INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, performance, dimensions, deck and motor installation, wire sizing, service torques and the parts list for the Radial 46 Rewind electric winch.

DocumentHarken Radial 46 Rewind Winch Installation & Maintenance Manual
FormatPDF · 28 pages · 4.8 MB
LanguageEnglish
Radial 46 Rewind Winch

Specifications

Power ratio Gear ratio
1st speed 11.70 : 1 2.30 : 1
2nd speed 46.50 : 1 9.17 : 1

The theoretical power ratio does not take friction into account.

Version Weight
ST A 16 kg
ST C / CW 19 kg
ST BBB / CCC 19.7 kg

A = anodized aluminium drum; C = chrome bronze drum; CW = chrome/white; BBB = all bronze; CCC = all-chrome bronze.

Dimension (outline drawing) mm
Base Ø 192
Height 203
Drum Ø 100
Line entry height 91
Depth below deck 156
Horizontal motor span (either side of winch axis) 282 / 92
E (deck to motor) 41 or 67 (see motor pages in the PDF)

Maximum working load (MWL) of the 46 Rewind: 1300 kg (2866 lb). Loads above the MWL can make the winch fail or pull off the deck suddenly.

Performance Data

Motor 1st speed line speed 2nd speed line speed 1st speed max load 2nd speed max load
Horizontal 12V (700 W) 25.5 m/min 6.5 m/min 315 kg 1300 kg
Horizontal 24V (700 W) 25.5 m/min 6.5 m/min 315 kg 1300 kg

Line speed measured with no load.

Motor Nominal power Current at MWL
Horizontal 12V 700 W 205 A
Horizontal 24V 700 W 100 A

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five Ø8.5 mm holes on a Ø150 mm bolt circle plus an Ø80 mm cut-out for the motor; five M8 bolts (not supplied by Harken).
  • A4 stainless bolts only (DIN 267 part 11). No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Fill the holes with marine sealant and keep the base drain channels clear.
  • The drilling template also marks the knob orientation (80°, Rewind winch only).
  • Check below deck for the flange and motor before drilling.

Getting to the Base

  • Before starting, set the Rewind knob to the position shown in the PDF.
  • Procedure 1: pull out the disconnect rod; unscrew the central screw, 2 Nm (18 in-lb); slide off socket and cover (mind the o-ring); remove the three screws, 4 Nm (35 in-lb).
  • Procedure 2 (hex-head bolts): remove the knob screw, 0.5 Nm (4.42 in-lb), and the knob; unclip the skirt; lift off the stripper arm and the drum; fit five M8 hex-head bolts; clip the skirt back and set the knob back in the Rewind position.
  • STA, STC, STCW: socket-head bolts. STBBB, STCCC: socket-head or hex-head bolts.
  • Tools: medium flat screwdriver, 6 mm and 3 mm hex keys. Position the self-tailing arm so the tail leads into the cockpit.

Motor and Electrical

Motor Installation

  • Switch off the power before installing or servicing the winch.
  • The motor can be coupled to the winch in different positions: check the space below deck first.
  • Flange: six M6 precote-coated screws, 8 Nm (71 in-lb). Check the seal is seated correctly.
  • Reduction gear and motor: two screws, 8 Nm (71 in-lb); align the flange.
  • Tools: 5 mm hex key, two 13 mm wrenches.
  • Test the powered winch before sailing.

Electrical

  • The Harken Dual Function Control Box is mandatory for every model; follow its own manual for wiring.
  • Cable terminals go between nut and lock nut; hold the nut with one spanner, tighten with a second, never turn the central spindle.
  • Terminal torque no greater than 10 Nm (88 in-lb).
  • Contact sequence: nut – cable terminal – self-locking washer – lock nut.

Wire size (total distance winch–battery)

Voltage Under 5 m (16.4 ft) 5–10 m (16.4–32.8 ft) 10–15 m (32.8–49.2 ft) 15–20 m (49.2–65.6 ft)
12V AWG 2 / 32 mm² AWG 0 / 50 mm² AWG 00 / 70 mm² AWG 000 / 95 mm²
24V AWG 5 / 16 mm² AWG 3 / 25 mm² AWG 2 / 35 mm² AWG 0 / 50 mm²

Control box (HCP)

Winch / voltage HCP model Ampere rating
46 Rewind – 12V HCP1717 80A
46 Rewind – 24V HCP1717 80A

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months; replace worn parts with original parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, brush, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, pins and teeth lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls: excess grease on the pawls compromises safety.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Knob screw 0.5 Nm (4.42 in-lb)
Housing hex screws (5) 20 Nm (177 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)
Motor flange screws (6) 8 Nm (71 in-lb)
Motor terminals max 10 Nm (88 in-lb)

Switch off the power first. When removing gear n°27 watch the springs; when sliding out the command group watch the two balls. Refit the disconnect rod with its groove in the lower part, and grease the socket o-ring before the central screw.

Radial 46 Rewind Spare Parts

From the STA EL parts list in the manual. Parts marked * come in the Harken service kit. Multi-part assemblies are listed by assembly code; sub-part codes are in the PDF.

Harken code Pos. Description
A94164101 1 W46 RW base assembly Ask us to source it →
A94164200 2 Skirt assembly Winch 46 Rewind View part →
S413300004 3 Pin Ø12 × 60 View part →
S278170002 4 Washer Ø12.5 × Ø48 × 1.5 View part →
S000080003 5 Pawl Ø8 * View part →
S000380001 6 Pawl spring Ø8 * View part →
S413250041 7 Pinion Z13 View part →
M6017694 8 Bushing PSM-1214-20 Ask us to source it →
S413070004 9 Pin Ø9 × Ø12 × 32.5 View part →
A94133400 10 Gear Z12 assembly View part →
A96756700 11 W46 RW housing assembly Ask us to source it →
M0606303 12 Screw M8 × 25 UNI 5931 View part →
A74133700 13 Bearing Ø75 × Ø87 × 26 View part →
S413390080 14 Spacer View part →
S4129400A0 16 Stripper arm support View part →
S281690097 17 Red line View part →
M0601803 18 Screw UNI EN ISO 1207 M6 × 35 A4 View part →
M6007103 19 Screw M6 × 50 UNI 6107 View part →
S416540004 20 Gear Z27 Ask us to source it →
S416280004 21 Main shaft W46 Rewind Ask us to source it →
S416260041 22 Disconnect flange Ask us to source it →
M0614103 23 Ball 5-16" stainless Ask us to source it →
M0616603 24 Retaining ring UNI 7435 Ø28 Ask us to source it →
M0630802 25 Elastic ring SSR0137-S17 Ask us to source it →
S416250004 26 Pawl carrier Ø8 × N2 Ask us to source it →
S416240041 27 Gear Z23 Ask us to source it →
S416300002 28 Disconnect rod 46 Rewind Ask us to source it →
S416530004 29 Pin for switch Ask us to source it →
M0624203 30 Screw M6 × 30 Ask us to source it →
S418590001 31 Spring Ø10.67 × 12.7 Ask us to source it →
A74165000 32 Command, W46 Rewind Ask us to source it →
S416480053 33 Drum W46 Rewind Ask us to source it →
A94191800 34 Knob assembly W46 Rewind Ask us to source it →
S497400180 35 Knob Rewind Ask us to source it →
M0624103 36 Screw M4 × 16 UNI 5931 View part →
A94165200 37 Socket assembly Rewind Ask us to source it →
S6511900A5 38 Cover W46 Rewind Ask us to source it →
A94192100 39 Jaws assembly Winch 46 Rewind Ask us to source it →
A74165500 40 Stripper arm Winch 46 Rewind C Ask us to source it →

Codes that change by version

Harken code Version Description
S653520043 STC / STCW / STCCC Drum 46 C Rewind Ask us to source it →
A94164200W STCW Skirt assembly Winch 46 Rewind RAL9003 Ask us to source it →
S6511900A5W STCW Cover 2-speed W46 RW RAL 9003 Ask us to source it →
A94192100W STCW Jaws assembly Winch 46 STCW Rewind Ask us to source it →
A96938300 STBBB Skirt assembly Winch 46 BBB Rewind Ask us to source it →
S693840043 STBBB Drum W46 BBB Rewind Ask us to source it →
A76938800 STBBB Cover W46 BBB Rewind Ask us to source it →
A96938500 STBBB Jaws assembly Winch 46 BBB Rewind Ask us to source it →
A76938600 STBBB Stripper arm Winch 46 BBB Rewind Ask us to source it →
A96938000 STCCC Skirt assembly Winch 46 CCC Rewind Ask us to source it →
A76938200 STCCC Cover W46 CCC Rewind Ask us to source it →
A96938100 STCCC Jaws assembly Winch 46 CCC Rewind Ask us to source it →

Motor and drive kits

Part no. Description
A93127900 Gear reduction kit 1/24 Ask us to source it →
A94194900 LM gear reduction kit 1/24 View part →
A94149200 Electric motor flange kit View part →
A94149200L Electric motor flange kit, left Ask us to source it →
A94149500 Horizontal motor flange kit View part →
A94161600 Horizontal motor clutch kit View part →
A96024100 Electric motor kit 12V 0.7 kW Ask us to source it →
A96033800 Electric motor kit 24V 0.7 kW (with brake on the 24V H82 version) Ask us to source it →
A94966500 Horizontal motor flange kit (H82) View part →
A94952400 Horizontal motor clutch kit (24V H82) View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF (pawls and pawl springs) are supplied in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
HCP1717 Winch Circuit Breaker - 80 Amp 12V/24V
S414890080 Winch Spare for Radial Size 35 to 40 - Bushing Housing (9 x 11 x 7)
S413330085 Winch Spare for Radial Size 46 - Bushing (12 x 14 x 11)
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
A94164200 Winch Spare for Radial Rewind Size 46 - Skirt Assembly
S413300004 Winch Spare for Radial Size 46 - Pin (12x60)
S278170002 Winch Spare for Radial Size 46 to 70 - Washer (12.5 x 48 x 1.5)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S413250041 Winch Spare for Radial Size 46 - Pinion - Z13
S413070004 Winch Spare for Radial Size 35 to 50 - Pin
A94133400 Winch Spare for Radial Size 46 - Assy Gear Z12
M0606303 Winch Spare for Radial Size 46 to 70 - Screw (M8x25 UNI 5931)
A74133700 Winch Spare for Radial & Performa Size 35 to 40 - Bearing Cage (75 x 87 x 26)
S413390080 Winch Spare for Radial Size 46 - Spacer
S4129400A0 Winch Spare for Radial, Performa & Unipower Size 15 to 900 - Stripper arm support
S281690097 Winch Spare for Radial Size 40 to 50 - Ring Red Line (B28169)
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
M6007103 Winch Spare for Radial Size 20 to 50 - Screw M6x50 UNI 6107
M0624103 Winch Spare for Electric Size 46 to 60 - Screw M4 x 16
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
A94194900 Winch Spare for Radial Size 50 to 70 - Gear BoxVF49
A94149200 Winch Spare for Electric Size 35 to 70 - Electric Motor Flange Assembly
A94149500 Winch Spare for Electric Size 40 to 46 - Support Flange Gear Box Short
M6015697 Winch Spare for Radial Size 60 to 70 - O Ring (5 x 5 x 1 Orm 0055)
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
A94161600 Winch Spare for Electric Size 40 to 46 - Shaft Assembly 43mm Horizontal Gear Box
A94966500 Winch Spare for Electric Size 50 to 70 - Support Flange Gear Box Tall
A94952400 Winch Spare for Electric Size 50 to 70 - Motor Clutch - Horizontal (E=69 mm)
— Electric Winch Rewind Size 46 - 12V / Aluminum Black / Two Speed / Right Mount
— Electric Winch Rewind Size 46 - 24V / Aluminum Black / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 12V / Bronze All / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 24V / Aluminum Black / Two Speed / Right Mount
— Electric Winch Rewind Size 46 - 12V / Chrome / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 12V / Aluminum Black / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 12V / Chrome / Two Speed / Right Mount
— Electric Winch Rewind Size 46 - 24V / Bronze All / Two Speed / Right Mount
— Electric Winch Rewind Size 46 - 24V / Chrome / Two Speed / Right Mount
— Electric Winch Rewind Size 46 - 12V / Bronze All / Two Speed / Right Mount
— Electric Winch Rewind Size 46 - 24V / Bronze All / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 24V / Chrome / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 24V / Chrome All / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 12V / Chrome All / Two Speed / Left Mount
— Electric Winch Rewind Size 46 - 24V / Chrome All / Two Speed / Right Mount
— Electric Winch Rewind Size 46 - 12V / Chrome All / Two Speed / Right Mount

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual