INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, dimensions, deck mounting with socket-head or hex-head bolts, service torques and the parts list for every Radial 60.2 ST version (STA, STC, STCW, STBBB, STCCC).

DocumentHarken Radial 60.2 ST Winch Installation & Maintenance Manual
FormatPDF · 23 pages · 4.2 MB
LanguageEnglish
Radial 60.2 ST Winch

Specifications

Power ratio Gear ratio
1st speed 20.30 : 1 4.80 : 1
2nd speed 61.00 : 1 14.40 : 1

The theoretical power ratio does not take friction into account.

Version Weight
STA 10.2 kg
STC / STCW 13.9 kg
STBBB / STCCC 15.4 kg

A = anodized aluminium drum; C = chrome bronze drum; CW = chrome/white; BBB = all bronze; CCC = all-chrome bronze.

Dimension mm
Height 246
Drum Ø 120.5
Line entry height 116
Base Ø 236

Maximum working load (MWL) of the Radial 60.2 ST: 1800 kg (3968 lb). Loads above the MWL can make the winch fail or pull off the deck suddenly.

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Six Ø8.5 mm holes on a Ø204 mm bolt circle; six M8 bolts (not supplied by Harken).
  • A4 stainless bolts only (DIN 267 part 11). No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Fill the holes with marine sealant and keep the base drain channels clear.

Getting to the Base

  • Socket-head bolts: unscrew the central screw, 2 Nm (18 in-lb); slide off socket and cover; remove the three screws, 4 Nm (35 in-lb); rotate and lift off the self-tailing arm; lift off the drum.
  • Hex-head M8 bolts: after the steps above, remove the three screws and the stripper arm housing, slide out the central shaft, unscrew the six housing hex screws, 20 Nm (177 in-lb), and lift off the drum support (a washer may stay inside it).
  • Position the self-tailing arm so the tail leads into the cockpit.
  • A drilling cut-out template is available on harken.com.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months; replace worn parts with original parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, pins and teeth lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls: excess grease on the pawls compromises safety.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Housing hex screws (6) 20 Nm (177 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)

Check the balls inside the drum are all in their race; push any loose ball back in. The icon on the stripper arm housing marks the stripper arm's final position: change the housing angle to move it. Refit the peeler with TOP facing up.

Radial 60.2 ST Spare Parts

From the STA parts list in the manual. Parts marked * come in the Harken service kit. Multi-part assemblies are listed by assembly code; sub-part codes are in the PDF.

Harken code Pos. Description
A94143000 1 Base assembly Winch 60 View part →
S414400004 2 Gear Z14 W60 Ask us to source it →
S413030004 3 Pawl carrier Ø8 × N2 View part →
S000080003 4 Pawl Ø8 * View part →
S000380001 5 Pawl spring Ø8 * View part →
S414390041 6 Ratchet gear Z21 × N2 View part →
S413120002 7 Washer Ø22.5 × Ø45 × 1 View part →
S278170002 8 Washer Ø12.5 × Ø48 × 1.5 View part →
S281010004 9 Pin for gear View part →
S414420041 10 Ratchet gear Z26 × N4 View part →
S414410004 11 Pawl carrier gear Z13 N4 View part →
A72821800 12 Roller bearing Ø14 × Ø20 × 18 View part →
S416030004 13 Gear pin Ø12 × Ø18 × 52.5 View part →
S414480004 14 Idler and pinion Z23/Z13 W60 Ask us to source it →
A74162300 15 Roller bearing Ø24 × Ø18 × 18 View part →
A94143100 16 Housing assembly Winch 60.2 View part →
M0606303 17 Screw M8 × 25 UNI 5931 View part →
A74145000 18 Roller bearing Ø95 × Ø107 × 26 View part →
A94143800 19 Shaft assembly Winch 60 View part →
S4144300A0 21 Stripper arm support W60/70 View part →
S281700097 22 Red line View part →
A94143500 23 Jaws assembly Winch 60 View part →
A96965900 24 Drum spare kit Winch 60 View part →
M0610280 24 Ball 5/16" (in drum kit) Ask us to source it →
M0601803 25 Screw UNI EN ISO 1207 M6 × 35 A4 View part →
S414460019 26 Stripper arm Winch 60 View part →
M0601903 27 Screw M6 × 16 UNI 1207 View part →
S4162200B1 28 Cover 2-speed W60 View part →
A94136400 29 Socket assembly W20–80 View part →

Codes that change by version

Other versions use different codes for the parts below; everything else matches the STA list. Check the PDF for your version.

Harken code Version Description
A94143400 STC / STCW / STCCC Drum spare kit Winch 60 (drum assembly Winch 60 C) Ask us to source it →
A96726000W STCW Base assembly W60 STC W Ask us to source it →
A94143500W STCW Jaws assembly Winch 60 (white) Ask us to source it →
S4162200B1W STCW Cover 2-speed W60 RAL9003 Ask us to source it →
A96908700 STBBB Base assembly Winch 60 BBB Ask us to source it →
A96924100 STBBB Jaws assembly Winch 60 BBB Ask us to source it →
A96923900 STBBB Drum spare kit Winch 60 BBB Ask us to source it →
S7123300F0 STBBB Stripper arm Winch 60 BBB Ask us to source it →
A76907400 STBBB Cover W60 BBB Ask us to source it →
A96909100 STCCC Base assembly Winch 60 CCC Ask us to source it →
A96812200 STCCC Jaws assembly Winch 60 CCC Ask us to source it →
A76811500 STCCC Cover W60 CCC Ask us to source it →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF (pawls and pawl springs) are supplied in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A94143000 Winch Spare for Radial Size 900 - Base Assembly
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S415580085 Winch Spare for Radial Size 60 - Bushing (12 x 35 x 9)
S413030004 Winch Spare for Radial Size 35 to 70 - Pawls Carrier (8xn2)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S414390041 Winch Spare for Radial Size 60 to 70 - Ratchet Gear Z21xN2
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S278170002 Winch Spare for Radial Size 46 to 70 - Washer (12.5 x 48 x 1.5)
S281010004 Winch Spare for Radial Size 70 - Pin
S414420041 Winch Spare for Radial Size 60 to 70 - Ratchet Gear Z26xN4
S414410004 Winch Spare for Radial Size 60 to 70 - Pawls Carrier Gear Z13xN4
A72821800 Winch Spare for Radial Size 60 to 80 - Roller Bearing (14x20x18)
S416030004 Winch Spare for Radial Size 70 - Gear Pin (12x18x52.5)
A74162300 Winch Spare for Radial Size 50 to 70 - Roller Bearing 24x18x8
A94143100 Winch Spare for Radial & Performa Size 60 - Housing Assembly
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
M0606303 Winch Spare for Radial Size 46 to 70 - Screw (M8x25 UNI 5931)
A74145000 Winch Spare for Radial & Performa Size 60 - Needle Roller Bearing (95 x 107 x 26)
A94143800 Winch Spare for Radial & Performa Size 60 - Shaft Assembly
S413880002 Winch Spare for Radial Size 35 to 50 - Center Shaft Washer
S4144300A0 Winch Spare for Radial & Performa Size 60 to 70 - Stripper Arm Housing
S281700097 Winch Spare for Radial Size 60 to 70 - Ring-Red Line (B28170)
A94143500 Winch Spare for Radial Size 60 - Jaw Assembly
S414850080 Winch Spare for Radial Size 60 to 70 - Peeler
A96965900 Winch Spare for Radial Size 60 - Aluminium Drum
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
S414460019 Winch Spare for Radial Size 60 to 70 - Stripper Arm
M0601903 Winch Spare for Radial & Performa Size 60 to 70 - Screw M6x16 UNI1207
S4162200B1 Winch Spare for Radial & Performa Size 60 to 70 - Stripper Arm Cover
A94136400 Winch Spare for Radial Size 15 to 80 - Assembly Socket
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
A96753600 Winch Spare for Electric Size 60 - Shaft Assembly (17-4 PH)
A94149300 Winch Spare for Electric Size 35 to 80 - Socket Assembly
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
S416130002 Winch Spare for Electric Size 60 - Disconnect Rod (255 mm)
M6015697 Winch Spare for Radial Size 60 to 70 - O Ring (5 x 5 x 1 Orm 0055)
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
— Load Controller for Radial Winch Size 60 to 70 - 12V Vertical Motor
— Self Tailing Winch Radial Size 60 - Chrome / Two Speed
— Self Tailing Winch Radial Size 60 - Aluminum Black / Two Speed
— Self Tailing Winch Radial Size 60 - Bronze All / Two Speed
— Self Tailing Winch Radial Size 60 - Chrome All / Two Speed
— Self Tailing Winch Radial Size 60 - Chrome All / Three Speed
— Self Tailing Winch Radial Size 60 - Aluminum Black / Three Speed
— Self Tailing Winch Radial Size 60 - Chrome / Three Speed
— Self Tailing Winch Radial Size 60 - Bronze All / Three Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual