We Ship Worldwide! Shipping information.
INSTRUCTIONS

Quick Kor XP LED down light technical sheets (HP screw-mounted and LP spring-mounted, 4W and 6W): cut-out, recess, current draw, light output and wiring.

DocumentQuick Kor XP LED Down Lights Technical Sheets
FormatPDF · 4 pages · 0.5 MB
LanguageEnglish
Download PDF ▾
InstructionsPDF · 4 p.Kor XP HP 6WPDF · 4 p.Kor XP LP 4WPDF · 4 p.Kor XP LP 6WPDF · 4 p.
View Collection
SpecificationsLight OutputInstallationProducts
Quick Kor XP LED Down Lights — Technical Sheets

Range at a Glance

Model Power Supply Current Bezel size Mounting hole Recess IP Fixing Installation
KOR XP HP 4W 4 W 9-32 Vdc 0,33A@12V / 0,17A@24V Ø 82 mm Ø 65 mm 28 mm IP66 Screws Ceiling
KOR XP HP 6W 6 W 9-32 Vdc 0,5A @ 12V / 0,25A @ 24V Ø 82 mm Ø 65 mm 28 mm IP66 Screws Ceiling
KOR XP LP 4W 4 W 9-32 Vdc 0,33A@12V / 0,17A@24V Ø 82 mm Ø 65 mm 30 mm IP66 Springs Ceiling
KOR XP LP 6W 6 W 9-32 Vdc 0,5A@12V / 0,25A@24V Ø 82 mm Ø 65 mm 30 mm IP66 Springs Ceiling
  • All versions weigh 150 g. Bezel AISI 316 stainless steel; polycarbonate diffuser, aluminium heat sink.
  • Bezel finishes: polished / satin / white 9010 / gold PVD / black.
  • Bicolor with 0,3 W secondary light power. Dimmable (PWM); recommended dimmer on the sheets: FASP094CA2A3D00 HDIM300 D00.

Photometric Data

Model Light source Light type Warm white (2900–3100 K) Day light (3800–4100 K) Beam angle
KOR XP HP 4W 1 high luminosity LED Bicolor 362 lm 400 lm 95°
KOR XP HP 6W 1 high luminosity LED Bicolor 460 lm 500 lm 95°
KOR XP LP 4W 1 high luminosity LED Bicolor 362 lm 400 lm 95°
KOR XP LP 6W 1 high luminosity LED Bicolor 460 lm 500 lm 95°

Luminous flux as printed on each sheet.

Installation & Wiring

LP (springs)

  1. Cut the Ø 65 mm hole.
  2. Bring the power supply wires to the panel or ceiling.
  3. Connect: red is positive, black is negative.
  4. Position the springs as shown on the sheet so the light enters the hole.
  5. Push the light body in, turning it to the desired position.

HP (screws)

  1. Bring the power supply wires (at the voltage in the chart) to the panel.
  2. Cut the hole to the recommended size.
  3. Fit the gasket before connecting.
  4. The wires come with male fast-on connectors; cut them off if not needed. Red positive, black negative; test the light.
  5. Fix the light to the panel with self-tapping screws.
  6. Press the frame onto the light.
  • Use the unit in ultra-low voltage (SELV) with a LED power supply with constant voltage output.
  • Do not plug the unit directly into the wall socket (AC).
  • More than one unit: connect in parallel on a constant-voltage LED power supply.
  • Positive is the red wire, negative is the black wire.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual