radial Size 35 to 40 - Gear Assembly Z20
A94141500 Winch Spare for Radial & Performa Size 40 - Housing Assembly
S414890080 Winch Spare for Radial Size 35 to 40 - Bushing Housing (9 x 11 x 7)
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
M0635103 Winch Spare for Radial Size 35 to 40 - Socket Head Screw M6x16 Uni 5931
S413150082 Winch Spare for Radial & Performa Size 35 to 40 - Washer (62x80x1.5)
A74136000 Winch Spare for Radial & Performa Size 60 to 70 - Needle Roller Bearing (56 x 68 x 24)
A94139000 Winch Spare for Radial & Performa Size 35 to 40 - Central Shaft Assembly
S413880002 Winch Spare for Radial Size 35 to 50 - Center Shaft Washer
S4129400A0 Winch Spare for Radial, Performa & Unipower Size 15 to 900 - Stripper arm support
S414170053 Winch Spare for Radial Size 40 - Aluminium Drum
S281680097 Winch Spare for Radial Size 35 to 40 - Ring Red Line 32 (B28169)
A94131800 Winch Spare for Radial & Performa Size 40 - Jaw Assembly
S413610080 Winch Spare for Radial Size 20 to 40 - Peeler
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
S414200019 Winch Spare for Radial Size 35 to 40 - Stripper arm
M6007103 Winch Spare for Radial Size 20 to 50 - Screw M6x50 UNI 6107
A94136400 Winch Spare for Radial Size 15 to 80 - Assembly Socket
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
S4141900A5 Winch Spare for Radial & Performa Size 40 - Stripper Arm Cover
S414180043 Winch Spare for Radial Size 40 - Chrome Drum
A96633200 Winch Spare for Performa Size 40 - Base Assembly
A94149300 Winch Spare for Electric Size 35 to 80 - Socket Assembly
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
A94194900 Winch Spare for Radial Size 50 to 70 - Gear BoxVF49
A94149200 Winch Spare for Electric Size 35 to 70 - Electric Motor Flange Assembly
A94149500 Winch Spare for Electric Size 40 to 46 - Support Flange Gear Box Short
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
A94161600 Winch Spare for Electric Size 40 to 46 - Shaft Assembly 43mm Horizontal Gear Box
A96015400 Winch Spare for Electric Size 35 to 40 - Electric Motor Kit - 12V 0.7Kw
A96015700 Winch Spare for Electric Size 40 - Electric Motor Kit - 24V 0.9Kw
— Load Controller for Radial Winch Size 40 - 12V
— Load Controller for Radial Winch Size 40 - 24V
— Self Tailing Winch Radial Size 40 - Aluminum Black / Two Speed
— Self Tailing Winch Radial Size 40 - Chrome / Two Speed
— Self Tailing Winch Radial Size 40 - Bronze All / Two Speed
— Self Tailing Winch Radial Size 40 - Chrome All / Two Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual