INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, dimensions, both deck-mounting procedures, service torques and the parts list for every Radial 50.2 ST version (STA, STC, STCW, STBBB, STCCC).

DocumentHarken Radial 50.2 ST Winch Installation & Maintenance Manual
FormatPDF · 24 pages · 3.8 MB
LanguageEnglish
Radial 50.2 ST Winch

Specifications

Power ratio Gear ratio
1st speed 10.90 : 1 2.40 : 1
2nd speed 50.40 : 1 10.90 : 1

The theoretical power ratio does not take friction into account.

Version Weight
STA 6.0 kg
STC / STCW 9.2 kg
STBBB / STCCC 10.4 kg

A = anodized aluminium drum; C = chrome bronze drum; CW = chrome/white; BBB = all bronze; CCC = all-chrome bronze.

Dimension mm
Height 212.4
Drum Ø 111
Line entry height 96
Base Ø 194

Maximum working load (MWL) of the Radial 50.2 ST: 1450 kg (3197 lb). Loads above the MWL can make the winch fail or pull off the deck suddenly.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Five Ø8.2 mm holes on a Ø150 mm bolt circle; five M8 bolts (not supplied by Harken).
  • A4 stainless bolts only (DIN 267 part 11). No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Fill the holes with marine sealant and keep the base drain channels clear.

Getting to the Base

  • Socket-head bolts: unscrew the central screw, 2 Nm (18 in-lb); slide off socket and cover; remove the three screws, 4 Nm (35 in-lb); rotate and lift off the self-tailing arm; lift off the drum.
  • Hex-head bolts (not for BBB / CCC): unclip the skirt with a screwdriver, fit five M8 hex-head bolts, then press the skirt back until it clips onto the base.
  • Position the self-tailing arm so the tail leads into the cockpit.
  • A drilling cut-out template is available on harken.com.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months; replace worn parts with original parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, pins and teeth lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls: excess grease on the pawls compromises safety.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Housing hex screws (5) 20 Nm (177 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)

Grease the socket screw, the drum gear and the middle step of the housing assembly. Refit the peeler between the jaws with the letters TOP facing up and align it with the stripper arm. Check each pawl opens and closes with a finger.

Radial 50.2 ST Spare Parts

From the STA parts list in the manual. Parts marked * come in the Harken service kit. Multi-part assemblies are listed by assembly code; sub-part codes are in the PDF.

Harken code Pos. Description
A94134700 1 Base assembly Winch 50 View part →
A94134900 2 Skirt assembly Winch 50 View part →
S413020004 3 Gear Z12 View part →
S416050004 4 Pin View part →
S278170002 5 Washer Ø12.5 × Ø48 × 1.5 View part →
S412800041 6 Gear Z30 View part →
S414260004 7 Pawl carrier Ø8 × N2 View part →
S000080003 8 Pawl Ø8 * View part →
S000380001 9 Pawl spring Ø8 * View part →
S415590041 10 Gear Z20 View part →
S415610004 11 Pinion Z11 View part →
A72821800 12 Roller bearing 14/20/18 View part →
S281340080 13 Spacer, roller bearings View part →
S413120002 14 Washer Ø22.5 × Ø45 × 1 View part →
S413070004 15 Pin Ø9 × Ø12 × 32.5 View part →
A94156000 16 Gear Z11 assembly View part →
A94134800 17 Housing assembly Winch 50 View part →
M0606303 18 Screw M8 × 25 UNI 5931 View part →
A74135100 19 Bearing Ø85 × Ø97 × 26 View part →
S413520080 20 Spacer Ask us to source it →
A94142200 21 Central shaft assembly W50 View part →
S4129400A0 23 Stripper arm support View part →
S413400053 24 Drum W50 View part →
S281690097 25 Red line View part →
A94134300 26 Jaws assembly Winch 50 View part →
M0601803 27 Screw UNI EN ISO 1207 M6 × 35 A4 View part →
S413440019 28 Stripper arm W50 View part →
M6007103 29 Screw M6 × 50 UNI 6107 View part →
S4134500A5 30 Cover 2-speed W50 View part →
A94136400 31 Socket assembly W20–80 View part →

Codes that change by version

Other versions use different codes for the parts below; everything else matches the STA list. Check the PDF for your version.

Harken code Version Description
S413410043 STC / STCW Drum W50 C View part →
A94134900W STCW Skirt assembly Winch 50 RAL9003 Ask us to source it →
A94134300W STCW Jaws assembly Winch 50 (white) Ask us to source it →
S4134500A5W STCW Cover 2-speed W50 RAL9003 Ask us to source it →
A96633400 STBBB / STCCC Base assembly Winch 50 View part →
S688140043 STBBB Drum W50 B Ask us to source it →
A96933500 STBBB Jaws assembly Winch 50 BBB Ask us to source it →
S7123200F0 STBBB Stripper arm W50 BBB Ask us to source it →
A76933600 STBBB Cover W50 ST BBB Ask us to source it →
S681070043 STCCC Drum C W50 CCC Ask us to source it →
A96812100 STCCC Jaws assembly Winch 50 CCC Ask us to source it →
A76811400 STCCC Cover 2-speed W50 CCC Ask us to source it →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF (pawls and pawl springs) are supplied in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A94134700 Winch Spare for Radial Size 50 - Aluminium Base Assembly
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S414890080 Winch Spare for Radial Size 35 to 40 - Bushing Housing (9 x 11 x 7)
S413330085 Winch Spare for Radial Size 46 - Bushing (12 x 14 x 11)
A94134900 Winch Spare for Radial Size 50 - Skirt Assembly
S413020004 Winch Spare for Radial Size 35 to 50 - Gear Z12
S416050004 Winch Spare for Radial Size 50 - Pin
S278170002 Winch Spare for Radial Size 46 to 70 - Washer (12.5 x 48 x 1.5)
S412800041 Winch Spare for Radial Size 50 - Gear Z30
S414260004 Winch Spare for Radial Size 46 to 50 - Pawls Carrier (8 x N2)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S415590041 Winch Spare for Radial Size 50 - Gear Z20
S415610004 Winch Spare for Radial Size 50 - Pinion Z11
A72821800 Winch Spare for Radial Size 60 to 80 - Roller Bearing (14x20x18)
S281340080 Winch Spare for Radial Size 50 - Spacer roller bearings
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S413070004 Winch Spare for Radial Size 35 to 50 - Pin
A94156000 Winch Spare for Radial Size 50 - Assy Gear Z11
A94134800 Winch Spare for Radial & Performa Size 50 - Housing Assembly
M0606303 Winch Spare for Radial Size 46 to 70 - Screw (M8x25 UNI 5931)
A74135100 Winch Spare for Radial & Performa Size 50 to 90 - Needle Roller Bearing (85 x 97 x 26)
A94142200 Winch Spare for Radial & Performa Size 50 - Central Shaft Assembly
S413880002 Winch Spare for Radial Size 35 to 50 - Center Shaft Washer
S4129400A0 Winch Spare for Radial, Performa & Unipower Size 15 to 900 - Stripper arm support
S413400053 Winch Spare for Radial Size 50 - Aluminium Drum
S281690097 Winch Spare for Radial Size 40 to 50 - Ring Red Line (B28169)
A94134300 Winch Spare for Radial Size 50 - Jaw Assembly
S414280080 Winch Spare for Radial Size 46 to 50 - Peeler
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
S413440019 Winch Spare for Radial Size 50 - Stripper Arm
M6007103 Winch Spare for Radial Size 20 to 50 - Screw M6x50 UNI 6107
S4134500A5 Winch Spare for Radial & Performa Size 50 - Stripper Arm Cover
A94136400 Winch Spare for Radial Size 15 to 80 - Assembly Socket
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
S413410043 Winch Spare for Radial Size 50 - Chrome Drum
A96633400 Winch Spare for Performa Size 50 - Base Assembly
A96753100 Winch Spare for Electric Size 50 - Shaft Assembly
A94149300 Winch Spare for Electric Size 35 to 80 - Socket Assembly
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
S415070002 Winch Spare for Electric Size 50 - Disconnect Rod (221 mm)
M6015697 Winch Spare for Radial Size 60 to 70 - O Ring (5 x 5 x 1 Orm 0055)
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
— Self Tailing Winch Radial Size 50 - Aluminum Black / Two Speed
— Self Tailing Winch Radial Size 50 - Chrome / Two Speed
— Self Tailing Winch Radial Size 50 - Bronze All / Two Speed
— Self Tailing Winch Radial Size 50 - Chrome All / Two Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual