INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, weights, outline dimensions, deck mounting, the strip-down and service procedure, and the parts list for every Radial 70.2 ST version (STA, STC, STCW, STBBB, STCCC).

DocumentHarken Radial 70.2 ST Winch Installation & Maintenance Manual
FormatPDF · 23 pages · 4.1 MB
LanguageEnglish
Radial 70.2 ST Winch

Specifications

Power ratio Gear ratio
1st speed 22.20 : 1 5.70 : 1
2nd speed 72.00 : 1 18.50 : 1

The theoretical power ratio does not take friction into account.

Version Drum Weight
STA Anodized aluminium 11.3 kg
STC / STCW Chrome bronze / chrome-white 15.1 kg
STBBB / STCCC All bronze / all-chrome bronze 16.7 kg
Dimension mm
Base Ø 240
Top Ø 131
Height 257
Line entry height 115

Maximum working load (MWL): 2700 kg (5952 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Mount on a flat area of deck, reinforced if needed to take at least twice the MWL.
  • Sheet entry angle 8° ±2°; mount so the drive gear sits where the sheet enters the drum.
  • Six M8 bolts through 8.5 mm holes on a Ø205 mm bolt circle (drilling template on harken.com).
  • A4 stainless bolts only (DIN 267 part 11). Do not use countersunk bolts. Bolts are not supplied.
  • Fill the holes with marine sealant and clear excess from the holes and base drainage channels.

Two Ways In

  • Socket-head bolts: remove the central screw, socket and cover, the three self-tailing arm screws, the arm and the drum.
  • Hex-head M8 bolts: also remove the stripper arm housing, slide out the central shaft, undo the six hex screws and lift off the drum support. The washer may stay inside the drum support.
  • Position the self-tailing arm so the tail leads into the cockpit.
  • Reassemble in reverse order, applying the maintenance products.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos and stickers; no polishes or abrasives on anodized, chromed or plastic surfaces.
  • Keep the base holes and drainage channels clear so water cannot collect.
  • Inspect visually at the start and end of every season; full overhaul, clean and lubricate at least every 12 months.

Overhaul

  • Tools: medium flat screwdriver, 5 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion; replace with original parts only.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls: excess grease near the pawls compromises winch safety.
  • Check the drum balls sit correctly in their race; push any loose ball back in.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Self-tailing arm screws (3) 4 Nm (35 in-lb)
Drum support hex screws (6) 20 Nm (177 in-lb)
Jaw screws (4) 4 Nm (35 in-lb)

When refitting the jaws, the peeler goes between them with the letters TOP facing up, aligned with the stripper arm. Hold each pawl spring closed, slide the pawl in, and check it opens and closes easily with a finger.

Radial 70.2 ST Spare Parts

From the Radial 70.2 STA parts list. Other versions share the drivetrain but use different codes for these parts:

Version Base assy Drum kit Jaws assy Stripper arm Cover
STA A94146700 A96966000 A94147100 S414730019 S4160400B1
STC A94146700 A94148800 A94147100 S414730019 S4160400B1
STCW A96726200W A94148800 A94147100W S414730019 S4160400B1W
STBBB A96980000 A96924300 A96924400 S7180100F0 A76924200
STCCC A96980100 A94148800 A96812300 S414730019 A76811600
Harken code Pos. Description
A94146700 1 Base assembly W70 View part →
S476030004 1 Centering bushing Ø12 Ask us to source it →
S4152300A7 1 Bushing Ø22 × Ø25 × 9.5 View part →
S415580085 1 Bushing Ø12 × Ø35 × 9 View part →
S414770004 2 Gear Z13 W70 View part →
S413030004 3 Pawl carrier Ø8 × N2 View part →
S000080003 4 Pawl Ø8 * View part →
S000380001 5 Pawl spring Ø8 * View part →
S414390041 6 Ratchet gear Z21 × N2 View part →
S413120002 7 Washer Ø22.5 × Ø45 × 1 View part →
S278170002 8 Washer Ø12.5 × Ø48 × 1.5 View part →
S281010004 9 Pin for gear View part →
S414420041 10 Ratchet gear Z26 × N4 View part →
S414410004 11 Pawl carrier gear Z13 N4 View part →
A72821800 12 Roller bearing 14/20/18 View part →
S416030004 13 Gear pin Ø12 × Ø18 × 52.5 View part →
S414760004 14 Idler and pinion Z26/Z13 W70 View part →
A74162300 15 Roller bearing 24 × 18 × 18 View part →
A94146800 16 Housing assembly W70 (drum support) View part →
M0606303 17 Screw M8 × 25 UNI 5931 View part →
A74147500 18 Roller bearing Ø102 × Ø114 × 26 View part →
A94147900 19 Shaft assembly W70 View part →
S413880002 19 Washer Ø17.2 × Ø32 × 1.5 View part →
S4144300A0 21 Stripper arm support W60/70 View part →
S281700097 22 Red line View part →
A94147100 23 Jaws assembly W70 (jaws, peeler, springs) View part →
A96966000 24 Drum spare kit W70 (STA) View part →
M0610280 24 Ball 5/16" (50 per drum) Ask us to source it →
M0601803 25 Screw UNI EN ISO 1207 M6 × 35 A4 View part →
S414730019 26 Stripper arm W70 View part →
M0601903 27 Screw M6 × 16 UNI 1207 View part →
S4160400B1 28 Cover 2-speed W70 View part →
A94136400 29 Socket assembly W20–80 View part →
S415130085 29 Socket handle W20/80 View part →
M0614303 29 Screw M8 × 20 UNI 6109 View part →

Quote the Harken part number and the winch serial number, printed on the plate on the drum support. Parts marked * are available in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Harken part no. Our part
A94146700 Winch Spare for Radial Size 60 - Base Assembly
S4152300A7 Winch Spare for Radial Size 35 to 40 - Bushing Igus (22 x 25 x 9.5 mm)
S415580085 Winch Spare for Radial Size 60 - Bushing (12 x 35 x 9)
S414770004 Winch Spare for Radial Size 70 - Gear Z13
S413030004 Winch Spare for Radial Size 35 to 70 - Pawls Carrier (8xn2)
S000080003 Winch Spare for Radial Size 15 to 70 - Pawl 8 Dia 316SS (B008)
S000380001 Winch Spare for Radial & Performa Size 15 to 80 - Pawl Spring (B038)
S414390041 Winch Spare for Radial Size 60 to 70 - Ratchet Gear Z21xN2
S413120002 Winch Spare for Radial Size 35 to 70 - Washer (22.5 x 45 x 1)
S278170002 Winch Spare for Radial Size 46 to 70 - Washer (12.5 x 48 x 1.5)
S281010004 Winch Spare for Radial Size 70 - Pin
S414420041 Winch Spare for Radial Size 60 to 70 - Ratchet Gear Z26xN4
S414410004 Winch Spare for Radial Size 60 to 70 - Pawls Carrier Gear Z13xN4
A72821800 Winch Spare for Radial Size 60 to 80 - Roller Bearing (14x20x18)
S416030004 Winch Spare for Radial Size 70 - Gear Pin (12x18x52.5)
S414760004 Winch Spare for Radial Size 70 - Idler and Pinion Z26/Z13
A74162300 Winch Spare for Radial Size 50 to 70 - Roller Bearing 24x18x8
A94146800 Winch Spare for Radial & Performa Size 70 - Housing Assembly
S4130900A7 Winch Spare for Radial Size 35 - Bushing (D22 x D25 x 8)
M0606303 Winch Spare for Radial Size 46 to 70 - Screw (M8x25 UNI 5931)
A74147500 Winch Spare for Radial & Performa Size 70 - Needle Roller Bearing (102 x 114 x 26)
A94147900 Winch Spare for Radial & Performa Size 70 - Shaft Assembly
S413880002 Winch Spare for Radial Size 35 to 50 - Center Shaft Washer
S4144300A0 Winch Spare for Radial & Performa Size 60 to 70 - Stripper Arm Housing
S281700097 Winch Spare for Radial Size 60 to 70 - Ring-Red Line (B28170)
A94147100 Winch Spare for Radial Size 70 - Jaw Assembly
S414850080 Winch Spare for Radial Size 60 to 70 - Peeler
A96966000 Winch Spare for Radial Size 70 - Aluminium Drum
M0601803 Winch Spare for Radial Size 35 to 70 - Screw UNI EN ISO 1207:1996 M6x35 A4
S414730019 Winch Spare for Radial Size 70 - Stripper Arm
M0601903 Winch Spare for Radial & Performa Size 60 to 70 - Screw M6x16 UNI1207
S4160400B1 Winch Spare for Radial & Performa Size 70 - Cover
A94136400 Winch Spare for Radial Size 15 to 80 - Assembly Socket
S415130085 Winch Spare for Radial Size 20 to 35 - Washer Socket
M0614303 Winch Spare for Radial & Performa Size 15 to 80 - Screw (M8x20 UNI 6109)
A94148800 Winch Spare for Radial Size 70 - Chrome Drum
A96753500 Winch Spare for Electric Size 70 - Shaft Assembly (17-4 PH)
A94149300 Winch Spare for Electric Size 35 to 80 - Socket Assembly
S414940085 Winch Spare for Radial Size 40 to 46 - Socket Washer
S414930003 Winch Spare for Radial Size 40 to 46 - Nut Screw Drilled
M0679797 Winch Spare for Radial Size 35 to 46 - O-Ring w/Plastic Insert
M6015697 Winch Spare for Radial Size 60 to 70 - O Ring (5 x 5 x 1 Orm 0055)
M6007297 Winch Spare for Radial Size 35 to 70 - Lip Seal (17 x 30 x 7)
— Self Tailing Winch Radial Size 70 - Bronze All / Two Speed
— Self Tailing Winch Radial Size 70 - Chrome / Two Speed
— Self Tailing Winch Radial Size 70 - Aluminum Black / Two Speed
— Self Tailing Winch Radial Size 70 - Chrome All / Two Speed
— Self Tailing Winch Radial Size 70 - Chrome / Three Speed
— Self Tailing Winch Radial Size 70 - Aluminum Black / Three Speed
— Self Tailing Winch Radial Size 70 - Bronze All / Three Speed
— Self Tailing Winch Radial Size 70 - Chrome All / Three Speed

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual