Sleipner S-Link Gateway GW-2Y (PDF)

OWNER'S MANUAL

Link a Yanmar J1939 bus and an NMEA 0183 GPS antenna to your Sleipner S-Link bus with the GW-2Y gateway: supported devices by firmware, pinouts, LED codes, specifications and installation.

DocumentSleipner S-Link Gateway GW-2Y Installation & User Manual

FormatPDF · 11 pages · 1.0 MB

LanguageEnglish

Download PDF

Specifications Yanmar J1939 NMEA 0183 & LEDs Installation S-Link Bus Products

Sleipner S-Link Gateway GW-2Y — Installation & User Manual

GW-2Y at a Glance

Technical Specifications

Parameter	Value
Supply voltage	8-31VDC, powered from S-Link
Power consumption	1 W
CAN INTERFACE (M12 male)	CAN 2.0B, baud rate 250Kb
NMEA 0183 connector	GPS RX @ 4800 baud or 38400 baud
NMEA 0183 power output	Max 100mA (internally fused)
Weight	200g/7.05oz

Measurements

Code	Description	mm	inch
+H	Total gateway height	41	1.6
H	Gateway height	25.5	1
W	Gateway width	50	2
+L	Total gateway length	126.5	5
L	Gateway length	100	3.9

CAN Interface (Yanmar J1939)

GW-2Y connects a Yanmar J1939 bus to S-Link: S-Link spur cable to the backbone, Yanmar bus to the M12 male CAN INTERFACE connector.
GW-2Y does not power the CAN bus and has no termination resistor on the M12 output; CAN-L and CAN-H are galvanically isolated. Sleipner does not supply cables for the CAN bus.
M12 pinout: pin 1 NC, pin 2 NC, pin 3 GND, pin 4 CAN-H, pin 5 CAN-L.
TX / RX LEDs flash (max 100ms on / 100ms off) when sending / receiving.

GW-2Y firmware	Sleipner devices	Yanmar
Version 1.002	PPC520, PPC820, PPC840, AMS 8977	JC20A
Version 1.003	PPC520, PPC820, PPC840, AMS 8977, AMS-2	JC20A

NMEA 0183 GPS Input

V OUT can power a single GPS antenna, max 100mA, internally fused (S-Link bus voltage). RX A(+) and TX B(-) are galvanically isolated.
4800 and 38400 baud are supported and set automatically; $GxRMC sentences from all positioning systems are supported.
NMEA 0183 LED flashes 100ms/100ms for a valid message at 38400 baud, 100ms/900ms at 4800 baud; off = no valid signal.
GNSS priority: 1) NMEA0183 at 100ms update rate, 2) NMEA0183 at 1000ms update rate.
Status LED: off = no power; on = S-Link communication and power OK; flashing 500ms/500ms = power OK but no S-Link communication.

Installing the GW-2Y

Fasten the GW-2Y box to a solid surface with four mounting screws.
Attach the required cables. No external power is needed – GW-2Y is powered from S-Link.

The typical connection diagram in the PDF shows GW-2Y between the Sleipner system (PPC unit, Sleipner panel, thruster switch) and the Yanmar system bus (helm, joystick, display, engine and drive ECUs).

S-Link System Rules

Cables & Connectors

Component	Role
BACKBONE Cable (blue ends)	Common power and communication bus through the vessel; standard lengths
SPUR Cable (green ends)	One per connected product, no exceptions; keep as short as practical
POWER Cable	Required in every installation; only one per BACKBONE; protect with a 2A fuse. Yellow and black wires to GND, red to +12VDC or +24VDC
T-Connector	One per SPUR or POWER Cable on the BACKBONE
4-Port T-Connector	Several SPUR Cables on one point; two sealing caps for unused ports
BACKBONE Extender	Joins two BACKBONE Cables
END Terminator	One at each end of the BACKBONE bus

Installation Rules

Keep BACKBONE and SPUR lengths to a minimum; consult your distributor if the total BACKBONE exceeds 100 meters.
Fasten cables to avoid sharp bends, chafe and strain on connectors; close the connector locks fully.
Do not leave cables, T-Connectors or Extenders permanently immersed; make a U-bend before each product connector so water does not run into it.
Ideally connect the POWER Cable in the middle of the BACKBONE for equal voltage drop at both ends.
Route S-Link away from radio transmitters, antennas and high voltage cables.
Unused SPUR cables may be left unterminated for future equipment: protect the open connectors from water.
Connect only original Sleipner S-Link products or authorised equipment directly to the bus; third-party equipment goes through a Sleipner interface, and at least one original Sleipner control panel must still be installed.

Need a part that isn't listed? Ask us to source it and quote the part number from the PDF.