Selden SEL-Bus Emergency Stop & Relay — Installation Manual
INSTALLATION MANUAL
Part numbers, relay sizing, mounting with or without the guard, terminals and wiring for the Selden SEL-Bus emergency stop button and relay.
DocumentSelden SEL-Bus Emergency Stop & Relay Installation Manual
FormatPDF · 16 pages · 1.5 MB
LanguageEnglish
What the Manual Covers
| Part No. | Description | |
|---|---|---|
| 540-648 | Emergency stop button | Ask us to source it → |
| 540-649-01 | Protective guard for emergency stop button | Ask us to source it → |
| 532-498 | Relay 12V 100A | Ask us to source it → |
| 532-499 | Relay 24V 100A | Ask us to source it → |
| 532-599 | Relay 12/24V 250A | Ask us to source it → |
The relay switches the incoming power to the SEL-Bus PSU. Size it for voltage and load: 100A per PSU in a 12V installation, 50A per PSU at 24V.
| Relay | Voltage (V) | Current (A) | Power consumption (W) |
|---|---|---|---|
| 532-498 | 12 | 100 | 6 |
| 532-499 | 24 | 100 | 6 |
| 532-599 | 12/24 | 250 | 3 (45 on start up) |
With Protective Guard (recommended)
- Choose fasteners with a head smaller than Ø 9.5x4mm and thread smaller than Ø5mm (e.g. MLC6S M5, MRT M5).
- Drill the mounting holes.
- Attach the button to the guard.
- Connect the cables.
- Apply sealant in the grooves under the guard.
- Fasten button and guard.
Without Guard
- Max. mounting surface thickness 4mm; if thicker, make a 40mm countersink on the back.
- Drill the mounting hole.
- Fit the button with its nut.
- Connect the cables. On an uneven surface extra sealant may be needed.
Mount the button within easy reach whenever SEL-Bus devices are in use.
Terminals & Wiring
| Unit | Terminal | Connector | Use |
|---|---|---|---|
| Stop button | 11 & 12 | Blade receptacle 2.8x0.5mm | Normally closed contact, to the relay |
| Stop button | X1- & X2+ | Blade receptacle 2.8x0.5mm | Optional LED, 12-24V, best on the navigation light switch |
| Relay 532-498 / 532-499 | 30 & 87 | Ring terminal, M6 | Power terminals |
| Relay 532-498 / 532-499 | 85 & 86 | Blade receptacle 6.8x0.8mm | Control terminals, relay coil |
| Relay 532-599 | +A1 & -A2 | Ring terminal, M8 | Power terminals |
| Relay 532-599 | Red & black cables | – | Control terminals, relay coil |
| Relay | Voltage (V) | Fuse current rating (A) | Min cable area (mm2)* |
|---|---|---|---|
| 532-498 | 12 | 2 | 1 |
| 532-499 | 24 | 1 | 0.35 |
| 532-599 | 12 | 4 | 1 |
| 532-599 | 24 | 2 | 0.35 |
- *Max. cable length 10m.
- Recommended circuit: +12/24V from the fuse and battery disconnect switch, through the relay power terminals to PSU +; the stop button (11/12) in the relay coil circuit via its fuse.
- A remote power switch can be added in the coil circuit (second wiring diagram in the PDF).
- Warranty 2 years when installed, operated and maintained per the manual.
Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.
Products in this Manual
