Quick Eagle E1 Horizontal Windlass — Installation & User's Manual
INSTALLATION MANUAL
View Collection
Technical data, cable and breaker sizing, deck installation, operation, drum use, maintenance and the coded parts list for the Quick Eagle 300 W and 500 W 12 V horizontal windlasses (E 312, E 312 D, E 512, E 512 D).
DocumentQuick Eagle E1 Horizontal Windlass Installation & User's Manual
FormatPDF · 36 pages · 1.8 MB
LanguageEnglish
Download PDF ▾
Technical Data
Model code example EAGLE312D: line EAGLE (aluminium base, horizontal axis), motor power (3 = 300 W, 5 = 500 W), voltage (12 = 12 V), drum (– = without, D = with).
| 300 W | 500 W | |
|---|---|---|
| Motor supply voltage | 12 V | 12 V |
| Maximum pull | 380 kg (837,5 lb) | 630 kg (1388,9 lb) |
| Maximum working load | 100 kg (220,5 lb) | 250 kg (551,1 lb) |
| Working load | 30 kg (66,1 lb) | 80 kg (176,4 lb) |
| Current at working load | 60 A | 90 A |
| Maximum chain speed | 26,3 m/min (86.3 ft/min) | 26,3 m/min (86.5 ft/min) |
| Chain speed at working load | 22,5 m/min (73.8 ft/min) | 16,2 m/min (53 ft/min) |
| Motor cable size | 16 mm² (AWG5) | 16 mm² (AWG5) |
| Protection circuit breaker | 50 A | 60 A |
| Deck thickness | 20 ÷ 40 mm (25/32" ÷ 1" 9/16) | 20 ÷ 40 mm (25/32" ÷ 1" 9/16) |
| Weight without drum | 8,0 kg (17,6 lb) | 8,0 kg (17,6 lb) |
| Weight with drum | 9,3 kg (20,5 lb) | 9,3 kg (20,5 lb) |
| Gypsy | Chain |
|---|---|
| 6 mm | 6 mm DIN 766, 6 mm ISO (ISO EN 818-3) |
Current after an initial period of use; speeds with a gypsy for 6 mm chain. Cable size is the minimum for a total run L= < 20m: size up for longer runs. Breaker: DC, delayed-action (thermal-magnetic or hydraulic-magnetic). Shafts and studs for thicker decks on request.
Before You Drill
- In the box: windlass, contactor unit, base gasket, drill template, handle, fasteners, manual.
- Tools: Ø 6 mm (15/64") and Ø 9 mm (23/64") drills; Ø 48 and Ø 92 mm (3" 1/2) hollow mills; 10 mm and 13 mm wrenches.
- Recommended: RL control board (mod. 800), HRC1002 hand-held remote, foot switch (mod. 900), hydraulic-magnetic breaker, chain counter CHC1102M / CHC1202M, RRC radio (R02, P02, H02).
- Align the gypsy with the bow roller; keep the deck faces parallel; deck thickness within the table range.
- No obstructions under deck for cables and chain; a shallow peak causes jamming. The installation drawing shows 40 cm (16") below deck and a max 5 mm (3/16") gap.
Fitting
- Drill the four holes with the drilling template and clear the chain hole.
- Lower the windlass into place from above deck with the gasket between deck and base.
- Screw the studs into the base by their short threaded end, using a medium-grade thread locker.
- Tighten the nuts on the studs.
- Connect the supply cables to the reversing contactor.
Electrical System
- Reversing contactor unit T6415-12 (12V); L = L1 + L2 + L3 + L4 + L5 for cable sizing.
- Control fuse 4A (12V) / 2A (24V).
- Controls shown: HRC 1002 hand-held remote, 900U and 900D foot switches, control board mod. 800, chain counters CHC1102 M and CHC1202 M, RRC receiver R02 (2CH).
- Mount the reversing contactor where water cannot reach it.
Operation
Weighing and Casting
- Clutch (3) links gypsy and shaft (13 or 17): handle (1) in the gypsy cover (2), counter-clockwise to disengage, clockwise to engage.
- Weighing: engine on, clutch engaged, handle out, press UP; watch the last metres to protect the bow.
- If it stops without tripping the breaker, wait a few seconds and retry; if the breaker trips, reset it and wait a few minutes; if still blocked, move the boat to free the anchor.
- Casting: clutch disengaged for free fall, handle clockwise to slow the chain; or press DOWN for a controlled run-out.
- At anchor, secure the chain with a rope or stopper.
Drum Use
- Secure the anchor and chain to a bitt or strong point first.
- Release the clutch with the handle (at least 2 turns of the bush anticlockwise), remove the handle from the bush (20) on the drum (19).
- At least 3 turns of rope on the drum; keep hands clear during take up.
- When done, retighten the clutch clockwise and make the rope fast.
Never run the motor with the handle in the drum or gypsy cover; isolate the motor when working by hand.
Maintenance
- Power off; take the chain off the gypsy or the rope off the drum.
- Wash salt deposits off with fresh water regularly.
- Once a year, all versions: remove the gypsy cover (2) with the handle (1), then the top clutch cone (3); loosen screws (21) and remove the chain stripper (9); pull off the gypsy (4). Clean and grease the shaft thread (13 and 17) and the clutch cone seat (3).
- Drum: loosen the bush (20) with the handle, pull off the drum (19), clean and grease the shaft (13 or 17).
- Clean and grease the motor and reversing contactor terminals.
Exploded View and Parts List
| Quick code | Pos. | Description | |
|---|---|---|---|
| PVLVSDN00000 | 1 | Straight windlass lever – nylon | Ask us to source it → |
| SPMVGB040R02 | 2 | Gypsy cover | Ask us to source it → |
| MSF04R100000 | 3 | Clutch cone | Ask us to source it → |
| ZSB040600000 | 4 | Gypsy | Ask us to source it → |
| KPMC08060000 | 5 | Magnet | Ask us to source it → |
| MBAC1720Y000 | 6 | Circlip | Ask us to source it → |
| MBAE1715Y000 | 7 | External circlip | Ask us to source it → |
| PGPRL3047700 | 8 | Oil seal | Ask us to source it → |
| MSN04RX00000 | 9 | Rope/chain stripper Eagle | Ask us to source it → |
| SGMSC04R0000 | 10 | Base Eagle | Ask us to source it → |
| MBJ160060000 | 11 | Bearing | Ask us to source it → |
| MSLCR0400000 | 12 | Crown gear | Ask us to source it → |
| MSAR04112000 | 13 | Short shaft | Ask us to source it → |
| MBH0606025X0 | 14 | Shaft key – stainless steel | Ask us to source it → |
| SGMSGR04C000 | 15 | Base cover | Ask us to source it → |
| MBV0512MXTSC | 16 | Screw | Ask us to source it → |
| MSAR04155000 | 17 | Long shaft | Ask us to source it → |
| SGMSGR04A000 | 18 | Base flange | Ask us to source it → |
| MSE040000R02 | 19 | Drum | Ask us to source it → |
| SGMSD0400000 | 20 | Bush | Ask us to source it → |
| MBV0510MXCE0 | 21 | Screw | Ask us to source it → |
| KNREEDCL0000 | 22 | Sensor | Ask us to source it → |
| PGBSR0400000 | 23 | Seal / template | Ask us to source it → |
| MBP080608X00 | 24 | Studs | Ask us to source it → |
| MBR08X000000 | 25 | Washers | Ask us to source it → |
| MBR08XDE0000 | 26 | Grower | Ask us to source it → |
| MBD08MXEN000 | 27 | Nuts | Ask us to source it → |
| MBJHK1212000 | 28 | Bearing | Ask us to source it → |
| MSLVT0400000 | 29 | Worm screw | Ask us to source it → |
| MBJ7204BE000 | 30 | Thrust bearing | Ask us to source it → |
| MBAN4717Y000 | 31 | Internal circlip | Ask us to source it → |
| PGPRL2047700 | 32 | Oil seal | Ask us to source it → |
| EMF051200000 | 33A | Electric motor 500W 12V | Ask us to source it → |
| EMF031200000 | 33B | Electric motor 300W 12V | Ask us to source it → |
| MBH040415F00 | 34 | Shaft key | Ask us to source it → |
| PGGPMFN04000 | 35 | Flange gasket | Ask us to source it → |
| PCCCPM040000 | 36 | Motor casing watertight | Ask us to source it → |
| PGGPMPM04000 | 37 | Poles gasket | Ask us to source it → |
| PCCPPMFN0400 | 38 | Bottom protec cover | Ask us to source it → |
| MBV03916AXCC | 39 | Screw | Ask us to source it → |
Drilling Template
- The Eagle 300/500 drilling template (extra download, A3, scale 1:1) shows the stud holes, the Ø92 and Ø48 holes and the bow direction, with a 100 mm / 4" check bar.
- Print at 100% (no "fit to page") and measure the check bar before drilling.
Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.
Products in this Manual
-
Quick Windlass - Eagle E1 500W Horizontal Electric 12V Gypsy + Drum 6mm - ISO
QCKFSE00512D006A00
$1,524.00 USDList Price: $2,009.44 USDUnit price /Unavailable -
Quick Windlass - Eagle E1 500W Horizontal Electric 12V Gypsy Only 6mm - ISO
QCKFSE005120006A00
$1,391.00 USDList Price: $1,770.45 USDUnit price /Unavailable -
Quick Windlass - Eagle E1 300W Horizontal Electric 12V Gypsy Only 6mm - ISO
QCKFSE003120006A00
$1,358.00 USDList Price: $1,729.50 USDUnit price /Unavailable
