We Ship Worldwide! Shipping information.
OWNER'S MANUAL

Specifications, deflector setting, attaching to cable or rod, measurement practice, gauge check, app connection and troubleshooting for the Spinlock Rig-Sense Pro electronic rig tension gauge (firmware 2.8).

DocumentSpinlock Rig-Sense Pro Instructions
FormatPDF · 22 pages · 19.2 MB
LanguageEnglish
Download PDF
SpecificationsMeasuringGauge CheckPower & CareProducts
Spinlock Rig-Sense Pro — Instructions

Product Specification

Item Value
Product code RGS-PRO/0520
Cable range Cable Ø5 to 20 mm; rod -6 (Ø5.0mm) to -60 (Ø16.8mm)
Accuracy +/-1% of cable breaking strength (equivalent to +/-4% of 25% BS)
Max. tension 8000 kg
Device size / weight 500 × 50 × 161 mm; 3.2 Kg
Package size / weight 625 × 360 × 110 mm; 5.8 Kg
Display 2.0" touch enabled LCD
Battery 3.7V LiPo 2000 mAh, up to 15hrs; USB-C, full in 4hrs
Package contents Rig-Sense Pro, gauge check tool, stopper, calipers, USB to USB-C charging cable, 3 mm Allen key
Warranty Limited warranty up to two years from the original date of purchase

Quick Start

  1. Power on (hold 2s); open the CABLE menu and set the cable type from the Library (or Favourites) and the diameter – always check the diameter with the supplied callipers first.
  2. Confirm the cable; the screen shows the deflector position A–I. Press the chevrons and slide the deflector to that letter, then confirm.
  3. Fit the stopper below the measuring position if the cable has too little friction to support the device.
  4. Push the clamp handle lock down, open the handle fully, route the cable round the bottom sheave then the top sheave, and close the handle slowly until the lock clicks.
  5. Read tension or %BS on the TENSION page; clip the tether to the boat or to yourself.

Never clamp onto a cable unless the deflector is set to the position the device shows: incorrect use damages both cable and device.

Measurement Practice

  • At least 1.5m from any terminations, fittings, knots, splices or hardware.
  • Take readings in two orientations (e.g. rotated 180°) and average them.
  • Repeat readings at the same position; large variations mean reposition and repeat.
  • Measure under steady load only, on a clean section free of twists or damage.
  • Warning Limit in SETTINGS: above the set %BS the TENSION page turns red and a buzzer sounds.

Gauge Check and Calibration

  • Each Rig-Sense Pro is calibrated against the Rig-Sense Pro reference device; the pre-loaded cable settings were calibrated with that device.
  • Use the supplied Gauge Check Tool regularly: check it is straight by rolling it on a flat surface, select Gauge Check (CABLE or SETTINGS menu), set the deflector to "I" and follow the prompts. Green = within range, red = not.
  • "Set Zero" removes small offsets; "Service Required" means the device is outside the acceptable range – contact Spinlock with the serial number and firmware version (Settings > About).
  • A "!" next to the settings icon means a gauge check should be performed. Record results in the Gauge Check Log (in the manual).
  • Device Overload Warning: remove the device immediately, inspect device and cable, and verify calibration with the check tool before reuse.
  • New cable calibrations can be arranged with Spinlock (a 4.1m length of cable with standard rigging eyes is required; a charge applies).

Charging & Travel

  • Charge via USB-C: red light while charging, green when full (approx. 4 hours, up to 15 hours use). Close the charge port flap afterwards.
  • For air travel or shipping the screen and electronics module (with the lithium battery) can be removed with the Allen key (three retaining bolts), powered off.
  • Water-resistant but must not be left submerged. Do not open, modify or repair: no user-serviceable parts inside.
  • Store dry and clean in the case provided; power off correctly after use.

Apps & Troubleshooting

  • Load-Sense app (iOS & Android): live load, peak load, graph, alarms, multiple devices, CSV export.
  • Rig-Sense app: log and share rig tuning guides.
  • Will not power on: charge at least 30 minutes, then press and hold the power button.
  • Not measuring correctly: check attachment and that moving parts are free, restart and repeat.
  • Check for firmware updates (Settings > About > Device Management) before contacting support.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.

Products in this Manual