We Ship Worldwide! Shipping information.
OWNER'S MANUAL

Installation, IN/OUT push-button operation, manual mode, maintenance and spare parts for the Selden E40rev to E66rev reversing electric self-tailing winches on the SEL-Bus system.

DocumentSelden Reversing Electric Winches E40rev–E66rev Owner's Manual
FormatPDF · 40 pages · 9.6 MB
LanguageEnglish
Download PDFView Collection
SpecificationsIncluded PartsInstallationOperationTroubleshootingMaintenanceSpare PartsProducts
Selden Reversing Electric Winches E40rev–E66rev — Owner's Manual

Dimensions and Technical Data

Model H mm ØD mm Ød mm Line mm Ratio high / low Weight kg Max line speed m/min SWL kN ECL kN
E40rev 202 152 75 8-12 13:1 / 40:1 9.4 15 11.2 6.7
E46rev 226 184 90 10-14 13:1 / 46:1 12.7 11 12.9 9.7
E52rev 226 184 90 10-14 15:1 / 52:1 12.7 11 14.6 9.7
E60rev 279 245 120 10-16 18:1 / 60:1 22.8 8 16.8 14.7
E66rev 279 245 120 10-16 20:1 / 66:1 22.8 8 18.5 14.7

For best performance use a line diameter in the middle of the allowed range.

Selden Erev reversing electric winch main components exploded view

Winch + Motor Pack

Model Winch, aluminum drum Motor pack Fasteners to motor pack Template
E40rev 475-140-05 473-430-05 4x 162-061 597-510
E46rev 475-146-05 473-530-05 5x 162-061 597-511
E52rev 475-152-05 473-530-05 5x 162-061 597-511
E60rev 475-160-05 473-630-05 5x 162-047 597-512
E66rev 475-166-05 473-630-05 5x 162-047 597-512

Also included: motor cable kit (5m cable) 471-275-10 and winch tool 473-010.

Deck Fasteners (not supplied)

Model Fasteners Through deck M-thread drill
E40rev 5 pcs socket head M6 Ø7.0 Ø5.0
E46rev, E52rev 5 pcs socket head M8 Ø9.0 Ø6.8
E60rev, E66rev 5 pcs socket head M10 Ø11.0 Ø8,5

Marine grade stainless, rated by the installer. Large hole: ø 102-105 mm hole saw.

Mounting the Winch

  1. Mark the centre with the template and cut the large hole; fit the motor pack in it.
  2. Remove top cover (winch tool), self-tailing arm, locator bracket and drum, leaving the roller bearings on the base.
  3. Seat the winch base on the motor pack, located on the gear shaft and small locating pin; orient it for the load and lift it off without moving the motor pack.
  4. Mark and drill the fastening holes, countersink the tops, tap if threading; check the fit.
  5. Feed the cables through; put the included contact grease inside the connector and on the motor-pack pins; fit connector seal and connector with its two screws.
  6. Seal fasteners and the motor-pack contact face with a non-hardening compound (e.g. Butyl) – no glue; fit and tighten.
  7. Bolt the winch base to the motor pack, refit drum, bracket and arm, tighten the top cover. Connect the three cables to the terminals shown on the MCU – the correct MCU for that winch.

Electric

Buttons Action
"IN" Winch in, low speed
Hold "IN" + press "OUT" Winch in, high speed
"OUT" Reverse out, low speed
Hold "OUT" + press "IN" Reverse out, high speed

Line over the arm, through the jaws and into the "hook" on the arm; make sure it sits properly in the self-tailer before reversing.

Manual

  • A locking winch handle is required; the winch will not reverse with a handle fitted.
  • Turn slowly to engage the manual gearing and check the handle has locked – otherwise the spring-loaded plunger ejects it.
  • Anticlockwise = high speed, clockwise = low speed. Remove the handle to return to electric mode; under load, run the winch IN briefly before it can reverse.

Trouble Shooting

Problem Cause Action
Loss of self-tailing Line not seated; too few turns; wrong line size Re-seat the line; add turns; correct line size
Not ratcheting Ratchet gears reassembled wrongly; maintenance due Flip the ratchet gears to match pawl engagement; service
Not reversing Winch handle installed; drive shaft gear engaged (plunger at the bottom of the socket) Remove the handle; run the winch IN briefly; service
No response to push-buttons Power off; faulty electric installation Switch on; check cables, button configuration and SEL-Bus fault codes

Yearly Winch Service

  • Strip as for the S-winch: top cover, arm, locator bracket, drum, roller bearing(s), drum washer, drive shaft (friction lock), gear shafts and gears.
  • Clean in white spirits; pawl oil on the pawls (not grease); grease inside the small ratchet gear and the raised surface inside the large one.
  • Clean the drive shaft and put pawl oil on its sliding surfaces; grease all gears and the drum gear. Do not grease the roller bearing(s).

Yearly Motor Pack Service

  • Remove retaining ring, washer, gear, pawls and springs, then the top plate.
  • Remove the ratchet hub (and washer on the E40rev); no degreaser on parts still attached to the base plate.
  • Grease shaft, gears, output shaft and the top-plate seal; pawl oil on the pawls; replace a deformed locking ring.
  • Extended motor-pack maintenance every five years by a technician: manual 597-981.

Spare Parts

Art. No. Description Size
162-061-10R Fastener kit, winch to motor pack (4x M8x35) E40
162-061-11R Fastener kit (5x M8x35) E46/52rev
162-047-10R Fastener kit (5x M10x40) E60/66rev
583-193-10R Pawl and washer kit (motor pack) E40rev
583-193-11R Pawl and washer kit (motor pack) E46/52rev
583-193-12R Pawl and washer kit (motor pack) E60/66rev
473-314-01R Top cover S30
473-414-01R Top cover S40
473-524-01R Top cover S46
473-514-01R Top cover S52
473-624-01R Top cover S60
473-614-01R Top cover S66
473-495R Self-tailing arm E40rev
473-595R Self-tailing arm E46/52rev
473-695R Self-tailing arm E60/66rev
473-494-10R Self-tailing jaw kit E40rev
473-594-10R Self-tailing jaw kit E46/52rev
473-694-10R Self-tailing jaw kit E60/66rev
473-496R Line stripper E40rev
473-596R Line stripper E46/52rev
473-696R Line stripper E60/66rev
Art. No. Description Size
470-029-11R Gear service kit S30/40 View part →
470-029-12R Gear service kit S46/52 View part →
472-005-11R Gear service kit S60/66 View part →
473-315-01R Gear shaft S30 Ask us to source it →
473-415-01R Gear shaft S40 Ask us to source it →
473-516-01R Gear shaft S46/52 Ask us to source it →
473-615-01R Gear shaft S60/66 Ask us to source it →
473-412R Locator bracket S30/40 Ask us to source it →
473-512R Locator bracket S46/52 Ask us to source it →
473-612R Locator bracket S60/66 Ask us to source it →
473-548-10R Bearing kit S30/40 Ask us to source it →
473-547-10R Bearing kit S46/52 Ask us to source it →
473-549-10R Bearing kit S60/66 Ask us to source it →
473-321-10R 2-speed gear S30 Ask us to source it →
473-421-10R 2-speed gear S40 Ask us to source it →
473-522-10R 2-speed gear S46 Ask us to source it →
473-521-10R 2-speed gear S52 Ask us to source it →
473-622-10R 2-speed gear S60 Ask us to source it →
473-621-10R 2-speed gear S66 Ask us to source it →
320-089-10R Drive gear S30 Ask us to source it →
320-075-10R Drive gear S40 Ask us to source it →
320-076-10R Drive gear S46/52 Ask us to source it →
320-077-10R Drive gear S60/66 Ask us to source it →
473-010R Winch tool S30/40, S46/52, S60/66 View part →
Item No. Optional part
474-501-10 10" Race GRIP winch handle View part →
474-401-10 8" Race GRIP winch handle View part →
474-301-10 10" STANDARD winch handle View part →
474-201-10 8" STANDARD winch handle View part →
312-501 Selden lubrication grease (90g) View part →
312-709-01 Pawl oil (50 ml) View part →

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual