INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, performance, dimensions, deck and motor installation, wire sizing, service torques and the parts list for the Radial 60 Rewind electric winch.

DocumentHarken Radial 60 Rewind Winch Installation & Maintenance Manual
FormatPDF · 26 pages · 4.6 MB
LanguageEnglish
Radial 60 Rewind Winch

Specifications

Power ratio Gear ratio
1st speed 20.30 : 1 4.80 : 1
2nd speed 61.00 : 1 14.41 : 1

The theoretical power ratio does not take friction into account.

Version Weight
ST A 22 kg
ST C / CW 26 kg
ST BBB / CCC 27.3 kg

A = anodized aluminium drum; C = chrome bronze drum; CW = chrome/white; BBB = all bronze; CCC = all-chrome bronze.

Dimension (outline drawing) mm
Base Ø 244
Height 277
Drum Ø 125
Line entry height 116
Depth below deck 183
Horizontal motor span (either side of winch axis) 294 / 118
E (deck to motor) 67

Maximum working load (MWL) of the 60 Rewind: 1800 kg (3968 lb). Loads above the MWL can make the winch fail or pull off the deck suddenly.

Performance Data

Motor 1st speed line speed 2nd speed line speed 1st speed max load 2nd speed max load
Horizontal 12V (1500 W) 17.7 m/min 5.9 m/min 600 kg 1800 kg
Horizontal 24V (2000 W) 17.7 m/min 5.9 m/min 600 kg 1800 kg

Line speed measured with no load.

Motor Nominal power Current at MWL
Horizontal 12V 1500 W 260 A
Horizontal 24V 2000 W 135 A

Installation

  • Flat area of deck, reinforced if needed to take at least twice the MWL.
  • Six Ø8.5 mm holes on a Ø204 mm bolt circle plus an Ø80 mm cut-out for the motor; six M8 socket-head bolts (not supplied by Harken).
  • A4 stainless bolts only (DIN 267 part 11). No countersunk bolts.
  • Sheet entry angle 8° ±2°, with the drive gear where the sheet enters the drum.
  • Fill the holes with marine sealant and keep the base drain channels clear.
  • The drilling template also marks the knob orientation (122°, Rewind winch only).
  • Check below deck for the flange and motor before drilling.

Getting to the Base

  • Before starting, set the Rewind knob to the position shown in the PDF.
  • Socket-head bolts: pull out the disconnect rod; unscrew the central screw, 2 Nm (18 in-lb); slide off socket and cover (mind the o-ring); remove the three screws, 4 Nm (35 in-lb); rotate and lift off the stripper arm; lift off the drum.
  • Hex-head M8 bolts: also unscrew the six housing hex screws, 20 Nm (177 in-lb), lift off the spacer and remove the drum support assembly.
  • Tools: medium flat screwdriver, 5, 6 and 3 mm hex keys. Position the self-tailing arm so the tail leads into the cockpit.

Motor and Electrical

Motor Installation

  • Switch off the power before installing or servicing the winch.
  • The motor can be coupled to the winch in different positions: check the space below deck first.
  • Flange: six M6 precote-coated screws, 8 Nm (71 in-lb). Check the seal is seated correctly.
  • Reduction gear and motor: two screws, 8 Nm (71 in-lb); align the flange.
  • Tools: 5 mm hex key, two 13 mm wrenches.
  • Test the powered winch before sailing.

Electrical

  • The Harken Dual Function Control Box is mandatory for every model; follow its own manual for wiring.
  • Cable terminals go between nut and lock nut; hold the nut with one spanner, tighten with a second, never turn the central spindle.
  • Terminal torque no greater than 10 Nm (88 in-lb).
  • Contact sequence: nut – cable terminal – self-locking washer – lock nut.

Wire size (total distance winch–battery)

Voltage Under 5 m (16.4 ft) 5–10 m (16.4–32.8 ft) 10–15 m (32.8–49.2 ft) 15–20 m (49.2–65.6 ft)
12V AWG 2 / 32 mm² AWG 0 / 50 mm² AWG 00 / 70 mm² AWG 000 / 95 mm²
24V AWG 5 / 16 mm² AWG 3 / 25 mm² AWG 2 / 35 mm² AWG 0 / 50 mm²

Control box (HCP)

Winch / voltage HCP model Ampere rating
60 Rewind – 12V HCP1720 135A
60 Rewind – 24V HCP1717 80A

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos, stickers, anodized, chromed or plastic surfaces.
  • Inspect visually at the start and end of every season.
  • Full overhaul, clean and lubricate at least every 12 months; replace worn parts with original parts only.

Overhaul

  • Tools: medium flat screwdriver, 5 and 6 mm hex keys, brush, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion.
  • Grease gears, pins and teeth lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls: excess grease on the pawls compromises safety.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Housing hex screws (6) 20 Nm (177 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)
Motor flange screws (6) 8 Nm (71 in-lb)
Motor terminals max 10 Nm (88 in-lb)

Switch off the power first. When sliding out the central shaft watch the two balls; check the drum balls are all in their race. Refit the disconnect rod with its groove in the lower part, and grease the socket o-ring before the central screw.

Radial 60 Rewind Spare Parts

From the STA EL parts list in the manual. Parts marked * come in the Harken service kit. Multi-part assemblies are listed by assembly code; sub-part codes are in the PDF.

Harken code Pos. Description
A96575800 1 Base assembly W60 RW Ask us to source it →
S657550004 2 Gear Z14 W60RW Ask us to source it →
S000080003 3 Pawl Ø8 * View part →
S000380001 4 Pawl spring Ø8 * View part →
S278170002 5 Washer Ø12.5 × Ø48 × 1.5 View part →
S281010004 6 Pin for gear View part →
S414420041 7 Ratchet gear Z26 × N4 View part →
S414410004 8 Pawl carrier gear Z13 N4 View part →
A72821800 9 Roller bearing Ø14 × Ø20 × 18 View part →
S416030004 10 Gear pin Ø12 × Ø18 × 52.5 View part →
S414480004 11 Idler and pinion Z23/Z13 W60 Ask us to source it →
A74162300 12 Roller bearing Ø24 × Ø18 × 18 View part →
A94143100 13 Housing assembly Winch 60.2 View part →
M0606303 14 Screw M8 × 25 UNI 5931 View part →
A74145000 15 Roller bearing Ø95 × Ø107 × 26 View part →
S4144300A0 17 Stripper arm housing W60/70 View part →
S281700097 18 Red line View part →
S6574800B1 19 Cover 2-speed W60 Rewind Ask us to source it →
A76575000 20 Drum kit Winch 60 STA Rewind Ask us to source it →
M0610280 21 Ball 5/16" Ask us to source it →
S657540002 22 Disconnect rod 60 Rewind Ask us to source it →
S657530004 23 Pawl carrier Ø8 × N2 Ask us to source it →
S657520041 24 Gear Z21 Ask us to source it →
S657510004 25 Main shaft W60 Rewind Ask us to source it →
M0614103 26 Ball 5-16" stainless Ask us to source it →
A96575600 27 Fork assembly Winch Rewind 60 Ask us to source it →
A96575700 28 Knob assembly W60 Rewind Ask us to source it →
S657590080 29 Switch support W60RW Ask us to source it →
S416530004 30 Pin for switch Ask us to source it →
M0624203 31 Screw M6 × 30 Ask us to source it →
A94165200 32 Socket assembly Rewind Ask us to source it →
S418590001 33 Spring Ø10.67 × 12.7 Ask us to source it →
S657620052 34 Spacer for stripper arm support W60 Rewind Ask us to source it →
M0623103 35 Screw M6 × 40 TC DIN84 A4 Ask us to source it →
M0601703 36 Screw M6 × 25 UNI 5931 Ask us to source it →
M6007103 37 Slotted cup head screw M6 × 50 UNI 6107 View part →
M0627602 38 Screw M5 × 25 Ask us to source it →
A96574900 39 Jaws assembly Winch 60 Ask us to source it →
A96574600 40 Stripper arm assembly Ask us to source it →

Codes that change by version

Harken code Version Description
A76645700 STC / STCW / STCCC Drum kit Winch 60 STC Rewind Ask us to source it →
A96990500 STC Jaws assembly Winch 60 STC Rewind Ask us to source it →
A96760800W STCW Base assembly W60 RW W Ask us to source it →
A96574900W STCW Jaws assembly Winch 60 STCW Rewind Ask us to source it →
A96934300 STBBB Base assembly W60 RW STBBB Ask us to source it →
A76934400 STBBB Drum kit Winch 60 STB Rewind Ask us to source it →
A96990600 STBBB Jaws assembly Winch 60 STB Rewind Ask us to source it →
A76934000 STBBB Stripper arm assembly Winch 60 RW B Ask us to source it →
A96934500 STCCC Base assembly W60 RW STCCC Ask us to source it →
A96934600 STCCC Jaws assembly Winch 60 STCCC Ask us to source it →

Motor and drive kits

Part no. Description
A93127900 Gear reduction kit VF49 Ask us to source it →
A94194900 LM gear reduction kit 1/24 View part →
A94149200 Electric motor flange kit View part →
A94149200L Electric motor flange kit, left Ask us to source it →
A96656800 Electric motor kit 12V Winch 60 RW (motor with 4.5 Nm brake) Ask us to source it →
A96656900 Electric motor kit 24V Winch 60 RW (motor with 4.5 Nm brake) Ask us to source it →
A94966500 Horizontal motor flange kit (H82) View part →
A96589000 Performa horizontal motor clutch kit View part →

Ordering Spare Parts

Quote the Harken part number from the parts list and the winch serial number, printed on the plate on the drum support. Parts marked * in the PDF (pawls and pawl springs) are supplied in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
HCP1720 Winch Circuit Breaker - 135 Amp 12V/24V
HCP1717 Winch Circuit Breaker - 80 Amp 12V/24V
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
S415580085 Winch Spare for Radial Size 60 - Bushing (12 x 35 x 9)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S278170002 Winch Spare for Radial Size 46 to 70 - Washer (12.5 x 48 x 1.5)
S281010004 Winch Spare for Radial Size 70 - Pin
S414420041 Winch Spare for Radial Size 60 to 70 - Ratchet Gear Z26xN4
S414410004 Winch Spare for Radial Size 60 to 70 - Pawls Carrier Gear Z13xN4
A72821800 Winch Spare for Radial Size 60 to 80 - Roller Bearing (14x20x18)
S416030004 Winch Spare for Radial Size 70 - Gear Pin (12x18x52.5)
A74162300 Winch Spare for Radial Size 50 to 70 - Roller Bearing 24x18x8
A94143100 Winch Spare for Radial & Performa Size 60 - Housing Assembly
M0606303 Winch Spare for Radial Size 46 to 70 - Screw (M8x25 UNI 5931)
A74145000 Winch Spare for Radial & Performa Size 60 - Needle Roller Bearing (95 x 107 x 26)
S4144300A0 Winch Spare for Radial & Performa Size 60 to 70 - Stripper Arm Housing
S281700097 Winch Spare for Radial Size 60 to 70 - Ring-Red Line (B28170)
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
M6007103 Winch Spare for Radial Size 20 to 50 - Screw M6x50 UNI 6107
A94194900 Winch Spare for Radial Size 50 to 70 - Gear BoxVF49
A94149200 Winch Spare for Electric Size 35 to 70 - Electric Motor Flange Assembly
A94966500 Winch Spare for Electric Size 50 to 70 - Support Flange Gear Box Tall
M6015697 Winch Spare for Radial Size 60 to 70 - O Ring (5 x 5 x 1 Orm 0055)
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
A96589000 Winch Spare for Electric Size 50 to 70 - Motor Clutch - Horizontal 17-4HP E=43 mm
— Electric Winch Rewind Size 60 - 12V / Aluminum Black / Two Speed / Left Mount
— Electric Winch Rewind Size 60 - 24V / Aluminum Black / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 12V / Aluminum Black / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 24V / Aluminum Black / Two Speed / Left Mount
— Electric Winch Rewind Size 60 - 12V / Bronze All / Two Speed / Left Mount
— Electric Winch Rewind Size 60 - 24V / Bronze All / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 12V / Bronze All / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 24V / Bronze All / Two Speed / Left Mount
— Electric Winch Rewind Size 60 - 24V / Chrome / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 12V / Chrome / Two Speed / Left Mount
— Electric Winch Rewind Size 60 - 24V / Chrome / Two Speed / Left Mount
— Electric Winch Rewind Size 60 - 12V / Chrome / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 12V / Chrome All / Two Speed / Left Mount
— Electric Winch Rewind Size 60 - 12V / Chrome All / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 24V / Chrome All / Two Speed / Right Mount
— Electric Winch Rewind Size 60 - 24V / Chrome All / Two Speed / Left Mount

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual