INSTALLATION & MAINTENANCE MANUAL

Three-speed ratios, working load, weights, outline dimensions, deck mounting, the strip-down and service procedure, and the parts list for the Radial 80.3 ST (STA, STC).

DocumentHarken Radial 80.3 ST Winch Installation & Maintenance Manual
FormatPDF · 19 pages · 3.5 MB
LanguageEnglish
Radial 80.3 ST Winch

Specifications

Power ratio Gear ratio
1st speed 8.01 : 1 2.76 : 1
2nd speed 28.85 : 1 9.94 : 1
3rd speed 93.24 : 1 32.12 : 1

The theoretical power ratio does not take friction into account.

Version Drum Weight
STA Anodized aluminium 22.7 kg
STC Chrome bronze 30.7 kg
Dimension mm
Base Ø 287
Drum Ø 177
Height 326
Line entry height 164

Maximum working load (MWL): 4500 kg (9921 lb). Loads above the MWL can make the winch fail or pull off the deck.

Installation

  • Mount on a flat area of deck, reinforced if needed to take at least twice the MWL.
  • Sheet entry angle 8° ±2°; mount so the drive gear sits where the sheet enters the drum.
  • M10 socket-head or hex-head bolts on a Ø233 mm bolt circle. The text calls for six 10 mm holes; the drilling diagram shows eight Ø10 holes: use the Harken template.
  • A4 stainless bolts only (DIN 267 part 11). Do not use countersunk bolts. Bolts are not supplied.
  • Fill the holes with marine sealant and clear excess from the holes and base drainage channels.

Strip for Mounting

  • Mounting requires removing the drum support.
  • Socket assembly, cover plate, three screws and the self-tailing arm; three screws and the drum.
  • Six screws and the assembly flange; slide out the command tube and roller bearings.
  • Six screws and the drum support; the winch base is now free for bolting.
  • Position the self-tailing arm so the tail leads into the cockpit.

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos and stickers; no polishes or abrasives on anodized, chromed or plastic surfaces.
  • Keep the base holes and drainage channels clear so water cannot collect.
  • Inspect visually at the start and end of every season; full overhaul, clean and lubricate at least every 12 months.

Overhaul

  • Tools: medium flat screwdriver, 6 mm hex key, rags.
  • Clean metal parts with a residue-free degreaser; rinse plastic parts in fresh water and dry with lint-free cloths.
  • Check gear and ring-gear teeth, roller bearings and cages, pins and pawls for wear or corrosion; replace with original parts only.
  • Grease gears, gear pins, teeth and moving parts lightly with Harken grease, applied with a brush.
  • Oil the pawls and springs only. Never grease the pawls: excess grease near the pawls compromises winch safety.
  • Clutch pin: fit the spring with the pin pointing up, wound anticlockwise from the pin.
  • The plastic washer must sit in contact with the winch base.

The manual gives one torque value: jaw screws (3) 4 Nm (35 in-lb). Contact Harken Tech Service for the others.

When refitting the jaws, the peeler goes between them with the letters TOP facing up, aligned with the stripper arm. Hold each pawl spring closed, slide the pawl in, and check it opens and closes easily with a finger.

Radial 80.3 ST Spare Parts

From the Radial 80.3 STA / STC parts lists; the two versions differ only in the drum assembly.

Harken code Pos. Description
A94158200 1 Base assembly W80 Ask us to source it →
A74506900 2 Bearing Ø25 × Ø35 × 15 Ask us to source it →
S434170081 3 Washer Ø69 × Ø45 × 1.5 View part →
S423870004 4 Gear Z=36 Ask us to source it →
S402260041 5 Bushing, 4th gear pinion Ask us to source it →
S392440004 6 Pawl Ø10 * View part →
S285040001 7 Pawl spring * View part →
HFS753 8 Plug pawl retainer Ask us to source it →
S405580004 9 Pinion 3rd speed Ask us to source it →
S434110081 10 Washer Ø48 × Ø26 × 1.5 View part →
S405830004 11 Shaft, final drive pinion Ask us to source it →
S405550004 12 Gear Z36 Ask us to source it →
S405540004 13 Final drive pinion Ask us to source it →
S438860081 14 Washer Ø54 × Ø35.2 × 3 Ask us to source it →
A94158700 15 Housing assembly W80 Ask us to source it →
A74059500 17 Roller bearing Ask us to source it →
A74158900 18 Roller bearing Ø148 × 160 × 30 Ask us to source it →
S415960053 19 Stripper arm support Ask us to source it →
A73129200 20 Roller bearing 50-62-20 Ask us to source it →
S413880002 21 Washer Ø17.2 × Ø32 × 1.5 View part →
M0624603 22 Screw M8 × 40 UNI 5931 Ask us to source it →
M0635103 23 Socket head screw M6 × 16 UNI 5931 View part →
S386550097 24 Red line Ask us to source it →
S416400004 25 Shaft Z13 W80 Ask us to source it →
S434160081 26 Washer Ø59 × Ø26 × 1.5 View part →
S402050004 27 Washer Ø25.2 × Ø61 × 2.4 Ask us to source it →
S405860080 28 Spacer Ask us to source it →
A94055700 29 Pinion Z14 assembly Ask us to source it →
S405620004 30 Hub, 2nd ratchet Ask us to source it →
A94159500 31 3rd speed clutch assembly W80 (command tube, dog clutch, ball plungers) Ask us to source it →
S4155700A0 32 Stripper arm support Ask us to source it →
S415400004 33 Pawl carrier 3-speed Ask us to source it →
S495120080 34 Washer Ø50.2 × Ø69 × 1.5 Ask us to source it →
S000080003 35 Pawl Ø8 * View part →
S000380001 36 Pawl spring Ø8 * View part →
S417990041 37 Ratchet gear Z21 × N4 Ask us to source it →
S418000080 38 Flange 1st speed W80 Ask us to source it →
S377510001 39 Clutch spring Ask us to source it →
A73422600 40 Bearing 45 × 55 × 12 Ask us to source it →
M0601903 41 Screw M6 × 16 UNI 1207 View part →
A74159000 42 Drum assembly W80 (STA) Ask us to source it →
A74159100 42 Drum assembly W80 C (STC) Ask us to source it →
A94159200 43 Jaws assembly W80 Ask us to source it →
M0624703 44 Screw M8 × 50 UNI 5931 Ask us to source it →
A94159901 45 Stripper arm kit W80 Ask us to source it →
S4180100B7 46 Cover W80.3 ST Ask us to source it →
A94154700 47 Socket assembly 3-speed Ask us to source it →
A96726500 48 W80-1000 3-speed kit (3-speed pin, idler gear Z12, bushing, washer, fasteners) Ask us to source it →

Quote the Harken part number and the winch serial number, printed on the plate on the drum support. Parts marked * are available in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual