INSTALLATION MANUAL

Sizing, Reflex cable, fork-attach and cable-less part numbers, sailmaker's dimensions, torsion cable length and clamp torques, furling line, operation and maintenance for the Reflex Unit 1, 2 and 3 furlers.

DocumentHarken Reflex Furling Unit 1, 2, 3 Installation Manual
FormatPDF · 32 pages · 5.5 MB
LanguageEnglish
Reflex Furling Unit 1, 2, 3

Sizing Check

Unit Part no. Application Typical boat length Max. sail area
1 7351.10 Asymmetric spinnaker 7.5–11 m (25–36 ft) 112 m² (1200 ft²)
1 7361.10 Code zero 6.7–10 m (22–32 ft) 60 m² (650 ft²)
2 7352.10 Asymmetric spinnaker 10–14 m (34–45 ft) 168 m² (1800 ft²)
2 7362.10 Code zero 9–12 m (30–40 ft) 84 m² (900 ft²)
3 7353.10 Asymmetric spinnaker, monohull 13–17.7 m (44–58 ft) 223 m² (2400 ft²)
3 7353.10 Asymmetric spinnaker, multihull 12–16.7 m (39–55 ft) 223 m² (2400 ft²)
3 7363.10 Code zero, monohull 12–16.5 m (39–54 ft) 158 m² (1700 ft²)
3 7363.10 Code zero, multihull 11–15 m (36–50 ft) 140 m² (1500 ft²)

Code zero loads are higher, so maximum boat and sail size are smaller; on multihulls downsize the maximums by 10%. Fork-attach and cable-less components share the same sizing per unit.

Reflex kit (mm) 7351.10 7361.10 7352.10 7362.10 7353.10 7363.10
A snap shackle / D-shackle 55 / 28 55 / 28 61 / 38 61 / 38 88 / 48 88 / 48
B diameter 140 140 167 167 215 215
C line height 54 54 64 64 89 89
D tack swivel 94 — 111 — 157 —
E hole top 114 103 134 121 199 181
F thimble top 131 120 152 138 131 196
H hole bottom (head) 53 53 76 76 109 109
I thimble bottom (head) 83 83 93 93 124 124
J clamp height 50 50 60 60 166 166

Luff length: asymmetric spinnakers use offset H at the top and D at the bottom; code zeros use H at the top and E at the bottom.

Components by Unit

Component Unit 1 Unit 2 Unit 3
Asymmetric system with cable 7351.10.16M / .18M / .20M 7352.10.20M / .23M / .25M 7353.10.22M / .26M
Code zero system (no cable) 7361.10 7362.10 7363.10
Head swivel with soft cover 7351.28 (CV803) 7352.28 (CV804) 7353.28 (CV805)
Tack swivel terminal 7351.26 7352.26 7353.26
Fixed tack terminal (code zero) 7351.27 7352.27 7353.27
Drive unit 7351.10BASE 7352.10BASE 7353.10BASE
Reflex torsion cable, by the foot 7371 7372 7373
Torsion cable clamp set 7357 7358 7367
Snap shackle threaded adapter 7351.20 7352.20 7353.20
D-shackle threaded adapter 7351.21 7352.21 7353.21
D-shackle only, HR 2109 (6 mm) 2116 (8 mm) 2123 (10 mm)
2:1 / soft attachment threaded adapter 7351.22 7352.22 7353.22
Heat-shrink tubing HCP2070 HCP2070 HCP2165
Fork-head swivel with soft cover 7351.37 7352.37 7353.37
Fork-tack with swivel (asymmetric) 7351.39 7352.39 7353.39
Fork-tack (code zero) 7351.38 7352.38 7353.38
Cable-less head swivel 7351.24 7352.24 7353.24
Cable-less tack plate 7351.23 7352.23 7353.23

Cable lengths: 7351.10.16M 16.15 m (53'), .18M 18.29 m (60'), .20M 20.12 m (66'); 7352.10.20M 20.12 m (66'), .23M 22.87 m (75'), .25M 25 m (82'); 7353.10.22M 22 m (72'), .26M 26 m (85'). Fork components take the thimbles of non-Harken torsion cables. Cable-less fittings are webbed onto sails with load-carrying unidirectional luff fibres. Leads: 7356 fairlead kit, 7355 double fairlead, 7359 fairlead with cleats, 7360 aft block with bungee.

Fork-attach (mm) Unit 1 Unit 2 Unit 3
E pin centre, asymmetric / code zero 114 / 105 136 / 125 190 / 173
F fork width 14 18.3 20.3
G pin diameter 7.9 12.6 15.8
H pin to throat 22 28 35
I halyard to pin 63 74 100

Cable Terminals

  • Rough cable length is about the full-hoist (FH) length. Unit 3: add 260 mm (10") for an asymmetric, 80 mm (3") for a code zero.
  • Build the head terminal first; cut only after dry-fitting at the boat.
  • Clamp distance from thimble: Units 1 and 2 10 mm (3/8"), Unit 3 20 mm (3/4"); tail about 90 mm (3.5").
  • Close the long corner screws evenly to 8 mm (5/16"), add the short screws with blue Loctite, close to 5 mm (3/16"), then replace the long screws.
  • Clamp torque: Units 1 and 2 5.6 Nm (4.2 ft-lb); Unit 3 40.67 Nm (30 ft-lb). Unit 3: grease or anti-seize under the screw heads.
  • After the first sail in significant wind, retighten both clamps (about 40 Nm / 30 ft-lb on Unit 3) until the halves close.

Cable Stretch (A to B)

Full hoist length Unit 1 Unit 2
14–16 m (45–53') 150 mm —
16–18 m (53–59') 190 mm 250 mm
18–20 m (59–66') 230 mm 300 mm
20–23 m (66–75') 280 mm 350 mm
23–25 m (75–82') — 450 mm
Unit 3 full hoist Asymmetric Code zero
17–18 m (55–60') 40 mm (2.5") 125 mm (5")
19–20 m (61–65') 50 mm (3") 175 mm (7")
20–21 m (66–70') 60 mm (3.5") 225 mm (9")
22–23 m (71–75') 75 mm (4") 280 mm (11")
23–24 m (76–80') 85 mm (4.5") 330 mm (13")
25–26 m 110 mm (5") 380 mm (15")

Stretch is for a new cable. Unit 3: add the 165 mm (6 1/2") clamp length from point A plus 100 mm (4") of tail. Shrink the tube only after sailing.

Furling Line and First Hoist

Furling Line

  • Continuous loop: Unit 1 6 mm (1/4"), Unit 2 8 mm (5/16"), Unit 3 10 mm (3/8").
  • Loop length, cruise: furler to aft cockpit block. Race: J dimension plus bowsprit, minus 60 cm (2'). Double it and add the splice overlap.
  • Leads fit 25 mm (1") stanchions; line outboard of the stanchions.
  • Threaded adapter: back out no more than one turn to align the set screws; blue Loctite on the set screws.

Hoisting

  • Drive unit on the bow with the line guard facing aft.
  • Head to the head swivel eye with a soft shackle; asymmetric tack to the tack swivel with a longer soft shackle; code zero tack to the thimble hole.
  • Tension the halyard only enough to straighten the cable and rolled sail.
  • Units 1 and 2 with a code zero: always add a tension-handling line. The Unit 3 cable has a Dyneema core for code zero luff loads.
  • A 2:1 or 3:1 tack line pulls against the halyard: downsize it.

Over-tensioning the halyard makes furling harder and can damage components. Stand clear of the drive sheave and furling line while the sail unfurls.

Operation and Maintenance

  • Asymmetric: tack on a swivel, furling runs top to bottom. Code zero: fixed tack, furling along the luff.
  • Sail change: pull the spring pin, slide one terminal out of the T-slot and the next one in; cable-less sails fit the same T-slot.
  • Flush often with fresh water, periodically with mild detergent while spinning parts.
  • Drive unit: remove the line, flush both sides of the feeder while rotating the sheave; flush the T-slot and spring pin.
  • Check fasteners, shackles and soft attachments for chafe or failing splices. Store rinsed and dry.

Parts in this Manual We Carry

Harken part numbers as printed in the installation manual, matched to the genuine parts in our store.

Harken part no. Our part
7361.10 Furlers - Reflex Code Zero Unit 1 (Drum and Swivel) - Boat Size: 35.0 - 45.0 ft (10.6 - 13.7 m)
7362.10 Furlers - Reflex Code Zero Unit 2 (Drum and Swivel) - Boat Size: 40.0 - 50.0 ft (12.2 - 15.2 m)
7363.10 Furlers - Reflex Code Zero Unit 3 (Drum and Swivel) - Boat Size: 39.0 - 54.0 ft (11.9 - 16.5 m) - Cable Length: 72.0 ft (22.0 m)
7351.37 Head Forked Swivel for Reflex Unit 1 Furlers
7351.39 Forked Free Tack Adapter (14mm Fork Gap) for Reflex Unit 1 Furlers
7351.38 Forked Fixed Tack Adapter (14mm Fork Gap) for Reflex Unit 1 Furlers
7351.24 Head Web-On Cable-Less Swivel for Reflex Unit 1 Furlers
7351.23 Tack Web-On Cable-Less Adapter for Reflex Unit 1 Furlers
7352.37 Head Forked Swivel for Reflex Unit 2 Furlers
7352.39 Forked Free Tack Adapter (18mm Fork Gap) for Reflex Unit 2 Furlers
7352.38 Forked Fixed Tack Adapter (18mm Fork Gap) for Reflex Unit 2 Furlers
7352.24 Head Web-On Cable-Less Swivel for Reflex Unit 2 Furlers
7352.23 Tack Web-On Cable-Less Adapter for Reflex Unit 2 Furlers
7353.37 Head Forked Swivel for Reflex Unit 3 Furlers
7353.39 Forked Free Tack Adapter (20mm Fork Gap) for Reflex Unit 3 Furlers
7353.38 Forked Fixed Tack Adapter (20mm Fork Gap) for Reflex Unit 3 Furlers
7353.24 Head Web-On Cable-Less Swivel for Reflex Unit 3 Furlers
7353.23 Tack Web-On Cable-Less Adapter for Reflex Unit 3 Furlers
7351.10.16M Furlers - Reflex Asymmetric Spinnaker Unit 1 - Boat Size: 35.0 - 40.0 ft (10.6 - 12.0 m) - Cable Length: 53.0 ft (16.0 m)
7352.10.20M Furlers - Reflex Asymmetric Spinnaker Unit 2 - Boat Size: 50.0 - 60.0 ft (15.2 - 18.3 m) - Cable Length: 66.0 ft (20.0 m)
7353.10.22M Furlers - Reflex Asymmetric Spinnaker Unit 3 - Boat Size: 44.0 - 58.0 ft (13.4 - 17.7 m) - Cable Length: 72.0 ft (22.0 m)
7351.10.18M Furlers - Reflex Asymmetric Spinnaker Unit 1 - Boat Size: 35.0 - 40.0 ft (10.6 - 12.0 m) - Cable Length: 60.0 ft (18.0 m)
7352.10.23M Furlers - Reflex Asymmetric Spinnaker Unit 2 - Boat Size: 50.0 - 60.0 ft (15.2 - 18.3 m) - Cable Length: 75.0 ft (22.9 m)
7353.10.26M Furlers - Reflex Asymmetric Spinnaker Unit 3 - Boat Size: 44.0 - 58.0 ft (13.4 - 17.7 m) - Cable Length: 85.0 ft (25.9 m)
7351.10.20M Furlers - Reflex Asymmetric Spinnaker Unit 1 - Boat Size: 35.0 - 40.0 ft (10.6 - 12.0 m) - Cable Length: 66.0 ft (20.0 m)
7352.10.25M Furlers - Reflex Asymmetric Spinnaker Unit 2 - Boat Size: 50.0 - 60.0 ft (15.2 - 18.3 m) - Cable Length: 82.0 ft (25.0 m)
7351.28 Head Swivel for Reflex Unit 1 Furlers
7352.28 Head Swivel for Reflex Unit 2 Furlers
7353.28 Head Swivel for Reflex Unit 3 Furlers
7351.26 Free Tack Adapter for Reflex Unit 1 Furlers
7352.26 Free Tack Adapter for Reflex Unit 2 Furlers
7353.26 Free Tack Adapter for Reflex Unit 3 Furlers
7351.10BASE Drum Only for Reflex Unit 1 Furlers (Attachments not included)
7352.10BASE Drum Only for Reflex Unit 2 Furlers (Attachments not included)
7353.10BASE Drum Only for Reflex Unit 3 Furlers (Attachments not included)
7371 Reflex Torsion Cable - Dia: 3/8 in (10.0 mm) - Reflex Unit 1
7372 Reflex Torsion Cable - Dia: 3/7 in (11.0 mm) - Reflex Unit 2
7373 Reflex Torsion Cable - Dia: 1/2 in (13.0 mm) - Reflex Unit 3
7357 Anti Torsion Cable Clamps - 10mm for Unit 1 Furlers
7358 Anti Torsion Cable Clamps - 11mm for Unit 2 Furlers
7367 Anti Torsion Cable Clamps - 13mm for Unit 3 Furlers
7351.20 Snap Shackle (6mm pin) & Threaded Adapter for Reflex Unit 1 Furlers
7352.20 Snap Shackle (8mm pin) & Threaded Adapter for Reflex Unit 2 Furlers
7353.20 Snap Shackle (10mm pin) & Threaded Adapter for Reflex Unit 3 Furlers
7351.27 Fixed Tack Adapter for Reflex Unit 1 Furlers
7352.27 Fixed Tack Adapter for Reflex Unit 2 Furlers
7353.27 Fixed Tack Adapter for Reflex Unit 3 Furlers
7351.21 D Shackle (6mm pin) & Threaded Adapter for Reflex Unit 1 Furlers
7352.21 D Shackle (8mm pin) & Threaded Adapter for Reflex Unit 2 Furlers
7353.21 D Shackle (10mm pin) & Threaded Adapter for Reflex Unit 3 Furlers
2109 "D" Shackle - High Resistance - Pin Dia: 1/4 in (6.0 mm)
2116 "D" Shackle - High Resistance - Pin Dia: 5/16 in (8.0 mm)
2123 "D" Shackle - High Resistance - Pin Dia: 13/32 in (10.0 mm)
7351.22 Tack Lashing Loop 2:1 Adapter for Reflex Unit 1 Furlers
7352.22 Tack Lashing Loop 2:1 Adapter for Reflex Unit 2 Furlers
7353.22 Tack Lashing Loop 2:1 Adapter for Reflex Unit 3 Furlers
7356 Stanchion Mounts - Reflex Furling Lead Block Kit
7355 Stanchion Mounts - Reflex Fairlead
7360 Stanchion Mounts - Reflex 57.0 mm (2 1/4 in) Bungee Block
7359 Stanchion Mounts - Reflex Double Cam Fairlead

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual