INSTALLATION & MAINTENANCE MANUAL

Ratios, working load, weights, outline dimensions, deck mounting, the full strip-down and service procedure, and the parts list for the Radial 80.2 ST (STA, STC).

DocumentHarken Radial 80.2 ST Winch Installation & Maintenance Manual
FormatPDF · 18 pages · 2.8 MB
LanguageEnglish
Radial 80.2 ST Winch

Specifications

Power ratio Gear ratio
1st speed 28.85 : 1 9.94 : 1
2nd speed 93.24 : 1 32.12 : 1

The theoretical power ratio does not take friction into account.

Version Drum Weight
STA Anodized aluminium 21.2 kg
STC Chrome bronze 28.8 kg
Dimension mm
Base Ø 287
Top Ø 177
Height 320
Line entry height 164

Maximum working load (MWL): 4500 kg (9920 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Mount on a flat area of deck, reinforced if needed to take at least twice the MWL.
  • Sheet entry angle 8° ±2°; mount so the drive gear sits where the sheet enters the drum.
  • Eight M10 socket-head bolts through 10.2 mm holes on a Ø233 mm bolt circle (drilling template on harken.com).
  • A4 stainless bolts only (DIN 267 part 11). Do not use countersunk bolts. Bolts are not supplied.
  • Fill the holes with marine sealant and clear excess from the holes and base drainage channels.

Strip for Mounting

  • Mounting requires the full disassembly procedure.
  • Central screw, socket and cover off; three screws and the stripper arm; lift the drum.
  • Undo the six screws and lift off the housing; then washer, inner spacer, roller bearing, pinion assembly and spacer.
  • The plastic washer must sit in contact with the winch base on reassembly.
  • Position the self-tailing arm so the tail leads into the cockpit.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos and stickers; no polishes or abrasives on anodized, chromed or plastic surfaces.
  • Keep the base holes and drainage channels clear so water cannot collect.
  • Inspect visually at the start and end of every season; full overhaul, clean and lubricate at least every 12 months.

Overhaul

  • Tools: medium flat screwdriver, 6 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion; replace with original parts only.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls: excess grease near the pawls compromises winch safety.
  • Check the drum balls sit correctly in their race; push any loose ball back in.
Fastener Torque
Central screw 2 Nm (18 in-lb)
Stripper arm screws (3) 4 Nm (35 in-lb)
Housing screws (6) 20 Nm (177 in-lb)
Jaw screws (3) 4 Nm (35 in-lb)

When refitting the jaws, the peeler goes between them with the letters TOP facing up, aligned with the stripper arm. Hold each pawl spring closed, slide the pawl in, and check it opens and closes easily with a finger.

Radial 80.2 ST Spare Parts

From the Radial 80.2 STA / STC parts lists; the two versions differ only in the drum assembly.

Harken code Pos. Description
A94158200 1 Base assembly W80 Ask us to source it →
S285040001 2 Pawl spring * View part →
S392440004 3 Pawl Ø10 * View part →
HFS753 4 Plug pawl retainer Ask us to source it →
S434110081 5 Washer Ø48 × Ø26 × 1.5 View part →
A74506900 6 Bearing Ø25 × Ø35 × 15 Ask us to source it →
S405830004 7 Shaft, final drive pinion Ask us to source it →
S438860081 8 Washer Ø54 × Ø35.2 × 3 Ask us to source it →
S405540004 9 Final drive pinion Ask us to source it →
S405550004 10 Gear Z36 Ask us to source it →
S434170081 11 Washer Ø69 × Ø45 × 1.5 View part →
S402260041 12 Bushing, 4th gear pinion Ask us to source it →
S405580004 13 Pinion 3rd speed Ask us to source it →
S423870004 14 Gear Z=36 Ask us to source it →
A74159000 15 Drum assembly W80 (STA) Ask us to source it →
A74159100 15 Drum assembly W80 C (STC) Ask us to source it →
A94159200 16 Jaws assembly W80 (jaws, peeler, springs, balls) Ask us to source it →
M0624703 17 Screw M8 × 50 UNI 5931 Ask us to source it →
A94158700 18 Housing assembly W80 Ask us to source it →
A74059500 19 Roller bearing, lower Ask us to source it →
A74158900 20 Roller bearing Ø148 × 160 × 30 Ask us to source it →
S415960053 21 Stripper arm support Ask us to source it →
S4144300A0 22 Stripper arm housing W60/70 View part →
A73129200 23 Roller bearing 50-62-20 Ask us to source it →
S413880002 24 Washer Ø17.2 × Ø32 × 1.5 View part →
M0624603 25 Screw M8 × 40 UNI 5931 Ask us to source it →
M0635103 26 Socket head screw M6 × 16 UNI 5931 View part →
S386550097 27 Red line Ask us to source it →
S416400004 28 Shaft Z13 W80 Ask us to source it →
S434160081 29 Washer Ø59 × Ø26 × 1.5 View part →
S402050004 30 Washer Ø25.2 × Ø61 × 2.4 Ask us to source it →
S405860080 31 Spacer Ask us to source it →
A94055700 32 Pinion Z14 assembly Ask us to source it →
S455420081 32 Bushing Ø24.5 × Ø28.5 × 27 Ask us to source it →
S405620004 33 Hub, 2nd ratchet Ask us to source it →
S415860080 34 Inner spacer Ask us to source it →
A94159901 36 Stripper arm kit W80 (arm and pin) Ask us to source it →
M0601903 37 Screw M6 × 16 UNI 1207 View part →
A94136400 38 Socket assembly W20–80 View part →
S4160000B7 39 Cover W80.2 ST Ask us to source it →

Quote the Harken part number and the winch serial number, printed on the plate on the drum support. Parts marked * are available in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual