INSTALLATION SHEET

Track fit, 4:1, 5:1 and 6:1 control-line reeving, the 3180 adapter kit, how windward sheeting works, ball replacement and maintenance for the 3176–3179 Big Boat windward sheeting cars.

DocumentHarken Windward Sheeting Cars 3176–3179 Installation Sheet
FormatPDF · 4 pages · 0.6 MB
LanguageEnglish
Windward Sheeting Cars 3176–3179

Specifications

Car Car width Track
Big Boat 3 3/8" (85 mm) 3154, 3155, 3156, 3159, 3162

3176, 3177, 3178 and 3179 are windward sheeting cars; the 3180 adapter kit converts 3163, 3164, 3165 and 3166 Big Boat CB cars. Load on the mainsheet block keeps the leeward cleat open, so the car can be pulled to windward without releasing the leeward control line.

Only CB cars roll on CB track. If the car does not roll on easily, check the track. Never remove the ball retaining wires: the car will not roll without its retaining clips.

Mounting

  • Position the car at the end of the track, sheave side aft, and roll it on gently.
  • Do not fit a stand-up spring between the mainsheet block and the windward car.
  • 3180 kit: remove the screws holding the swivel ears or control blocks on top of the car and keep them.
  • Fit the kit with the angled sheaves facing forward; a few drops of blue Loctite on the four HFS1021 screws, then tighten firmly.
  • Bumper extensions supplied with the 3169 controls go on 3160, 3163, 3176 and 3177 car bodies; pull the old bumpers with pliers and push the new ones in. Longer 7 7/16" (188 mm) cars do not need them.

Control Lines

  • 4:1 with 3168 end controls: eye splice or bowline to the inside bar of the end control, remove the vertical sheave and becket, reeve down through the angled sheave, round the end control sheave, round the top sheave and out through the cleat.
  • 5:1 with 3169 end controls: deadend to the vertical sheave, then lower end control sheave, angled car sheave (upwards), upper end control sheave, upper car sheave and out through the cam cleat.
  • 6:1 with 3169 end controls: deadend to the lower post on the end control, pass up between vertical sheave and post, then reeve as for 5:1.
  • Always tie a stop knot in the tail to prevent damage in an uncontrolled gybe.

Using the Windward Car

  • Position the car by pulling the windward traveler control line; do not release the leeward cleat to pull the car to windward.
  • Tack and the car stays; pull it to windward on the new tack without releasing the leeward control line.
  • If the car is pulled to windward and then dropped to centreline before a tack, the leeward line has slack and the car will drop below centreline on the new tack.
  • Little wind and big waves: fit Cam-Matic cam cleats on deck at the outboard ends of the track as override cleats to stop the car slatting.
  • Tie the car to one side when motoring or moored, or it can work loose and be damaged against the track ends.

Kit and Replacement Parts

Part no. Description
3180 Windward sheeting adapter kit for 3163, 3164, 3165, 3166 Big Boat CB cars View part →
610ASSY Windward sheeting assembly (in 3180 kit) Ask us to source it →
HFS1021 M6 × 1 12 mm screw, 4 per kit Ask us to source it →
833 Blue Loctite Ask us to source it →
150SP Cam-Matic cam cleat, 2 per car View part →
201 Eyestrap, 2 per car Ask us to source it →
HFS107 10-32 × 1.50 cam screw, 4 per car Ask us to source it →

Ball replacement

Ball set CB car Series Balls per car Balls Ball Ø
547 3163 / 3164 / 3176 / 3177 Big Boat 3000 50 Delrin, 25 per set 3/8" (10 mm) View part →
547 3165 / 3166 / 3178 / 3179 Big Boat 4500 72 Torlon, 25 per set 3/8" (10 mm) View part →

Load with the car on edge and the retaining clip in place: push one ball at a time through the centre of the clip, let them roll into the return race, then add the rest. Do not overfill. Unload the same way, one ball at a time; never remove the retaining clip.

Maintenance

  • Flush the cars often with fresh water; periodically squirt detergent and water into the centre openings, roll the car back and forth, then flush the bearings. Most important when the cars have not been used.
  • No spray lubricants: the balls skid instead of rolling. With a light machine oil such as 3-in-1, one drop per ball race only; too much oil attracts dirt.
  • Clean the track with detergent and water.
  • Inspect shackles and control block fittings for fatigue. Every installation needs Harken track endstops; rig the controls so the car does not hit them under load.

Parts in this Manual We Carry

Harken part numbers as printed in the installation sheet, matched to the genuine parts in our store.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual