We Ship Worldwide! Shipping information.
INSTRUCTIONS

Technical data, photometrics, item codes and fitting for the Quick Blake XP 79 × 79 mm LED down lights: FP OD and FP SD (springs), HP (screws) and LP, 4W and 6W.

DocumentQuick Blake XP LED Down Lights Technical Sheets
FormatPDF · 4 pages · 0.2 MB
LanguageEnglish
Download PDF ▾
InstructionsPDF · 4 p.Blake XP FP OD 6WPDF · 4 p.Blake XP FP SD 4WPDF · 4 p.Blake XP FP SD 6WPDF · 4 p.Blake XP HP 4WPDF · 4 p.Blake XP HP 6WPDF · 4 p.Blake XP LP 4WPDF · 4 p.Blake XP LP 6WPDF · 4 p.
View Collection
SpecificationsInstallationProducts
Quick Blake XP LED Down Lights — Technical Sheets

Technical Data

Version Fixing / recess LEDs / supply Power / absorption Beam Flux WW / DL CRI
FP OD 4W Springs, ceiling / 30 mm 1 power LED / 9-32 Vdc 4 W; 0,33A@12V – 0,17A@24V 100° 288 / 320 lm 90
FP OD 6W Springs, ceiling / 30 mm 1 power LED / 9-32 Vdc 6 W; 0,5A@12V – 0,25A@24V 100° 368 / 395 lm 90
FP SD 4W Springs, ceiling / 30 mm 1 power LED / 9-32 Vdc 4 W; 0,33A@12V – 0,17A@24V 100° 362 / 400 lm 90
FP SD 6W Springs, ceiling / 30 mm 1 power LED / 9-32 Vdc 6 W; 0,5A@12V – 0,25A@24V 100° 460 / 500 lm 90
HP 4W Screws, ceiling-wall / 28 mm 2 power LED / 10-30 Vdc neg. com. 4 W; 0,33A@12V – 0,17A@24V 60° 205 / 220 lm –
HP 6W Screws, ceiling / 28 mm 2 power LED / 10-30 Vdc neg. com. 6 W; 0,5A@12V / 0,25A@24V 60° 275 / 295 lm –
LP 4W (rev. 004/A) Springs, ceiling / 30 mm 1 power LED / 9-32 Vdc 4 W; 0,33A@12V / 0,17A@24V 95° 362 / 400 lm 90
LP 6W Springs, ceiling / 30 mm 2 power LED / 10-30 Vdc neg. com. 6 W; 0,5A@12V / 0,25A@24V 60° 275 / 295 lm –
  • All versions: 79 x 79 mm, mounting hole Ø 65 mm, 150 gr, IP66, bicolor (secondary light 0,3W where given), PWM dimming, constant-voltage supply.
  • Bezel AISI 316 / 316L stainless steel, polycarbonate diffuser, aluminium heat sink. FP and LP 4W sheets: finishes polished, white, satin or black; colours WW, DL, blue, red (LP 4W also white-blue, white-red).
  • Recommended dimmer: FASP094CA2A3D00 HDIM300 D00 (9-32 Vdc versions) or FASP094CA2A3A00 HDIM300 (10-30 Vdc versions).
  • Warm white 2900-3100 °K, daylight 3800-4100 °K. Full photometric data (lux and beam diameter at 1, 2 and 3 m) are in each datasheet.

Item codes on the sheets

Finish HP 4W HP 6W LP 6W
White DL FASP3022B01CA00 FASP3022B11CA00 FASP3012B11CA00
White WW FASP3022B02CA00 FASP3022B12CA00 FASP3012B12CA00
Satin DL FASP3022S01CA00 FASP3022S11CA00 FASP3012S11CA00
Satin WW FASP3022S02CA00 FASP3022S12CA00 FASP3012S12CA00
Mirror polished DL FASP3022X01CA00 FASP3022X11CA00 FASP3012X11CA00
Mirror polished WW FASP3022X02CA00 FASP3022X12CA00 FASP3012X12CA00

Spring-Mounted (FP OD, FP SD, LP)

  1. Cut the hole or recess to the size in the table.
  2. Bring the supply wires to the panel.
  3. Connect: red positive, black negative.
  4. Fold the springs as shown so the light enters the hole.
  5. Push the light body into the hole and turn it to the position you want.

Screw-Mounted (HP) & Wiring

  1. Cut the hole to the recommended size and bring the supply wires (at the voltage in the chart) to the panel.
  2. The wires come with male Faston connectors: cut them off if not needed. Red positive, black negative; test.
  3. Fix the light with self-tapping screws, then press the frame on.
  • Extra-low voltage (SELV) only, from a constant-voltage LED supply; never connect to AC mains. Units can be connected in parallel.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual