The Lewmar 60mm HTX Single Block is a 60mm-sheave block with aluminium side cheeks, a central plain bearing and side-thrust Delrin ball bearings, rated for a 1,100 kg (2,422 lb) working load limit and for line up to 12mm (1/2 in). Lewmar designed the HTX range for frequently adjusted, highly loaded systems that use modern line technology and reduced line diameters.
Lewmar HTX blocks at a glance
| Spec | Lewmar 60mm HTX Single |
|---|---|
| Sheave diameter | 60mm (2 1/3 in) |
| Max line size | 12mm (1/2 in) |
| Bearings | Central plain bearing for efficiency at high loads; Delrin ball bearings take the side thrust |
| Body construction | Strong aluminium side cheeks; head design inspired by the Lewmar racing range, with a grub screw swivel head locking mechanism |
| Working load limit | 1,100 kg (2,422 lb) |
| Weight | 215 g (7.5 oz) |
| Configurations in the 60mm HTX range | Single, single with becket, single with becket and cam, double, triple, fiddle, toggle head, upstand |
What is a sailboat block and how does it work?
A sailboat block is a marine tackle block — a pulley system with a rotating sheave housed inside a structural frame — used to redirect and mechanically advantage control lines including sheets, halyards, vangs, and backstays. A single block like the Lewmar 60mm HTX Single Block redirects a line through one sheave, while double, triple, or cascade systems multiply mechanical advantage for heavier loads.
The sheave diameter matters: a larger sheave reduces the bend stress on the rope fibers, which extends line life and cuts friction. Lewmar builds the HTX series around a central plain bearing that carries the load at high loads, supplemented by Delrin ball bearings that absorb side thrust. Lewmar also states that HTX efficiency improves above 450 kg, because the acetal sheaves become self-lubricating at that point.
How do I choose the right HTX block size for my sailboat?
Match the block to the largest line it will carry, and to the working load of the system. Lewmar rates each HTX sheave size for a maximum line size and a working load limit:
| HTX single block | Max line size | Working load limit |
|---|---|---|
| 50mm | 10mm (3/8 in) | 800 kg (1,762 lb) |
| 60mm | 12mm (1/2 in) | 1,100 kg (2,422 lb) |
| 72mm | 14mm (9/16 in) | 2,000 kg (4,405 lb) |
| 90mm | 16mm (5/8 in) | 3,500 kg (7,709 lb) |
Source: Lewmar HTX Blocks catalogue. A line thicker than the block's maximum line size does not belong on that block; step up to the next HTX size. The 60mm single covers lines up to 12mm (1/2 in).
The 60mm HTX range also comes in other configurations. The becket version adds a fixed attachment point to anchor the standing end of a purchase system. The fiddle block puts two sheaves in one body for compact multi-part tackle, and the toggle head block is built to fit onto studs. The upstand version raises the sheave on a base; it is covered in the October 2026 update below. Choosing the correct head style is as important as choosing the right sheave size.
What makes the Lewmar HTX series different from standard blocks?
Lewmar built the HTX range on the design of its racing range, using high-quality materials for reliability. The 60mm single has strong aluminium side cheeks, a central plain bearing for efficiency at high loads and Delrin ball bearings for side thrust. Its head design is inspired by the Lewmar racing blocks and includes a grub screw swivel head locking mechanism.
Lewmar states that HTX blocks are more efficient than an alternative brand using similar material, thanks to a machined bearing pin surface. That means faster sail handling and less rope wear.
How do I inspect and maintain sailboat blocks?
Even high-quality blocks wear faster without basic maintenance. After offshore passages or extended salt-spray exposure, flush all blocks with fresh water to clear salt crystals, then rotate the sheave by hand — any grinding, clicking, or rough spots indicate contamination or wear.
- Inspect the sheave groove for wear or flat spots that indicate overloading.
- Check the side plates for cracks, especially around the attachment point.
- Verify the becket or swivel head (if present) turns freely without binding.
- Replace any block whose sheave shows noticeable side play or rough rotation.
- Re-confirm line-diameter compatibility when replacing running rigging; keep the line within the block's maximum line size.
Update (October 2026): the 60mm HTX Single Block Upstand
The Lewmar 60Mm Htx Single Block Upstand keeps the 60mm HTX sheave and mounts it on an upstand base. Its upstand design suits leading control lines from the mast base or around deck obstructions, and helps keep the deck layout tidy.
| Spec | Lewmar 60mm HTX Single Block Upstand |
|---|---|
| Sheave | 60mm high-load composite sheave |
| Max line size | 12mm (1/2 in), as for the 60mm HTX range |
| Frame | Stainless steel frame with aluminium side plates |
| Bearings | 9+1 |
| Working load limit | 1,100 kg (2,422 lb), per the Lewmar HTX Blocks catalogue |
| Base | 58mm (2 5/16 in) overall diameter, fixed with 4 x M6 (1/4 in) fixings on a 40mm (1 37/64 in) diameter |
Lewmar also lists a rubber boot upstand kit for the 60mm HTX (part 29196065), available as the Lewmar 60Mm Htx Upstand Cv Kit. Size the system to the 1,100 kg (2,422 lb) working load limit and check the fixing size (M6 on the 60mm base) before you drill.
Frequently asked questions
What are pulley blocks used for on a sailboat?
Pulley blocks redirect and multiply line tension across running rigging including mainsheets, halyards, vangs, and cunninghams. Lewmar designed the HTX range for frequently adjusted, highly loaded systems; the 60mm single takes line up to 12mm (1/2 in).
What is the difference between blocks and pulleys on a sailboat?
They serve the same mechanical purpose — redirecting line and reducing hauling load — but a marine block like the HTX carries a working load limit and a maximum line size, so you can size it to the system.
What line size does the 60mm HTX single accept?
Up to 12mm (1/2 in), according to Lewmar. For lighter lines, the 50mm HTX is rated for line up to 10mm (3/8 in).
What is the working load of the 60mm HTX single?
1,100 kg (2,422 lb) working load limit. Every 60mm HTX block in the Lewmar catalogue, including the upstand, carries the same 1,100 kg rating.
Can a Lewmar 60mm HTX single replace a Harken pulley?
It can in many configurations, provided the working load rating, rope-diameter compatibility, and attachment-point dimensions match your existing setup. Always verify the working load against your line-tension requirements before substituting brands.
What is the upstand version for?
The upstand configuration mounts the 60mm HTX sheave on a base that lifts it above the deck, to lead control lines from the mast base or around deck obstructions. See the October 2026 update above for its specs.
Shop all Lewmar Blocks - HTX →
You may also be interested in
- 101 Selden Blocks: Which block type should I use for my boat?
- How to Choose Ratchet Blocks: Types, Sizes and Holding Power
Last updated: October 22, 2026.
