INSTALLATION & MAINTENANCE MANUAL

Ratios, performance, working load, weights, rope range, outline dimensions, deck and motor installation, cable sizing, planetary-gear service and the parts list for the UniPower 500 Radial winch.

DocumentHarken UniPower 500 Winch Installation & Maintenance Manual
FormatPDF · 18 pages · 2.2 MB
LanguageEnglish
UniPower 500 Winch

Specifications

Value
Power ratio (socket input) 10.7 : 1
Gear ratio (motor input) 135 : 1
Motor 400 W, 12 V or 24 V
Line speed (no load) 7 m/min (23 ft/min)
Max load 500 kg (1102 lb)
Current at MWL 180 A (12 V), 80 A (24 V)
Rope range Ø8–Ø14 mm
Dimension mm
Top Ø 159
Drum Ø 99
Height above deck 199.5
Below deck 75.9
Motor Ø 85
Base Ø 146
Version Drum Weight
A Anodized aluminium 6.7 kg (14.77 lb)
C Chrome bronze 8.2 kg (18 lb)

The theoretical power ratio does not take friction into account.

Maximum working load (MWL): 500 kg (1102 lb). Loads above the MWL can make the winch fail or pull off the deck.

Deck Mounting

  • Flat deck, reinforced if needed to take at least twice the MWL. Sheet entry angle 8° ±2°.
  • Check below-deck space for the motor, then drill a Ø112 mm cutout and drop the motor through.
  • Five M6 socket-head bolts through 6.5 mm holes on a Ø123 mm bolt circle. Mounts in any direction: no drive-gear orientation to respect.
  • A4 stainless bolts only (DIN 267 part 11), no countersunk bolts; bed in marine sealant and keep drainage channels clear.

Strip for Mounting

  • Central screw off (2 Nm, 18 in-lb), then the socket and cover.
  • Three screws (4 Nm, 35 in-lb) and the self-tailing arm, rotating and lifting it.
  • Lift off the drum and bolt the base down.
  • Position the self-tailing arm so the tail leads into the cockpit.

Electrics

  • The Dual Function Control Box is mandatory: see its manual for mounting and wiring.
  • Permanent-magnet motor: swapping the leads reverses the drum. For clockwise rotation A1 is positive, A2 negative.
  • Terminals: nut – cable terminal – self-locking washer – lock nut; do not turn the spindles; max 10 Nm (88 in-lb).
  • After assembly, press the switch and check the drum turns before sailing. Circuit breaker HCP1717 (80 A) for 12 V and 24 V.
Winch / voltage Under 5 m (16.4 ft) 5–10 m (16.4–32.8 ft) 10–15 m (32.8–49.2 ft) 15–20 m (49.2–65.6 ft)
UniPower 12V 32 mm² (AWG 2) 50 mm² (AWG 0) 70 mm² (AWG 00) 95 mm² (AWG 000)
UniPower 24V 16 mm² (AWG 5) 25 mm² (AWG 3) 35 mm² (AWG 2) 50 mm² (AWG 0)

Maintenance

Routine

  • Wash with fresh water frequently, and after every use.
  • Keep teak cleaners and caustic products off anodized, chromed and plastic parts.
  • No solvents, polishes or abrasive pastes on logos and stickers; no polishes or abrasives on anodized, chromed or plastic surfaces.
  • Keep the base holes and drainage channels clear so water cannot collect.
  • Inspect visually at the start and end of every season; full overhaul, clean and lubricate at least every 12 months.
  • Switch the power off before any maintenance.

Overhaul

  • After the mounting strip-down: six hex screws (20 Nm, 177 in-lb) and the gear carrier; mind the rollers in the gear carrier.
  • Pawl carrier, gear, second planetary assembly and flange (mind the O-ring in the ring gear), then first planetary assembly, ring gear, O-ring and pinion.
  • On assembly check the O-ring and the rollers between ring gear and flange / gear carrier, and between ring gear and base.
  • Jaws: four screws at 4 Nm (35 in-lb).
  • Grease gears and moving parts with a brush; oil pawls and springs only, never grease them.

When refitting the jaws, the peeler goes between them with the letters TOP facing up, aligned with the stripper arm. Hold each pawl spring closed, slide the pawl in, and check it opens and closes easily with a finger.

UniPower 500 Spare Parts

From the UniPower 500 A / C parts lists; the versions differ only in the drum assembly.

Harken code Pos. Description
G60982000E 1 Motor 12 V 400 W Ask us to source it →
G60983000E 1 Motor 24 V 400 W Ask us to source it →
S732590004 2 Pinion Z=9 Ask us to source it →
A97326000 3 Base assembly UniPower 500 Ask us to source it →
S450660003 4 Roller Ø5 × 10.5 Ask us to source it →
M0648397 5 Seal Ø30 × Ø38 × 4 NBR Ask us to source it →
S4129400A0 6 Stripper arm support View part →
S413380019 7 Stripper arm W46 View part →
S490780004 8 Gear Z=27 Ask us to source it →
M6004597 9 O-ring 2237 View part →
S490800080 10 Flange Ask us to source it →
S732630004 11 Pin Ø12 Ask us to source it →
S7394500A5 12 Cover UniPower 500 Ask us to source it →
M0601803 13 Screw UNI EN ISO 1207 M6 × 35 View part →
S281680097 14 Red line View part →
S000080003 15 Pawl Ø8 View part →
S000380001 16 Pawl spring Ø8 View part →
M0635103 17 Socket head screw M6 × 16 UNI 5931 View part →
S490960004 18 Pawl carrier Ask us to source it →
S732640053 19 Gear carrier Ask us to source it →
A94903900 20 Gear assembly Z=10 Ask us to source it →
S490390004 20 Gear Z=14 Ask us to source it →
A97393900 21 First planetary assembly Ask us to source it →
A97394000 22 Second planetary assembly Ask us to source it →
M6007103 23 Slotted cup head screw M6 × 50 UNI 6107 View part →
A97326500 25 Drum assembly UniPower 500 (A) Ask us to source it →
A97442800 25 Drum assembly UniPower 500 C Ask us to source it →
M0610280 25 Ball 5/16" (40 per drum) Ask us to source it →
A97326600 26 Jaws assembly UniPower 500 Ask us to source it →
S414280080 26 Peeler View part →
S385970001 26 Spring Ask us to source it →
A94136400 27 Socket assembly View part →
M0625303 29 Socket button head screw M6 × 12 ISO 7380 A4 Ask us to source it →
S011130080 30 Washer 8.5 × 16 × 1 Ask us to source it →
S732670080 31 Ring Ø72 × Ø60 × 6 Ask us to source it →

Quote the Harken part number and the winch serial number, printed on the plate on the drum support. Parts marked * are available in the Harken service kit.

Parts in this Manual We Carry

Harken part numbers as printed in the installation & maintenance manual, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual