INSTALLATION & MAINTENANCE MANUAL

Ratios, line speeds and loads, current draw, outline, both deck-mounting routes, motor installation, wiring, servicing and the parts and motor-kit lists for the Radial 40 Rewind electric winch.

DocumentHarken Radial 40 Rewind Winch Installation & Maintenance Manual
FormatPDF · 27 pages · 5.1 MB
LanguageEnglish
Radial 40 Rewind Winch

Specifications

Speed Power ratio Gear ratio
1st speed 13.5 : 1 2.13 : 1
2nd speed 39.9 : 1 6.28 : 1

The theoretical power ratio does not take friction into account.

Horizontal motor (no-load line speed / max load) 1st speed 2nd speed
12 V 21 m/min / 300 kg 7.1 m/min / 850 kg
24 V 21 m/min / 300 kg 7.1 m/min / 850 kg
Motor Nominal power Current at MWL
12 V 700 W 175 A
24 V 900 W 88 A
Version Drum Weight
ST A Anodized aluminium 15 kg
ST C Chromed 16 kg
Dimension mm
Base Ø 157
Drum Ø 77
Line entry height 82
Below-deck depth 180
Deck to top of motor 41
Below-deck horizontal extent (drawing) 282 + 78

Maximum working load (MWL): 850 kg. Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five M6 bolts through Ø6.2 mm holes on a Ø123 mm bolt circle, plus a Ø80 mm cut-out (winch outside Ø157 mm).
  • Bolts are not supplied: use A4 stainless (DIN 267 part 11), sized for your deck. No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • An icon on the skirt marks the drive gear position.
  • Before drilling, check there is room below deck: the motor can be coupled in any of four positions 60° apart.
  • Bed the holes in marine sealant, clean off the excess and keep the base drainage channels clear.
  • Position the self-tailing arm so the tail leads into the cockpit.

Two Ways In

  • Set the knob to the Rewind position before starting.
  • Procedure 1 (SH bolts): pull out the disconnect rod, central screw, socket and cover (mind the o-ring), three screws, stripper arm, drum. Tools: flat screwdriver, 6 mm and 3 mm hex keys.
  • Procedure 2 (HH bolts): remove the knob screw and knob, lever off the skirt, remove the stripper arm and drum, fit five M6 hex-head bolts, clip the skirt back and refit the knob in the Rewind position.
  • Make sure the skirt is correctly clipped onto the base.

Motor and Electrical

Fitting the drive

  • Position the flange and tighten the six screws to 8 Nm (71 in-lb); check the seal is seated.
  • Position the reduction gear and motor and tighten the two screws to 8 Nm (71 in-lb), keeping the flange aligned.
  • Tools: 5 mm hex key, two 13 mm wrenches.
  • Test the powered winch before sailing.

Wiring

  • Electric control box (solenoids) on a bulkhead, remote circuit breaker between supply and control box, push-buttons on deck where they are easy to use.
  • Motor terminals: Nut – cable terminal – self-locking washer – lock nut. Hold the inner nut with one spanner, tighten with a second, never turn the central spindles. Torque 10 Nm (88 in-lb), no more.
Winch Voltage Under 5 m (16.4 ft) 5–10 m (16.4–32.8 ft) 10–15 m (32.8–49.2 ft) 15–20 m (49.2–65.6 ft)
40 Rewind 12 V AWG 2 / 32 mm² AWG 0 / 50 mm² AWG 00 / 70 mm² AWG 000 / 95 mm²
40 Rewind 24 V AWG 5 / 16 mm² AWG 3 / 25 mm² AWG 2 / 35 mm² AWG 0 / 50 mm²

Switch the power off before installing or servicing the winch.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Keep the holes and drainage channels in the base clear so water cannot collect.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months. Replace worn parts with original Harken parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, brush, rags.
  • Soak metal parts in a basin of diesel oil; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs lightly. Never grease the pawls: excess grease near the pawls compromises safety.
  • Mind the springs when removing the pawls carrier and the spacer.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Stripper arm screws (3) 4 Nm (35 in-lb)
Knob screw 0.5 Nm (4.42 in-lb)
Drum support hex screws 20 Nm (177 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)
Motor flange and motor screws 8 Nm (71 in-lb)
Motor terminals 10 Nm (88 in-lb)

Refit the disconnect rod with its groove at the bottom, and check the o-ring in the socket before refitting the central screw.

Radial 40 Rewind Spare Parts

From the 40 Rewind STA EL parts list in the manual. STC uses drum S664050043; STCW also uses white (W-suffix) skirt, cover and upper jaw. Parts marked * come in the Harken service kit.

Harken code Pos. Description
A663960053 1 Base W40 Ask us to source it →
M0649802 2 Heli-coil M6×9 Ask us to source it →
S4130900A7 3 Bushing Ø22ר25×8.5 * View part →
S413960085 4 Bushing Ø9ר11×12 * View part →
S413330085 5 Bushing Ø12ר14×11 * View part →
M6009463 6 Spring loaded ball plunger Ø6 Ask us to source it →
S664020052 7 Spacer Ask us to source it →
M0615102 8 Heli-coil M6×6 Ask us to source it →
S413350080 9 Roller Ø6×19 Ask us to source it →
S6640100A5 10 Skirt W40 Rewind Ask us to source it →
S000080003 12 Pawl Ø8 View part →
S000380001 13 Pawl spring Ø8 View part →
S413000004 14 Pin Ø9×55 View part →
S279090002 15 Washer 36×9.5×1 * View part →
S412970004 16 Gear Z20 View part →
S412850041 17 Pinion Z13 View part →
S413070004 18 Pin Ø9-Ø12×32.5 View part →
S663990004 19 Gear Z20 Ask us to source it →
S414900080 20 Bushing Ø12ר14×8 * Ask us to source it →
S663970053 21 Support W40 Rewind Ask us to source it →
S414890080 22 Bushing Ø9ר11×7 * View part →
M0635103 23 Socket head screw M6×16 UNI 5931 * View part →
S413150082 24 Washer Ø62ר80×1.5 * View part →
A74136000 25 Bearing Ø56ר68×24 * View part →
S4129400A0 27 Stripper arm support View part →
S281680097 28 Red line * View part →
M0601803 29 Screw UNI EN ISO 1207 M6×35 A4 * View part →
M6007103 30 Screw M6×50 UNI 6107 * View part →
S6640300A5 31 Cover 2 speed W40 Rewind Ask us to source it →
S663910019 32 Stripper arm W40 Rewind Ask us to source it →
S663920019 33 Peeler W40 Rewind Ask us to source it →
S419170080 34 Slider Ask us to source it →
S416570001 35 Spring stripper arm W46 Rewind Ask us to source it →
S416580041 36 Bushing Ask us to source it →
M0619003 37 Screw M5×20 UNI 6109 Ask us to source it →
A74165000 38 Command W46 Rewind (fork, bushing) Ask us to source it →
S664000080 39 Knob W40 Rewind Ask us to source it →
S419200041 41 Bushing Ø6.5ר4×3 Ask us to source it →
M600850002 42 Heli-coil M4×8 Ask us to source it →
S497400080 43 Knob W46 Rewind Ask us to source it →
S416520019 44 Socket handle W46 Rewind Ask us to source it →
S414940085 45 Washer Ø25ר15×4 View part →
S414930003 46 Nut screw for disconnect rod View part →
M0679797 47 O-ring RC 2025 series View part →
M0624103 48 Screw M4×16 UNI 5931 View part →
S418590001 49 Spring Ø10.67×12.7 Ask us to source it →
S416530004 50 Pin for switch W46 Rewind Ask us to source it →
M0624203 51 Screw M6×30 Ask us to source it →
S663950004 52 Main shaft W40 Rewind Ask us to source it →
S663980002 53 Disconnect rod 40 Rewind Ask us to source it →
S416240041 54 Gear Z23 Ask us to source it →
S664060004 55 Pawls carrier Ø8×N2 W40.2 Rewind Ask us to source it →
S416260041 56 Disconnect flange Ask us to source it →
M0614103 57 Ball 5-16" inox Ask us to source it →
M0616603 58 Seeger ring UNI 7435 Ø28 Ask us to source it →
M0630802 59 Smalley ring SSR0137-S17 Ask us to source it →
S663930053 60 Drum A W40 Rewind Ask us to source it →
S663940053 61 Lower jaw W40 Rewind Ask us to source it →
S4131900A8 62 Upper jaw W40 Ask us to source it →
S385970001 63 Spring Ask us to source it →

Motor and drive kits

Harken code Drive Description
A93127900 Horizontal KIT gear reduction VF49 (right-hand motor) Ask us to source it →
A94194900 Horizontal KIT LM gear reduction VF49 (left-hand motor) View part →
A94149200 Horizontal KIT assy electric motor flange View part →
A94149500 Horizontal KIT EL HO motor flange View part →
A94161600 Horizontal KIT EL HO motor clutch View part →
A96024100 12 V Motor 12 V 0.7 kW with brake Ask us to source it →
A96033800 24 V Motor 24 V 0.7 kW with brake Ask us to source it →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF come in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
S279090002 Winch Spare for Radial Size 35 to 40 - Washer (36x9
S414890080 Winch Spare for Radial Size 35 to 40 - Bushing Housing (9 x 11 x 7)
M0635103 Winch Spare for Radial Size 35 to 40 - Socket Head Screw M6x16 Uni 5931
A74136000 Winch Spare for Radial & Performa Size 60 to 70 - Needle Roller Bearing (56 x 68 x 24)
S281680097 Winch Spare for Radial Size 35 to 40 - Ring Red Line 32 (B28169)
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
M6007103 Winch Spare for Radial Size 20 to 50 - Screw M6x50 UNI 6107
M0624103 Winch Spare for Electric Size 46 to 60 - Screw M4 x 16
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
S413960085 Winch Spare for Radial Size 35 to 40 - Bushing (9 x 11 x 12)
S413330085 Winch Spare for Radial Size 46 - Bushing (12 x 14 x 11)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S413000004 Winch Spare for Radial Size 35 to 40 - Pin
S412970004 Winch Spare for Radial Size 40 - Gear Z20
S412850041 Winch Spare for Radial Size 35 to 40 - Pinion - Z13
S413070004 Winch Spare for Radial Size 35 to 50 - Pin
S413150082 Winch Spare for Radial & Performa Size 35 to 40 - Washer (62x80x1.5)
S4129400A0 Winch Spare for Radial, Performa & Unipower Size 15 to 900 - Stripper arm support
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
A94194900 Winch Spare for Radial Size 50 to 70 - Gear BoxVF49
A94149200 Winch Spare for Electric Size 35 to 70 - Electric Motor Flange Assembly
A94149500 Winch Spare for Electric Size 40 to 46 - Support Flange Gear Box Short
M6015697 Winch Spare for Radial Size 60 to 70 - O Ring (5 x 5 x 1 Orm 0055)
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
A94161600 Winch Spare for Electric Size 40 to 46 - Shaft Assembly 43mm Horizontal Gear Box
— Electric Winch Rewind Size 40 - 12V / Aluminum Black / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 12V / Aluminum Black / Two Speed / Right Mount
— Electric Winch Rewind Size 40 - 24V / Aluminum Black / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 12V / Bronze All / Two Speed / Right Mount
— Electric Winch Rewind Size 40 - 12V / Chrome / Two Speed / Right Mount
— Electric Winch Rewind Size 40 - 12V / Chrome / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 24V / Aluminum Black / Two Speed / Right Mount
— Electric Winch Rewind Size 40 - 24V / Chrome / Two Speed / Right Mount
— Electric Winch Rewind Size 40 - 24V / Bronze All / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 24V / Bronze All / Two Speed / Right Mount
— Electric Winch Rewind Size 40 - 24V / Chrome / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 12V / Bronze All / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 24V / Chrome All / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 12V / Chrome All / Two Speed / Left Mount
— Electric Winch Rewind Size 40 - 12V / Chrome All / Two Speed / Right Mount
— Electric Winch Rewind Size 40 - 24V / Chrome All / Two Speed / Right Mount

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual