We Ship Worldwide! Shipping information.
INSTALLATION MANUAL

Technical data, installation, wiring, use, maintenance and spare parts for the Quick Rider R series round-base vertical windlasses: R1 P 500 W, R3 P 700/1000 W and R3 1400 W, with the R1 and R3 drilling templates.

DocumentQuick Rider R1P, R3P & R3 Vertical Windlass Installation & User's Manual
FormatPDF · 24 pages · 2.5 MB
LanguageEnglish
Download PDF ▾
Installation ManualPDF · 24 p.Drill template R1 300/500 (A4, 1:1)PDF · 1 p.Drill template R3 700/1000/1400 (A3, 1:1)PDF · 1 p.
View Collection
SpecificationsInstallationDrill TemplatesWiringUseMaintenanceSpare PartsProducts
Quick Rider R1P, R3P & R3 Vertical Windlass — Installation & User's Manual

Technical Data

Model code example R1 P 5 12 D: series, gearbox (P = technopolymer, – = aluminium), power, voltage (V), D = drum / – = no drum.

R1 P 500W 12V R1 P 500W 24V R1 P HI SPEED 12V R1 P HI SPEED 24V R3 1400W 12V R3 1400W 24V
Max instantaneous pull 660 kg (1455,0 lb) 660 kg (1455,0 lb) 600 kg (1322,8 lb) 600 kg (1322,8 lb) 1100 Kg (2425,1 lb) 1100 Kg (2425,1 lb)
Max work load 200 kg (440,9 lb) 220 kg (485,0 lb) 170 kg (374,8 lb) 200 kg (440,9 lb) 470 kg (1036,2 lb) 540 kg (1190,5 lb)
Work load 65 kg (143,3 lb) 70 kg (154,3 lb) 65 kg (143,3 lb) 70 kg (154,3 lb) 160 Kg (352,7 lb) 180 kg (396,8 lb)
Current at work load 80 A 40 A 100 A 50 A 155 A 85 A
Max recovery speed 25,2 m/min (83,0 ft/min) 25,2 m/min (83,0 ft/min) 39,0 m/min (128,0 ft/min) 39,0 m/min (128,0 ft/min) 29,2 m/min (95,8 ft/min) 29,7 m/min (97,4 ft/min)
Speed at work load 18,5 m/min (60,7 ft/min) 19,3 m/min (63,3 ft/min) 28,5 m/min (93,5 ft/min) 28,0 m/min (91,8 ft/min) 16,3 (53,5 ft/min) 19,0 (62,3 ft/min)
Min. motor cable section 16 mm² (AWG7) (as printed) 10 mm² (AWG7) 25 mm² (AWG3) 10 mm² (AWG7) 50 mm² (AWG0) 25 mm² (AWG7)
Circuit breaker 60 A 40 A 80 A 40 A 100 A 50 A
Deck thickness 20 ÷ 30 mm 20 ÷ 30 mm 20 ÷ 30 mm 20 ÷ 30 mm 30 ÷ 50 mm (1" 3/16" ÷ 1" 31/32) 30 ÷ 50 mm
Weight without / with drum 8,5 / 9,4 Kg 8,5 / 9,4 Kg 8,5 / 9,4 Kg 8,5 / 9,4 Kg 21,7 / 23,6 Kg (47,8 / 52 lb) 21,7 / 23,6 Kg

R3 P 700 / 1000 W: weight without drum 16,8 / 17,9 Kg, with drum 18,7 / 19,8 Kg. In this edition the R3 P data table repeats the R1 P 500 W performance figures, so it is not reproduced here – ask us for the R3 P 700/1000 W performance data.

Current after an initial period of use; R1 speeds with a 6 mm chain gypsy, R3 with 8 mm. Cable section is the minimum for L < 20 m. HI SPEED only on request. Shafts and studs for thicker decks on request.

Model Gypsy Chain Rope
R1 6 mm 6mm DIN 766, 6mm ISO –
R1 1/4" 1/4" BBB –
R3 6 mm 6mm DIN 766, 6mm ISO 1/2" (12,7 mm)
R3 8 mm - 5/16" 8 mm DIN 766, 8 mm ISO, 5/16" G4, 5/16" BBB 1/2" (12.7 mm) - 9/16" (14.2 mm) - 5/8" (15.8 mm)
R3 10 mm - 3/8" 10mm ISO (P.30), 3/8" G4 5/8" (15.8 mm)

Rope sizes apply to rope and chain spliced with the Quick system.

In the Box & Tools

  • Windlass (top + gearmotor); reversing contactor box (R1 500W) or contactor box (R3 700-1000-1400W); base gasket; lever; assembly screws; manual, warranty and drilling template.
  • R1 (headed "DP1" in the manual): drill Ø 9 mm (23/64") and Ø 11 mm (7/16"); hole saw Ø 50 mm; 10 and 13 mm wrenches.
  • R3 (headed "DP3"): drill Ø 9 mm and Ø 16 mm (5/8"); hole saw Ø 60 mm; 13 mm wrench.

Requirements & Fitting

  • Align the gypsy with the bow roller; positive chain tilt up to 10° at the roller and up to 5° to the deck.
  • Deck faces flat and parallel before tightening the nuts; thickness within the table; no obstructions below deck (the drawing shows 40 cm (16") of drop).
  • Drill with the template (R3: cutting area and sensor hole are marked), seal the chain hole (marine paint, gel coat or epoxy), fit the gasket, join top and gearbox, tighten the stud nuts (8÷10 Nm in the drawing) and wire up.
  • 700/1000/1400 W: the gearbox flange fits either side (flange screws 3÷4,5 Nm, same overall dimensions); motorgearbox rotates every 45° on the base.

Rider Drilling Templates

R1 300/500W (A4) mm inch R3 700/1000/1400W (A3) mm inch
A Ø9 Ø23/64 Ø9 Ø23/64
B Ø11 Ø7/16 Ø11 Ø7/16
C Ø50 Ø1"31/32 Ø60 Ø2"5/16
D Ø120 Ø4"23/32 Ø155 Ø6"7/64
E 36 1"27/64 53 2"5/64

A = four fixing holes, B = single hole, C = central cut-out, D = base outline, E = hole offset from the centreline. Both sheets are 1:1: print at 100% and check the 4" / 100 mm scale bar before drilling.

Wiring

  • R1 500 W: reversing contactor box T6415-12 (12V) / T6415-24 (24V); L = L1 + L2 + L3 + L4 + L5.
  • R3 700/1000/1400 W: contactor box T6315-12 (12V) / T6315-24 (24V); L = L1 + L2 + L3 + L4.
  • Control fuse 4A (12V) / 2A (24V); WCB hydraulic-magnetic breaker per the data table.
  • Controls shown: WCS 820 / WCS B / WCS 830, HRC 1002, 900U/900D foot switches, CHC 1103 / CHC 1203 / QNC CHC counters, RRC R02 / P02 / H02.

Cautions, Use & Troubleshooting

  • Quick windlasses are designed to weigh the anchor only, not to hold loads from storm conditions. Always deactivate the windlass when not in use and check for swimmers before dropping anchor.
  • Fit at least two controls in case one is damaged; use a Quick hydraulic-magnetic (or thermal-magnetic) delayed-action DC breaker as motor protection – it also isolates the control circuit.
  • Mount the (reversing) contactor box where it is protected from water.
  • Once anchored, take the chain onto a chain stopper or bollard; the windlass must never be the only securing device. Isolate it during navigation and secure the chain to a fixed point.
  • Make sure the motor cannot be powered when working the windlass by hand: a remote control (handheld or radio) could start it. Never run it electrically with the handle in the drum or gypsy cover.

Clutch

The clutch cones link the gypsy to the main shaft. Insert the handle in the drum bush or gypsy cover and turn it counter-clockwise to release the clutch; clockwise to re-engage it.

Weighing & Casting

  • Weighing: start the engine, check the clutch is engaged, remove the handle and press UP. Watch the last few metres of chain to avoid damaging the bow.
  • Casting by hand: release the clutch and let the gypsy run; turn the handle counter-clockwise to slow the chain.
  • Casting electrically: press DOWN for a controlled, even release.
  • Once anchored, take the load off the windlass: fasten the chain or secure it to a strong point with a rope.

Troubleshooting

  • Windlass stops but the breaker has not tripped: wait a few seconds and try again – do not keep the button pressed.
  • Breaker tripped: reset it and wait a few minutes before weighing again.
  • Still blocked after several attempts: move the boat to free the anchor.

Maintenance

  • Rinse salt off with fresh water regularly; switch off the motor supply before any manual work.
  • Yearly, drum version: loosen the bush (3) with the handle (1), pull off the drum (4), remove the top clutch cone (5), undo the screws (R1-14, R3-16) to remove the chain stripper (R1-13, R3-17), remove the gypsy (6) and bottom cone (5).
  • No-drum version: remove the gypsy cover (2) with the handle, then as above.
  • Grease the shaft thread and the gypsy cone seats with marine grease; clean and grease the motor and contactor terminals. Gearmotor work only when cold, by qualified personnel.

Spare Parts

Quick Rider R1 exploded view

R1 (exploded drawing page 16)

Code Description Parts (drawing ref.)
FVSSGMSDCP05000 OSP DRUM BUSH DP/E/R1 3 Ask us to source it →
FVSSMSE04000A00 OSP WINDLASS DRUM DP1/R1 4 Ask us to source it →
FVSSCPBBA050A00 OSP GYPSY COVER DP1/R1/E1 2 Ask us to source it →
FVSSCFA05000A00 OSP CLUTCH CONE KIT 500W A/F/R1 5 Ask us to source it →
FVSSB0401400A00 OSP GYPSY 1/4" DP1/E1/R1 6 - 24 Ask us to source it →
FVSSB0406000A00 OSP GYPSY 6mm DP1/E1/R1 6 - 24 Ask us to source it →
FVSSBDP10C00A00 OSP WINDLASS BASE SERIES R1 12-13-14-20-21-22-23-25-26 Ask us to source it →
FVSSAA050000A00 OSP SHAFT KIT A/F/R1 7-8 9-10-11-15-16-17 Ask us to source it →
FVSSAA0500D0A00 OSP SHAFT KIT A/F/R1 D 7-8 9-10-11-17-18-19 Ask us to source it →
FVSSTR005007A00 OSP TOP R1 1/4' 2, from 5 to 17, from 20 to 26 Ask us to source it →
FVSSTDP1D006A00 OSP TOP R1 6mm D / OSP TOP R1 D 6MM (same code printed twice) as printed Ask us to source it →
FVSSTR005D07A00 OSP TOP R1 D 1/4' from 3 to 14, from 17 to 26 Ask us to source it →
FVSSLVSDN0000A00 OSP STRAIGHT WINDLASS LEVER 1 Ask us to source it →

Quick Rider R3 exploded view

R3 (exploded drawing page 17)

Code Description Parts (drawing ref.)
FVSSGMSDCPAL100 OSP DRUM BUSH E3/R3/TB3 3 Ask us to source it →
FVSSMSE10AL0A00 OSP WINDLASS DRUM R3/E3/TB3 4 Ask us to source it →
FVSSCPBBA100A00 OSP GYPSY COVER DP3/R3/E3 2 Ask us to source it →
FVSSCFA10000A00 OSP CLUTCH CONE KIT 1000W A/F/R3 5 Ask us to source it →
FVSSB1006000A00 OSP GYPSY 6MM R3 6 - 23 Ask us to source it →
FVSSB1008516A00 OSP GYPSY 8MM-5/16" R3 6 - 23 Ask us to source it →
FVSSB101038AA00 OSP GYPSY 10MM-3/8" R3 6 - 23 Ask us to source it →
FVSSBR010C00A00 OSP SHAFT KIT A/F/R3 (as printed) 12, from 16 to 22-24 Ask us to source it →
FVSSAA100000A00 OSP SHAFT KIT A/F/R3 8-9-10-11-14-15 Ask us to source it →
FVSSAA1000D0A00 OSP SHAFT KIT A/F/R3 D 8-9-10-11-13-15 Ask us to source it →
FVSSTR010006A00 OSP TOP R3 6MM 2, from 5 to 12, from 14 to 22-23-24 Ask us to source it →
FVSSTR010008A00 OSP TOP R3 8MM-5/16" as above Ask us to source it →
FVSSTR010010A00 OSP TOP R3 10MM-3/8" as above Ask us to source it →
FVSSTR010D06A00 OSP TOP R3 D 6MM from 3 to 13, from 15 to 22-23-24 Ask us to source it →
FVSSTR010D08A00 OSP TOP R3 D 8MM-5/16" as above Ask us to source it →
FVSSTR010D10A00 OSP TOP R3 D 10MM-3/8" as above Ask us to source it →
FVSSLVSP00R2A00 OSP FOLDED WINDLASS LEVER 1 Ask us to source it →

Quick Rider motorgearbox exploded views

Motorgearboxes

Code Description Motorgearbox
FVSSMR05TG40B00 OSP GEARBOX 500W WINDLASS QUICK TG40 R1 500W Ask us to source it →
FVSSMR0540HSB00 OSP GEARBOX 500W WINDLASS QUICK TG40 HS R1 500W Ask us to source it →
FVSSR0512Q00B00 OSP MOTORGEARBOX 500W 12V QUICK R1 500W Ask us to source it →
FVSSR0512QHSB00 OSP MOTORGEARBOX 500W 12V QUICK HS R1 500W Ask us to source it →
FVSSR0524Q00B00 OSP MOTORGEARBOX 500W 24V QUICK R1 500W Ask us to source it →
FVSSR0524QHSB00 OSP MOTORGEARBOX 500W 24V QUICK HS R1 500W Ask us to source it →
FVSSM0512000A00 OSP WINDLASS MOTOR 500W 12V / 500W 24V (same code printed for both) 500W Ask us to source it →
FVSSMR10TG50B00 OSP GEARBOX 1000W QUICK WINDLASS R1 700/1000W Ask us to source it →
FVSSR0712Q00B00 OSP MOTORGEARBOX 700W 12V QUICK R1 700/1000W Ask us to source it →
FVSSR1012Q00B00 OSP MOTORGEARBOX 1000W 12V QUICK R1 700/1000W Ask us to source it →
FVSSR0724Q00B00 OSP MOTORGEARBOX 700W 24V QUICK R1 700/1000W Ask us to source it →
FVSSR1024Q00B00 OSP MOTORGEARBOX 1000W 24V QUICK R1 700/1000W Ask us to source it →
FVSSM0712000A00 OSP WINDLASS MOTOR 700W 12V 700/1000W Ask us to source it →
FVSSM1012000A00 OSP WINDLASS MOTOR 1000W 12V 700/1000W Ask us to source it →
FVSSM0724000A00 OSP WINDLASS MOTOR 700W 24V 700/1000W Ask us to source it →
FVSSM1024000A00 OSP WINDLASS MOTOR 1000W 24V 700/1000W Ask us to source it →
FVSSMR15TG70A00 OSP GEARBOX 1500W QUICK WINDLASS 1400W Ask us to source it →
FVSSR1412Q00A00 OSP MOTORGEARBOX 1400W 12V QUICK 1400W Ask us to source it →
FVSSR1424Q00A00 OSP MOTORGEARBOX 1400W 24V QUICK 1400W Ask us to source it →
FVSSM1412000A00 OSP WINDLASS MOTOR 1400W 12V 1400W Ask us to source it →
FVSSM1424000A00 OSP WINDLASS MOTOR 1400W 24V 1400W Ask us to source it →

Dimensions are on page 22 of the manual.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual