Ronstan composite V cleats, Open and Fairlead, for 3 to 12 mm control lines on dinghies and catamarans, plus a stainless steel jam cleat for 6 mm line. Click here to read more.

View as

V Cleats for Dinghy and Catamaran Control Lines: Open, Fairlead, and Line Size

A V cleat holds a line in a fixed, low-profile jaw without moving parts. Ronstan describes its V cleats as a simple solution to cleating lines under moderate loads, with control lines on dinghies and catamarans as the stated application. This collection covers the Ronstan composite V cleats in three sizes, in Open and Fairlead versions, plus a small stainless steel jam cleat for 6 mm line.

V Cleat Families in This Collection
  • Ronstan V Cleat Open, composite: three sizes. The Small (RF5100) takes 3 to 6 mm (1/8 to 1/4 in) line on 36 mm hole centres with 4 mm fasteners. The Medium (RF5105) takes 5 to 8 mm (13/64 to 5/16 in) on 55 mm centres with 5 mm fasteners. The Large (RF5110) takes 8 to 12 mm (5/16 to 1/2 in) on 72 mm centres with 6 mm fasteners.
  • Ronstan V Cleat Fairlead, composite: the Small (RF5101) takes 3 to 6 mm on 48 mm centres with 4 mm fasteners, and the Medium (RF5106) takes 5 to 8 mm on 66 mm centres with 5 mm fasteners. The RF5101 listing adds a cutaway in the base that can double as a becket, for a 2:1 purchase.
  • Ronstan V Cleat Jam, stainless steel: the RF494 is described as a stainless steel jam cleat for small diameter, low load lines, such as dinghy halyards and outhauls and flag halyards. It takes 6 mm (1/4 in) line and mounts with two 4 mm fasteners on 56 mm centres.

The composite cleats are PTFE impregnated glass and carbon fibre. Ronstan lists a low, snag-free profile and a base that suits flat and curved surfaces, and the RF5100 listing says abrasion resistance is greater than traditional plastic cleats.

How to Choose a V Cleat
  • Line size first: pick the size whose range contains your line. The ranges overlap (a 6 mm line sits in both the Small and Medium range, an 8 mm line in both the Medium and Large), so also consider how the line is used and how much it loads the cleat.
  • Load: these cleats are listed for moderate-load control lines on dinghies and catamarans. For a line that is set and held under sustained load, such as a halyard, read how to choose between cleats and clutches.
  • Replacing an existing cleat: match the hole centres and fastener diameter above to the holes already in the deck or spar.
  • Open or Fairlead: the listings do not describe the difference beyond the RF5101 becket cutaway, so check the product page for the version you want.
Who It's For

Dinghy and catamaran sailors fitting or replacing control-line cleats, and owners who want a lightweight composite cleat for small-diameter lines. For a line trimmed by hand with a cam jaw, see the cam cleats, or browse the full Ronstan cleats range.

Frequently Asked Questions

What line size does a Ronstan V cleat take?
The Small size takes 3 to 6 mm, the Medium 5 to 8 mm and the Large 8 to 12 mm line. The Large is listed in the Open version only in this collection.

What loads is a V cleat meant for?
Ronstan describes its V cleats as a simple solution for cleating lines under moderate loads, with control lines on dinghies and catamarans as the application. For halyards and other lines held under sustained load, a clutch or jammer is the better fit; see the cleats vs clutches guide.

Can a V cleat make a 2:1 purchase?
The Ronstan V Cleat Fairlead (Small), RF5101, has a cutaway in the base that can double as a becket, and its listing mentions setting up a 2:1 purchase with it.

What are the mounting hole sizes?
Fastener diameter and hole centres are 4 mm and 36 mm (RF5100), 4 mm and 48 mm (RF5101), 5 mm and 55 mm (RF5105), 5 mm and 66 mm (RF5106) and 6 mm and 72 mm (RF5110). The listings do not say that fasteners are included, so confirm on the product page.

Is the stainless steel RF494 a V cleat?
It is titled a V cleat jam, and the listing describes it as a stainless steel jam cleat for 6 mm (1/4 in) low-load lines such as dinghy halyards, outhauls and flag halyards. It has two fastener holes on 56 mm centres.