Quick Eagle E3 Horizontal Windlass (PDF)

INSTALLATION MANUAL

Technical data, gypsy/chain match, cable and breaker sizing, deck installation, clutch, drum and anchoring procedures, annual service and the coded parts list for the Quick Eagle 700, 1000 and 1400 W horizontal windlasses (aluminium base, with drum).

DocumentQuick Eagle E3 Horizontal Windlass Installation & User's Manual

FormatPDF · 36 pages · 2.0 MB

LanguageEnglish

Download PDF ▾

View Collection

Specifications Electrical Installation Operation Maintenance Parts Drill Template Products

Quick Eagle E3 Horizontal Windlass — Installation & User's Manual

Technical Data

Model code example EAGLE 7 12 D: line (Eagle = aluminium base, horizontal axis) – motor power (7 = 700 W, 10 = 1000 W, 14 = 1400 W) – supply voltage (12 = 12 V, 24 = 24 V) – D = with drum.

	700 W 12 V	700 W 24 V	1000 W 12 V	1000 W 24 V	1400 W 12 V	1400 W 24 V
Maximum pull	1070 kg 2358,9 lb		1250 kg 2755,8 lb		1450 kg 3196,7 lb
Maximum working load	300 kg 661,4 lb	370 kg 815,7 lb	390 kg 859,8 lb	490 kg 1080,3 lb	450 kg 992,1 lb	500 kg 1102,3 lb
Working load	100 kg 220,5 lb	125 kg 275,6 lb	130 kg 286,6 lb	160 kg 352,7 lb	150 kg 330,7 lb	185 kg 407,8 lb
Current at working load (1)	90 A	60 A	140 A	80 A	150 A	85 A
Maximum chain speed (2)	28,7 m/min 94,2 ft/min	33,5 m/min 109,9 ft/min	37,6 m/min 123,4 ft/min	47,8 m/min 156,8 ft/min	37,6 m/min 123,4 ft/min	47,8 m/min 156,8 ft/min
Chain speed at working load (2)	15,8 m/min 51,8 ft/min	15,0 m/min 49,2 ft/min	17,8 m/min 58,4 ft/min	20,9 m/min 68,6 ft/min	17,5 m/min 57,4 ft/min	18,7 m/min 61,4 ft/min
Motor cable size (3)	25 mm² AWG 3	10 mm² AWG 7	35 mm² AWG 2	16 mm² AWG 5	50 mm² AWG 0	25 mm² AWG 3
Protection circuit breaker (4)	60 A	40 A	80 A	50 A	100 A	50 A
Weight, model with drum	22,6 kg 49,8 lb		23,7 kg 52,2 lb		23,7 kg 52,2 lb

Maximum pull and weight are given once per motor power (both voltages). Deck thickness: 35 ÷ 65 mm (1" 3/8 ÷ 2" 9/16). (1) After an initial period of use. (2) With a gypsy for 8 mm chain. (3) Minimum value for a total cable length L ≤ 20 m; size the cable for the actual run. (4) DC circuit breaker, delayed-action (thermal-magnetic or hydraulic-magnetic). Studs for thicker decks are available on request.

Gypsy	Chain size
6 mm	DIN 766, ISO EN 818-3
8 mm – 5/16"	DIN 766, ISO EN 818-3, G4, BBB
10 mm – 3/8"	DIN 766, ISO EN 818-3, G4

Dimensions mm (inch)

Height above deck: 205 (8 3/32), both versions.
Below deck: 195 (7 21/32) on the Eagle 700W D; 210 (8 1/4) on the Eagle 1000/1400W D; motor housing width 150 (5 29/32).
Base: 295 (11 5/8) × 239.4 (9 27/64).

Electrical System

Motor feed: battery → hydraulic-magnetic circuit breaker (rated per the table) → contactor unit → motor. Cable size is for the total length L = L1 + L2 + L3 + L4.
Contactor unit supplied: mod. T6315-12 (12 V) or T6315-24 (the 24 V unit is also labelled "12V" in the diagram, as printed). Install it where it is protected from water.
Control circuit fuse: 4 A (12 V), 2 A (24 V).
Controls wire to the contactor with black, brown and blue leads; the main connection diagram adds the chain counter sensor.
Recommended Quick accessories: RL control board (mod. 800), watertight hand-held remote HRC 1002, foot switches 900U/900D, hydraulic-magnetic circuit breaker, chain counters CHC1102M and CHC1202M, RRC radio controls (R02 receiver, P02/H02 transmitters).
Fit at least two controls, so the windlass can still be run if one is damaged. View HRC 1002 →

Before You Drill

In the box: windlass, contactor unit, base gasket, drill template, handle, bolts and screws, manual, warranty.
Tools: drill with Ø 9 mm (23/64") bit, Ø 51 mm (2") and Ø 127 mm (5") hollow mills, 13 mm hex wrench.
Align the gypsy with the bow roller.
Upper and lower deck faces as parallel as possible; compensate if not, or the motor loses power.
Deck thickness must fall within the table range; otherwise consult a Quick dealer.
No obstacles under deck for cables and chain; the drawing shows 40 cm (16") of chain fall to the heap. A shallow chain locker causes jamming.

Fitting Procedure

Drill the four holes with the drill template.
Open the chain hole so the chain runs free; the drawing shows the hole edge finished at 45°.
Lower the windlass from above deck with the gasket between deck and base.
Screw the studs into the base by their short threaded end, with medium-strength thread locker.
Fit the nuts on the studs, then connect the windlass cables to the contactor.

Operation

Clutch, Weighing and Casting

Clutch: handle (1) in the gypsy cover (2); counter-clockwise releases the clutch (3), clockwise re-engages it.
Weighing: engine on, clutch engaged, handle removed, press UP. If the windlass stops and the breaker has not tripped, wait a few seconds and retry; do not hold the button down.
If the breaker trips, reset it and wait a few minutes. If it stays blocked, move the boat to free the anchor. Watch the last metres of chain to protect the bow.
Casting electrically: press DOWN; the chain pays out evenly under control.
Casting manually: release the clutch and let the gypsy run; turn the handle clockwise to slow the chain.

Drum and Safety

Before warping, make the anchor and chain fast to a bitt or strong point.
Drum (21) on its own: release the clutch at least 2 turns of the gypsy cover anticlockwise, remove the handle, take at least 3 turns of rope on the drum. Keep hands clear.
When finished, tighten the gypsy cover clockwise and make the rope fast.
Never run the motor with the handle in the drum or gypsy cover; switch the motor off for any manual work.
At anchor and under way, hold the chain on a stopper or bollard and switch the breaker off; the windlass is not designed for storm loads.

Maintenance

Switch off the motor power first, then remove the chain or rope from the gypsy and the rope from the drum.
Wash salt deposits off with fresh water regularly.
Once a year, gypsy side: handle (1) off the gypsy cover (2), remove the top clutch cone (3), undo the screws (11) of the stripper (9), remove it and pull off the gypsy (4). Clean, then grease the shaft thread (17) and the gypsy seats of the clutch cones with marine grease.
Drum side: loosen the bush (22) with the handle, pull off the drum (21), clean and grease the shaft (17).
Clean any oxide off the motor and contactor terminals and grease them.

Quick Eagle E3 700/1000/1400 W exploded view

Parts List

Code	Pos.	Description
ZSLMSHR10000	1	Bent anchor winch lever	Ask us to source it →
SPMSGB100R02	2	Gypsy cover	Ask us to source it →
MSF100000000	3	Clutch cone	Ask us to source it →
ZSB100600000	4A	Gypsy 6 mm	Ask us to source it →
ZSB1008516E4	4B	Gypsy 8 mm – 5/16"	Ask us to source it →
ZSB1010380AR	4C	Gypsy 10 mm – 3/8"	Ask us to source it →
KPMC08060000	5	Magnet	Ask us to source it →
MBR254025X00	6	Spring washer	Ask us to source it →
MBAE2520Y000	7	External circlip	Ask us to source it →
PGPRL4056800	8	Oil seal	Ask us to source it →
MSN10RXR1000	9	Rope/chain stripper Eagle	Ask us to source it →
MBG06X000000	10	Spring washer	Ask us to source it →
MBV0514MXCE0	11	Screw	Ask us to source it →
MBV0514MXE00	12	Screw	Ask us to source it →
MBD06MXENC00	13	Nut	Ask us to source it →
SGMSC10R0000	14	Base Eagle	Ask us to source it →
MBJ160080000	15	Bearing	Ask us to source it →
MSLCR1000000	16	Crown gear	Ask us to source it →
MSAR10199R00	17	Shaft	Ask us to source it →
MBH0807060X0	18	Shaft key	Ask us to source it →
SGMSGR10A000	19	Base flange	Ask us to source it →
MBV0516MXSC0	20	Screw	Ask us to source it →
SPMSE10ALR01	21	Drum "AL" stainless steel	Ask us to source it →
SGMSDCPAL100	22	Bush drum	Ask us to source it →
PGR031650000	23	O-ring	Ask us to source it →
KNREEDCL0000	24	Sensor	Ask us to source it →
PGBSR1000000	25	Gasket	Ask us to source it →
MSLBC2000000	26	Bush	Ask us to source it →
MSLVT1000000	27	Worm screw	Ask us to source it →
MBJ7205BE000	28	Thrust bearing	Ask us to source it →
MBAN5220Y000	29	Internal circlip	Ask us to source it →
PGPRL2552100	30	Oil seal	Ask us to source it →
EMF071200000	31A	Electric motor 700W 12V	Ask us to source it →
EMF072400000	31B	Electric motor 700W 24V	Ask us to source it →
EMF101200000	31C	Electric motor 1000W 12V	Ask us to source it →
EMF102400000	31D	Electric motor 1000W 24V	Ask us to source it →
EMF141200000	31E	Electric motor 1400W 12V	Ask us to source it →
EMF142400000	31F	Electric motor 1400W 24V	Ask us to source it →
MBH050515F00	32	Key	Ask us to source it →
PCCCPM070000	33A	Motor casing watertight 700W	Ask us to source it →
PCCCPM100000	33B	Motor casing watertight 1000–1400W	Ask us to source it →
PCGPMMR00000	34	Grommet	Ask us to source it →
PCCPPMMR0000	35	Terminal board cover	Ask us to source it →
MBV02213AXSC	36	Screw	Ask us to source it →
PGGPMFN00000	37	Bottom gasket	Ask us to source it →
PCCPPMFN0000	38	Bottom protection cover	Ask us to source it →
PPM20B000000	39	Cable outlet	Ask us to source it →
MBP080608X00	40	Studs	Ask us to source it →
MBR08X000000	41	Washer	Ask us to source it →
MBR08XDE0000	42	Toothed washer	Ask us to source it →
MBD08MXEN000	43	Nut	Ask us to source it →

Drill Template

The A3 drilling template (scale 1:1) for the Eagle 700/1000/1400W is in the downloads: it marks the four Ø 9 mm stud holes, the chain cut-outs and the bow direction. Print it at 100% and check the 100 mm / 4" scale bar before drilling.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.