We Ship Worldwide! Shipping information.
INSTALLATION MANUAL

Technical data, dimensions, installation of the reel (PTR) and strap (PTG) versions on deck or on a wall, wiring with the recommended controls, care and the parts list for the Quick Pontoon PT 350, 700 and 1000 on-deck windlasses.

DocumentQuick Pontoon PT 350, 700 & 1000 On-Deck Windlass Installation & User's Manual
FormatPDF · 56 pages · 5.0 MB
LanguageEnglish
Download PDF ▾
Installation ManualPDF · 56 p.Drill template PTR 350/700/1000 (1:1)PDF · 1 p.
View Collection
SpecificationsElectricalInstallationMaintenancePartsDrill TemplateProducts
Quick Pontoon PT 350, 700 & 1000 On-Deck Windlass — Installation & User's Manual

Technical Data

The model number is not the motor output: PT 350 = 150 W, PT 700 = 250 W, PT 1000 = 350 W. R = reel (anchor rode), G = flat strap (lifting a tender).

PT 350 R / PT 350 G PT 700 R / PT 700 G PT 1000 R / PT 1000 G
Motor output 150 W 250 W 350 W
Supply voltage 12 V 12 V 24 V
Maximum pull 260 kg
573,2 lb 		600 kg
1322,7 lb 		750 kg
1653,4 lb
Maximum working load 100 kg
220,4 lb 		220 kg
485,0 lb 		250 kg
551,0 lb
Working load 40 kg
88,1 lb 		80 kg
176,3 lb 		100 kg
220,4 lb
Current at working load (1) 13 A 22 A 16 A
Maximum chain speed (2) 20,8 m/min
68,2 ft/min 		20,8 m/min
68,2 ft/min 		21,5 m/min
70,5 ft/min
Chain speed at working load (2) 19,3 m/min
63,3 ft/min 		18,1 m/min
59,3 ft/min 		18,3 m/min
60,0 ft/min
Motor cable size (3) 10 mm² (AWG 7) 10 mm² (AWG 7) 10 mm² (AWG 7)
Protection circuit breaker (4) 20 A 30 A 20 A
Weight 10 kg
22 lb 		10,2 kg
22,4 lb 		10,2 kg
22,4 lb

Deck thickness: 20 ÷ 40 mm (3/4" ÷ 1" 9/16). (1) After an initial period of use. (2) Measured with 6 mm rope. (3) Minimum value for a total cable length L ≤ 20 m; size the cable for the actual run. (4) DC circuit breaker, delayed-action (thermal-magnetic or hydraulic-magnetic). Studs for thicker decks on request.

Dimensions mm (inch)

  • PT R and PT G: 294 (11 37/64), 173 (6 13/16) and 220 (8 43/64).
  • PTR with the bow-roller accessory (as printed: only models 350 – 1000): 596 (23 29/64) overall length; other dimensions 308 (12 9/64), 231 (9 7/64), 148 (5 53/64), 220 (8 43/64).

Electrical System

  • PT 350 R / PT 350 G: the reversing contactor is integrated; wire battery → hydraulic-magnetic circuit breaker → windlass. Cable size is for L = L1 + L2 + L3.
  • PT 700 / PT 1000 (R and G): a separate reversing contactor unit is supplied, shown as mod. T6411-12 (12V) in the diagrams (also for the 24 V PT 1000, as printed). Cable size is for L = L1 + L2 + L3 + L4 + L5. Install the contactor away from water.
  • Control circuit fuse: 4 A (12 V), 2 A (24 V).
  • Recommended Quick accessories: RL control board (mod. 800 – WCS 810), watertight hand-held remote HRC1002, foot switch (mod. 900, 900U/900D), strap-roller with spring catch (PTG only), hydraulic-magnetic circuit breaker, chain counter CHC 1102 M, RRC radio control (R02, P02, H02).
  • Fit at least two controls, so the windlass can still be run if one is damaged. View HRC 1002 →

Before You Drill

  • In the box: PTR or PTG windlass, reversing contactor unit (700/1000 only), 30 m (98 ft) Dyneema "chain" (PTR only, as printed), drill template, bolts and screws, manual, warranty.
  • Tools: Ø 9 mm (23/64") and Ø 15 mm (63/64", as printed) drill bits; 13 mm hex wrench.
  • PTG: align the flat strap (the windlass centre) with the hook of the tender to be lifted.
  • PTR: align the reel with the bow roller; the roller must lean out past the bow (or stern) so the anchor runs up and down without obstruction.
  • Upper and lower deck faces as parallel as possible, or the installation may be unsafe; deck thickness within the table range, otherwise consult a Quick dealer.

Fitting Procedure

  • Choose on-deck or wall mounting, then drill with the drill template.
  • Open the passage, then finish and seal it (marine paint, gel coat or two-pack epoxy).
  • Position the windlass with a clear run for the power and control cables, and screw the studs into it.
  • Connect the windlass cables to the reversing contactor unit, or to the battery where the contactor is integrated.

Safety and Maintenance

  • The PT is built to weigh the anchor; it is not designed for storm loads. Switch it off when not in use and check for swimmers before dropping anchor.
  • At anchor, make the rope fast to a stopper or bollard; the windlass must not be the only securing device. Under way, switch the breaker off and secure the rope.
  • Switch off the motor power before any manual work and take the rope off the reel.
  • Wash salt deposits off with fresh water regularly.

Quick Pontoon PT 350/700/1000 exploded view

Parts List

Pos. Description
1 Screw
2 Windlass casing "PT Plast" series
3 Plug
4 Nut
5 Washer
6 Gear Z100 M1.5
7 Gear Z20 M1.5
8 Gear Z80 M1
9 Gear Z16 M1
10 PT spacer
11 Internal circlip
12 Bearing
13 External circlip
14 Internal circlip
15 Bearing
16 Screw
17 Screw
18 Windlass base PT series
19 Plug L
20 Oil seal
21 Windlass extruded PT series
22 Cable outlet PT
23 Shaft PT 1 series
24 Shaft PT 2 series
25 Shaft PT 3 series
26A Windlass motor 150W 12V PT
26B Windlass motor 250W 12V PT
26C Windlass motor 350W 24V PT
27 Nut
28 Screw
29 Windlass reel "PT Plast" series
30 Windlass base PT series
31 Microswitch button 16A/250W
32 Reversing contactor card 45A
33 Screw
34 Gear Z100 M1
35 Gear Z20 M1
36 Complete bow roller PT stainless steel
37 Screw
38 Screw
39 Cover base PT series stainless steel

The parts list gives descriptions only; ask us with the model (PT 350, 700 or 1000, R or G) and the serial number on the product label.

Drill Template

The Pontoon series drilling template (PTR 350/700/1000) is in the downloads, with the Ø 9 mm stud holes and the cut-out. Print it at 100% and check the 100 mm reference line before drilling.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual